Go Rhino D361291 User manual

QTY PARTS DESCRIPTION
10 3/8” X 1 ¼” T-BOLTS
20 3/8” X 1 1/4” HEX BOLTS
30 3/8” HEX NUTS
30 3/8” LOCK WASHERS
42 3/8” FLAT WASHERS
1D361291D DRIVER SIDE STEP
1D361291P PASSENGER SIDE STEP
1498302 DRIVER FRONT BRACKET
1498362 DRIVER FRONT SUPPORT BRACKET
QTY PARTS DESCRIPTION
1498502 DRIVER REAR BRACKET
1498562 DRIVER REAR SUPPORT BRACKET
1498304 PASSENGER FRONT BRACKET
1498364 PASSENGER FRONT SUPPORT BRACKET
1498504 PASSENGER REAR BRACKET
1498564 PASSENGER REAR SUPPORT BRACKET
2498124 DRIVER & PASSENGER CENTER BRACKETS
PASSENGER SIDE FRONT MOUNTING AND SUPPORT BRACKET
STEP-1 LOCATE AND REMOVE THE TAPE COVERING THE OBROUND HOLE IN THE BODY
ROCKER PANEL.
STEP-2 ATTACH 498304 PASSENGER FRONT MOUNTING BRACKET TO THE BODY ROCKER
PANEL USING THE 3/8” T-BOLT, WASHERS AND HEX NUT AS SHOWN.
FODI7.003.I
1
INSTALLATION INSTRUCTIONS
DOMINATOR III SERIES SIDE STEPS PART NUMBER D361291 (B)
06-09 DODGE RAM 1500, 2500, 3500 MEGA CAB P/U 4DR 2/4WD
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above!
PARTS LIST

STEP-3 LOCATE THE SQUARE HOLE IN THE UNDERSIDE OF THE BODY AT THE FRONT OF THE
CAB.
STEP-4 ATTACH 498364 PASSENGER SIDE FRONT SUPPORT BRACKET TO THE UNDER SIDE OF
THE BODY AND TO THE FLANGE OF THE MOUNTING BRACKET USING THE 3/8” T-BOLT, 3/8” X 1
1/4” HEX BOLTS, WASHERS AND NUTS AS SHOWN.
PASSENGER SIDE CENTER MOUNTING BRACKET
STEP-5 LOCATE AND REMOVE THE TAPE COVERING THE OBROUND HOLE IN THE BODY
ROCKER PANEL.
STEP-6 ATTACH ONE OF THE 498124 CENTER MOUNTING BRACKETS TO THE BODY ROCKER
PANEL USING THE 3/8” T-BOLT, WASHERS AND NUTS AS SHOWN.
FODI7.003.I
2

PASSENGER SIDE REAR MOUNTING BRACKET AND SUPPORT BRACKET
STEP-7 LOCATE AND REMOVE THE TAPE COVERING THE OBROUND HOLE IN THE BODY
ROCKER PANEL.
STEP-8 ATTACH 498504 PASSENGER SIDE REAR MOUNTING BRACKET TO THE BODY ROCKER
PANEL USING THE 3/8” T-BOLT, WASHERS AND NUTS AS SHOWN.
STEP-9 LOCATE THE SQUARE HOLE IN THE UNDERSIDE OF THE BODY AT THE REAR OF THE
CAB
STEP-10 ATTACH 498564 PASSENGER SIDE REAR SUPPORT BRACKET TO THE UNDER SIDE OF
THE BODY AND TO THE FLANGE OF THE MOUNTING BRACKET USING THE 3/8” T-BOLT, 3/8” X 1
1/4” HEX BOLTS, WASHERS AND NUTS AS SHOWN.
FODI7.003.I
3

STEP-11
ATTACH THE PASSENGER SIDESTEP TO THE MOUNTING BRACKETS USING THE 3/8” X
1 1/4” HEX BOLTS, WASHERS AND NUTS.
STEP-12 ALIGN THE SIDESTEP WITH THE BODY AND THEN TIGHTEN ALL MOUNTING NUTS AND
BOLTS.
STEP-13 REPEAT THE ABOVE STEPS FOR THE DRIVER SIDE BRACKETS AND SIDESTEP.
FOR TECHNICAL OR WARRANTY INFORMATION CALL:
TOLL FREE [phone] FAX [phone]
GO RHINO! Products® 591 W. Apollo St. Brea, CA 92821
FODI7.003.I
4