Global Fire Equipment ADLI V2 FO Owner's manual

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
ADLI V2 FO
Addressable Loop Interface
INSTALLATION / PROGRAMMING MANUAL
GENERAL DESCRIPTION
The ADLI FO V2 is an addressable loop fibre optic interface which allows a conventional ORION / ORION-EX V2
panel to be integrated in any of GFE’s analogue addressable systems, allowing the addressable panel to monitor
and control the status of the conventional panel. An 8 way DIL switch is provided to set the module’s address and to
configure the advanced features.
There are two assemblies of the ADLI V2 FO: ADLI V2 FO LOOP and ADLI V2 FO ORION. Every ORION / ORION-EX V2
panel has to be equipped with one ADLI V2 FO ORION and every link that connects to the loop has to be equipped with one
ADLI V2 FO LOOP.
MAIN FEATURES
● Fast activation response
● Three status LEDs
● Remote sound / Silence alarms
● Remote reset
● Low power consumption
● Automatic conventional panel recognition
● Fault and fire status report
● Different analogue values for zone, panel and supply faults for easier troubleshooting
● Programmable number of addresses to report (for ORION conventional panel)
● Programmable extinguishing, pre-release delay, sounder and disablements status report
using 4 additional addresses reporting as I/Os (ORION-EX V2 panel only)
IMPORTANT SAFETY NOTES
● This equipment must only be installed and maintained by a suitably qualified and technically competent person.
● A basic knowledge and training in the installation of Fire and Extinguish Detection systems is assumed.
● The fire detection system should be designed by a suitably qualified person with reference to the local Regulations
and Guidance from the Fire Officer where applicable.
1
www.acornfiresecurity.com
www.acornfiresecurity.com

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
COMPATIBILITY NOTE
ADLI V2 FO module is only compatible with ORION / ORION-EX V2 panels that exhibit the following sequential LED pattern
during RESET:
ORION LED pattern
ORION-EX V2 LED pattern
REPORTING DETAILS
ADLI V2 FO LOOP
ADLI V2 FO ORION
STATUS LEDS
GREEN LED - This LED will flash every time the addresses associated with the module are polled
by the addressable panel.
YELLOW LED - This LED will be lit whenever there is a fault condition associated to the
conventional panel.
RED LED - This LED will be lit whenever there is a FIRE condition present on the conventional panel.
Please note that, if the conventional panel is in TEST mode, no fire condition will be reported to the
addressable panel.
2
www.acornfiresecurity.com
www.acornfiresecurity.com

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
REPORTED ANALOGUE VALUES
The ADLI V2 FO reports different analogue values depending on the status and type of fault present on the conventional
panel, allowing a faster troubleshooting.
The table below describes the different analogue values reported to the addressable panel.
REPORTED ANALOGUE VALUE
NORMAL OPERATION
16
ZONE FAULT
4
PANEL FAULT
8
CONVENTIONAL PANEL POWER SUPPLY FAULT
2
FIRE CONDITION / ACTIVATED CONDITION
64
CONNECTING THE ADLI V2 FO
CONNECTING ONE ORION / ORION EX V2 PANEL
3
www.acornfiresecurity.com
www.acornfiresecurity.com

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
CONNECTING MORE THAN ONE ORION / ORION EX V2 PANEL
ADDRESS D.I.L. SWITCH CONFIGURATION
Switches 1-7: Used to address the module.
Switch 8: Not used (Special function on programming mode).
ADDRESS SETTINGS
The ADLI V2 FO can assume from one to eight consecutive addresses depending on the programmed settings (refer to
ADVANCED PROGRAMMABLE FEATURES section of this manual) and the type of conventional panel that it is connected
to, ORION or ORION-EX V2.
If connected to an ORION conventional panel, the ADLI V2 FO assumes only one address, by default, but can be configured
to assume one address per zone. If it is configured to have one address per zone, the ADLI V2 FO will assume 2 / 4 / 8
consecutive addresses, starting from the address that is set on the D.I.L. switch. Every address set reports to the analogue
addressable panel as a ZONE MONITOR UNIT.
If connected to an ORION-EX V2, the ADLI V2 FO assumes, by default, four consecutive addresses, one per each fire
detection zone. If the I/O REPORT advanced programmable feature is set to ACTIVE, then the module will assume four
additional consecutive addresses reporting as I/O to the analogue addressable panel (four additional details refer to
ADVANCED PROGRAMMABLE FEATURES section of this manual).
4
www.acornfiresecurity.com
www.acornfiresecurity.com

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
5
www.acornfiresecurity.com
www.acornfiresecurity.com

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
ADVANCED PROGRAMMABLE FEATURES
PROGRAMMING MODE D.I.L. SWITCH CONFIGURATION
In order to set the module in programming mode first POWER OFF your module then set DIL switches 1 to 7 to OFF and
switch 8 to the ON position, as indicated on the image below. Finally POWER ON your module.
Switches 1-7: Used to select programming parameter and assigned value
Switch 8: Programming Mode
When in programming mode the 2 LEDs (Green and Red) will flash alternatively. The unit will remain in programming mode
while SW 8 is in the ON position. When switch 8 goes from ON to the OFF position the settings indicated on switches 1
through 7 will be recorded on the non-volatile memory of the module. If a new parameter has been accepted, the Green LED
will flash 4 times. When programming is not accepted the Red indicator will remain on for an extra 3 seconds.
PROGRAMMABLE OPTIONS
NUMBER OF ADDRESSES TO REPORT
NOTE:  This configuration will only have effect when the ADLI V2 FO is to be used with an ORION
Conventional Fire Detection Panel.
This programmable feature allows the user to configure the ADLI V2 FO to report to the addressable panel with only one
address or with one address per zone. The address/addresses configured will report as ZONE MONITOR UNITS (ZMU).
When the ADLI V2 FO is configured to report with ONE ADDRESS ONLY, it will only assume one address on the loop and
any fault or fire condition present on the conventional panel will be reported on that same address.
If the ADLI V2 FO is configured to report with 2 / 4 / 8 ADDRESSES, it will assume 2 / 4 / 8 consecutive addresses on the
loop (e. g. if the configuration is 4 addresses and the D.I.L. switch addressing is set to address number one, the ADLI V2 FO
will report on addresses number 1, 2, 3 and 4  ), one per each zone of the ORION conventional panel. Any fault or fire
condition present on one of the conventional panel zones will be reported to the addressable panel on it’s associated
address. Any other conventional panel fault will be reported on the first address set on the D.I.L. switch.
REMOTE RESET / SILENCE SOUNDERS
This programmable feature allows the ORION / ORION-EX V2 panel to be controlled remotely from any of GFE’s analogue
addressable panels, allowing the user to SILENCE / RESOUND Alarms (EVACUATION) and reset the panel from the
addressable panel.
If this function is set to not active, the sounders can still be activated from the addressable panel but it will not be possible to
silence the sounder nor perform a remote reset.
This function is ACTIVE by default to ORION panel and NOT ACTIVE by default to ORION-EX V2 panel.
6
www.acornfiresecurity.com
www.acornfiresecurity.com

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
I/O REPORT
NOTE:  This configuration will only have effect when the ADLI V2 FO is to be used with an ORION-EX V2
Conventional Extinguishing Panel.
This programmable feature allows the user to configure the ADLI V2 FO to report the state of ORION-EX V2’s
S1 sounder, Pre-release delay, REM and general disablement LED, using four additional consecutive
addresses reporting as Input/Outputs (I/O) to the addressable address.
An Output activation command from the addressable panel to the first I/O (S1 sounder) will activate the
evacuation on the ORION-EX V2 conventional panel.
This allows, if more than one conventional panel is connected to an addressable panel though an ADLI V2 FO
module, to activate an evacuation individually on each conventional panel via, e.g., a call point activating a I/O
group containing the S1 sounder I/O address.
PROGRAMMING THE ADLI V2 FO
In order to program the different functions available use switches 1 through 7 as shown below:
A – The first 3 switches select the function to be programmed.
B – Switches 4 through 7 select the value for the function to be programmed.
The table below shows the available functions and correspondent values, as well as the D.I.L. Switch configuration needed
to obtain the desired Output configuration:
FUNCTION
VALUE
DIL SWITCH
SW1
SW2
SW3
DIL SWITCH
SW4
SW5
SW6
SW7
NUMBER OF
ADDRESSES TO
REPORT
(ORION PANEL
ONLY)
ON
OFF
OFF
ONE ADDRESS (Default)
OFF
OFF
OFF
OFF
TWO ADDRESSES (to be used
with ORION 2 ZONES)
ON
OFF
OFF
OFF
FOUR ADDRESSES (to be
used with ORION 4 ZONES)
OFF
ON
OFF
OFF
EIGHT ADDRESSES (to be
used with ORION 8 ZONES)
ON
ON
OFF
OFF
REMOTE RESET /
SILENCE SOUNDERS
OFF
ON
OFF
NOT ACTIVE
(Default for ORION-EX V2)
OFF
OFF
OFF
OFF
ACTIVE
(Default for ORION)
ON
OFF
OFF
OFF
I/O REPORT
(ORION-EX V2
PANEL ONLY)
ON
ON
OFF
DO NOT REPORT I/Os
(Default)
OFF
OFF
OFF
OFF
REPORT I/Os
ON
OFF
OFF
OFF
7
www.acornfiresecurity.com
www.acornfiresecurity.com

Global Fire Equipment // globalfire.pt
ma_adlifo_01_020000_en_200714
STEP BY STEP ADVANCED FEATURES CONFIGURATION EXAMPLE
NUMBER OF ADDRESSES TO REPORT FUNCTION
Let's assume that the ADLI V2 FO is to be used with an ORION Conventional Fire Detection Panel with 8 fire detection
zones, and the desired configuration is to report one address per zone.
STEP 1: Remove power from the ORION panel and assure that the module is connected to the panel with
the 5 way flat cable.
STEP 2: Set D.I.L. Switches 1 to 7 to OFF position and D.I.L. Switch 8 to ON position.
STEP 3: Power up the Panel. The two LEDs flashing alternatively on the module indicates that the module is in
programming mode.
STEP 4: Set the D.I.L. Switches 1 to 3 to NUMBER OF ADDRESSES REPORT (SW1: ON, SW2: OFF & SW3: OFF).
STEP 5: Set the D.I.L. switches 4 to 7 to EIGHT ADDRESSES (SW4: ON, SW5: ON, SW6: OFF & SW7: OFF).
STEP 6: Set the Switch 8 to OFF position. The Green LED will flash 4 times. The module is now programmed to report to
the analogue addressable panel with 8 addresses.
STEP 7: Configure the desired address on the ADLI V2 FO and reset the ORION panel.
TECHNICAL SPECIFICATIONS
PRIMARY SUPPLY VOLTAGE - IN
28.5 V DC nominal - 17 to 30 V DC
SUPPLY CURRENT
ADLI V2 FO ORION - 8.6 mA
ADLI V2 FO LOOP - Ext. Supply: 6.4 mA / Loop: 0.5 mA
MAX. HUMIDITY / OPERATING TEMPERATURE
95 % RH Non-Condensing / 0ºC to 40ºC
DIMENSIONS
ADLI V2 FO ORION - 135 (L) x 36 (W) x 13 (H) mm
ADLI V2 FO LOOP - 135 (L) x 36 (W) x 11 (H) mm
WEIGHT
20 g
8
www.acornfiresecurity.com
www.acornfiresecurity.com