Globe Scientific GCC-MP User manual

What’s in the box:
• Centrifuge
• Power Cable(s)
• Rotor Wrench
• Spare Fuses (2 each)
• Door Key (small screwdriver)
• Quick Start Guide
GCC-MP / Multi-Purpose
Clinical Centrifuge
Quick Start Guide
UNPACKING THE UNIT
Please be sure to remove any packing materials used during initial shipment:
1) Open the lid: Use the included Door Key to press the buttons
on the right and left sides of the unit.
2) Remove foam pads at the hinge latches.
Continued . . .
INSTALLING AND BALANCING THE ROTOR
IMPORTANT: The rotor should always be loaded in a balanced
manner to avoid personal injury and to ensure centrifuge
longevity.
• When any tube is loaded, a tube of the same type, volume and
weight must be added in the opposite rotor location.
• Never intentionally run the centrifuge in an unbalanced
condition even if operation is not affected.
Locking Nut
Load the Rotor Onto the Shaft Symmetrically Load Centrifuge Tubes Into Rotor
Rotor Lid Knob
Install the Rotor Lid

CONTROL PANEL
GCC-MP / Multi-Purpose
Clinical Centrifuge
Quick Start Guide
Continued . . .
Deceleration � � � � � Press to adjust the deceleration rate.
0: No braking applied.
9: Most braking applied.
Memory � � � � � � � � � � Momentarily press to cycle through the
memory locatons. Once the parameters
are adjusted to the desired values, press
and hold for 5 seconds to save the values
in that memory location.
Adjustment Knob Rotate clockwise to increase parameter
values. Rotate counterclockwise to
decrease parameter values. Press to
switch between speed and RCF.
Pulse � � � � � � � � � � � � � Press to accelerate and hold at the set
speed. The centrifuge stops immediately
once this button is released.Radius
Door� � � � � � � � � � � � � � Press to open the lid. This button is not
enabled while the centrifuge is running.
Start / Stop � � � � � � � Press to start the centrifuge. Press to
stop if centrifuge is already running.
Acceleration� � � � � � Press to adjust the acceleration rate.
1: Slowest acceleration rate.
9: Fastest acceleration rate.
1
2
3
4
5
6
7
OPERATION
IMPORTANT: Plug unit into appropriate main supply based on the rated voltage.
1 2 3 4 5 6 7
Speed Display Temperature
Display
Time Display Acceleration
Display
Deceleration
Display
Memory Location
Display

®
Customer Service, Sales and Technical Support:
Phone: [phone] • 1 [phone]
Fax: 1(201)599-1406•E-mail:mail@globescientic.com
©2020GlobeScienticInc.Allrightsreserved.TheGlobeScienticlogoisaregisteredtrademarkofGlobeScienticInc.GCC-MPGuide20050
For the full User Manual, please visit www.globescientic.com
The centrifuge rotor can separate samples whose density is lower than 2.0g/ml. If the separated sample’s density is over 2.0g/ml, please
calculate the allowable speed using the following formula:
Allowable Speed (rpm) = Maximum Speed × (2�0(g/ml) / Sample Density (g/ml))1/2
GCC-MP / Multi-Purpose
Clinical Centrifuge
Quick Start Guide
Rotor Tube Adapter Maximum Maximum Centrifugal Maximum
Type Type Required Speed (rpm) Radius (cm) RCF (×g)
2.0/1.5mL x 30 — 6000 10 4020
  0.2mLx30 GCM-24-AD2 6000 8.5 3415
  0.5mLx30 GCM-24-AD5 6000 9 3618
2.0/1.5mL x 60 — 6000 10 4020
  0.2mLx60 GCM-24-AD2 6000 8.5 3415
  0.5mLx60 GCM-24-AD5 6000 9 3618
8-PCR x 12 — 6000 10 4020
0.2mL x 96 — 6000 10 4020
50mL x 6 — 6000 10.7 4306
15mL x 30 — 4500 R1 = 14.2 3210
R2 = 12.2 2760
15mL x 16 — 5000 12.4 3460
50mL x 8 — 5000 12.4 3460
  100mLx4 GCC-MP-SWING-100ML4 4000 15.9 2840
  50mLx4 GCC-MP-SWING-50ML8 4000 15.9 2840
10mL x 16
  12mLx16 GCC-MP-SWING-15ML16 4000 15.1 2700
15mL x 16
3mL x 36
7mL x 36 GCC-MP-SWING-7ML36 4000 14.7 2630
MTP — 4000 12.1 2160
(128 x 85.6 x 15)
Cell Culture — 4000 12.1 2160
(128 x 85.6 x 21)
DWP — 4000 12.1 2160
(128 x 85.6 x 45)
Kits — 4000 12.1 2160
(128 x 85.6 x 60)
GCC-MP-2ML60
GCC-MP-2ML30
GCC-MP-PCR
GCC-MP-50ML6
GCC-MP-15ML
GCC-MP-50ML8
GCC-MP-SWING
GCC-MP-SWING-
PLATE