Go Rhino 3160MB User manual

1
PACKING LIST
QTY PARTS DESCRIPTION
2 ¼” X ¾” BUTTON HEAD BOLTS
6 5/16” X 3/4” BUTTON HEAD BOLTS
6 5/16” LOCK NUTS
6 3/8” X 1” BUTTON HEAD BOLTS
4 3/8” X 1 1/4” HEX BOLTS
6 3/8” LOCK WASHERS
2 3/8” HEX NUTS
4 3/8” FLAT WASHERS
QTY PARTS DESCRIPTION
2 3160 SIDE PLATES
1 3162P PASSENGER BRUSH GUARD
1 3162D DRIVER BRUSH GUARD
1 C9P PASSENGER HEAD LIGHT PROTECTOR
1 C9D DRIVER HEAD LIGHT PROTECTOR
1 ST3006 3” X 35 ¾” BOTTOM STEP TUBE
1
1TT3534 2” X 35 ¾” TOP TUBE CP3036 35 ¾” SPECIAL CENTER PLATE
ASSEMBLY
STEP 1. BEGIN THE GRILLE AND BRUSH GUARD ASSEMBLY BY LAYING THE COMPONENTS OUT ON A PROTECTIVE
SURFACE.
STEP 2. POSITION THE GRILLE GUARD SIDE PLATES WITH THE FRONT EDGE DOWN AND THE 2” TOP AND BOTTOM
STEP TUBE BETWEEN THE SIDE PLATES.
STEP 3. ATTACH THE TOP TUBE TO THE SIDE PLATES USING THE (2) 3/8” X 1 1/4” HEX BOLTS AND LOCK WASHERS.
DO NOT TIGHTEN.
STEP 4. ATTACH THE STEP TUBE TO THE SIDE PLATES USING THE (4) 3/8” X 1” BUTTON HEAD BOLTS AND LOCK
WASHERS. DO NOT TIGHTEN.
STEP 5. POSITION THE CENTER PLATE BETWEEN THE GRILLE GUARD SIDE PLATES, WITH THE SLOTTED
MOUNTING HOLES IN THE CENTER PLATE DOWN.
STEP 6. INSERT (2) 3/8” X 1” BUTTON HEAD BOLTS THROUGH THE HOLES IN THE SIDE PLATES AND SLOTTED HOLES
IN THE CENTER PLATE WITH THE THREADS EXTENDING INWARD AND INSTALL 3/8” FLAT WASHERS, LOCK WASHER
AND HEX NUTS. DO NOT TIGHTEN.
STEP 7. INSTALL LOCK AND FLAT WASHERS ON (2) 3/8” X 1 ¼” HEX BOLTS, AND INSERT THE BOLTS THROUGH THE
ROUND HOLES IN THE CENTER AND SIDE PLATES WITH THE THREADS EXTENDING OUTWARD.
STEP 8. TIGHTEN THE 2” TOP TUBE.
STEP 9. POSITION THE DRIVER SIDE BRUSH GUARD UP TO THE GRILLE GUARD ASSEMBLY. LOOSELY ATTACH THE
BOTTOM OF THE BRUSH GUARD TO THE GRILLE GUARD SIDE PLATE USING THE 3/8” X 1 ¼” HEX BOLT INSTALLED IN
STEP #7. ATTACH THE TOP OF THE BRUSH GUARD TO THE HOLE TOWARD THE FRONT OF THE SIDE PLATE USING
(1) 5/16” X 3/4” BUTTON HEAD BOLT, AND LOCK NUT. NOTE: THE REMAINING BOLT WILL BE INSTALLED WITH THE
UPPER BRACKET.
REPEAT THE ABOVE STEP TO INSTALL THE PASSENGERS SIDE BRUSH GUARD.
STEP 10. LOOSELY ATTACH THE DRIVER SIDE HEAD LIGHT PROTECTOR TO THE BRUSH GUARD USING (1) ¼” X ¾”
BUTTON HEAD BOLT, AND TO THE SIDE PLATE USING (2) 5/16” X 3/4” BUTTON HEAD BOLTS, AND LOCK NUTS.
REPEAT THIS STEP TO INSTALL THE PASSENGER SIDE HEAD LIGHT PROTECTOR.
3000 & 7000 SERIES STEPGUARD
COMPLETE GRILLE & BRUSH GUARD
ASSEMBLY INSTRUCTIONS
PART NO. 3160MB, 3160MC & 7160MPS 07-08 CHEVY 1500 AVALANCHE, TAHOE & SUBURBAN /4WD
Do not attempt to install this product on any ehicle other than the one it is designed for and listed abo e!

2
STEP 11. ALIGN THE GRILLE AND BRUSH GUARD ASSEMBLY, AND TIGHTEN ALL NUTS AND BOLTS.
¼” x ¾” BUTTON HEAD BOLT
5/16” X ¾” BUTTON HEAD BOLTS
5/16” X 3/4” BUTTON HEAD BOLTS
3/8” X 1” BUTTON HEAD BOLTS
OTTOM STEP TUBE
CENTER PLATE
TOP TUBE
3/8” X 1 ¼” HEX BOLT, LOCK WASHER & FLAT WASHER
3 / 3/8”HEXNUT, LOCK
&FLATWASHER
SIDEPLATE
BRUSH GUARD
HEAD LIGHT PROTECTOR
3/8” X 1” BUTTON HEAD BOLT
3/8” X 1 ¼” HEX BOLT & LOCK WASHER
5/16” LOCK NUTS

3
PACKING LIST
QTY PARTS DESCRIPTION
6 ¼” X ¾” HEX BOLTS
6 ¼” FLAT WASHERS
6 ¼” HEX NUTS
2 5/16” X 1” BUTTON HEAD BOLTS
2 5/16” FLAT WASHERS
2 5/16” LOCK NUTS
12 ½” HEX NUTS
QTY PARTS DESCRIPTION
24 ½” FLAT WASHERS
12 ½” X 1 1/2” HEX BOLTS
12 ½” LOCK WASHERS
2 1602 LOWER BRACKETS
2 1604 LOWER BRACKETS
116014AA (D) DRIVERUPPERBRACKET
116014AA (P) PASSENGERUPPERBRACKET
2 1122LP LICENSE PLATE BRACKETS
INSTALLATION
STEP 1. READ THE INSTRUCTIONS COMPLETELY.
BEGINNING WITH THE DRIVER SIDE REMOVE THE (4) SCREWS AND 5MM HEX BOLT SECURING THE FRONT FASCIA
FILLER PANEL. FIG. #1
STEP 2. LOCATE AND REMOVE THE PLASTIC TOW HOOK COVER FROM THE LOWER BUMPER FASCIA. FIG. #2
I IF EQUIPPED, REMOVE THE BOLTS AND RECOVERY HOOK.
REPEAT THE ABOVE STEPS FOR THE PASSENGER SIDE.
STEP 3. LOCATE THE TWO HOLES IN THE LEFT SIDE OF THE DRIVER SIDE FRAME RAIL.
POSITION ONE OF THE 1602 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE
SIDE OF THE FRAME USING TWO OF THE ½” X 1 ½” HEX BOLTS, FLAT WASHERS, LOCK WASHERS AND HEX NUTS.
FIG. #3 DO NOT TIGHTEN.
STEP 4. LOCATE THE SINGLE HOLE IN THE RIGHT SIDE OF THE DRIVER SIDE FRAME RAIL.
POSITION ONE OF THE 1604 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE
FRAME AND TO THE 1602 BRACKET USING TWO OF THE ½” X 1 ½” HEX BOLTS, FLAT WASHERS, LOCK WASHERS
AND HEX NUTS. FIG. #4 DO NOT TIGHTEN.
STEP 5. LOCATE THE SINGLE HOLE IN THE RIGHT SIDE OF THE PASSENGER SIDE FRAME RAIL.
POSITION ONE OF THE 1602 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE
FRAME USING ONE OF THE ½” X 1 ½” HEX BOLT, FLAT WASHERS, LOCK WASHER AND HEX NUT. DO NOT TIGHTEN.
STEP 6. LOCATE THE TWO HOLES IN THE LEFT SIDE OF THE PASSENGER SIDE FRAME RAIL. POSITION ONE OF
THE 1604 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE FRAME AND TO
THE 1602 BRACKET USING THREE OF THE ½” X 1 ½” HEX BOLTS, FLAT WASHERS, LOCK WASHERS AND HEX NUTS.
DO NOT SECURE.
STEP 7. ATTACH THE GRILLE GUARD ASSEMBLY TO THE OUTSIDE OF THE 1604 LOWER MOUNTING BRACKETS
USING THE 1/2” X 1 1/2” HEX BOLTS, FLAT WASHERS, LOCK WASHERS AND HEX NUTS. FIG. #5
DO NOT TIGHTEN
STEP 8. OPEN THE HOOD. LOCATE AND REMOVE THE SCREWS SECURING THE GRILLE TO THE RADIATOR
SHROUD.
STEP 9.ATTACH 16014AA (D) UPPERBRACKETTOTHERADIATORSHROUDUSINGTHEFACTORSCREWANDTOTHE
GRILLE GUARD SIDE PLATE USING THE 5/16” X 3/4” BUTTON HEAD BOLT, FLAT WASHER AND LOCK NUT. FIG. #6 &
FIG. #7 DO NOT TIGHTEN.
REPEAT THE ABOVE STEP FOR THE PASSENGER SIDE BRACKET.
STEP 10. ALIGN THE GRILLE GUARD ASSEMBLY WITH THE FRONT OF THE VEHICLE AND TIGHTEN ALL MOUNTING
NUTS AND BOLTS. REATTACH THE FASCIA FILLER PANELS.
IF YOUR STATE LAW REQUIRES A FRONT LICENSE PLATE, ATTACH THE 1122LP BRACKETS, AND LICENSE PLATE TO
THE GRILLE GUARD CENTER PLATE USING THE ¼” HEX BOLTS, WASHERS AND NUTS. FIG. #8
3000 & 7000 SERIES STEPGUARD
COMPLETE GRILLE & BRUSH GUARD
INSTALLATION INSTRUCTIONS
PART NO. 3160M & 7160M 07-08 CHEVY 1500 AVALANCHE, TAHOE & SUBURBAN /4WD
Do not attempt to install this product on any ehicle other than the one it is designed for and listed abo e!

4
FIG #1 FIG #2
FIG #3 FIG #4
FIG #5 FIG #6
FIG #8
FIG #7
FASCIA FILLER PANEL RECOVERY HOOK COVER
1602 LOWER BRACKET
½” X 1 ½” HEX BOLTS, WASHERS & NUTS
½” X 1 ½” HEX BOLTS, WASHERS & NUTS
16014AA (D) UPPERBRACKET
5/16” X 1” BUTTON HEAD BOLT, WASHER & LOCK NUT
FACTORY SCREW
1604 LOWER BRACKET
½” X 1 ½” HEX BOLTS, WASHERS & NUTS
1601D UPPER BRACKET
1122LP LICENSE PLATE BRACKETS
¼” X ¾” HEX BOLTS, WASHERS AND NUTS
1604 LOWER BRACKET