Godex ZX1000i Series User manual

ZX1000i Series
ZX1000Xi Series
THERMAL LABEL PRINTER
USER MANUAL
User Manual: ZX1000i Series
Version : 2.3
Issue Date : 2021/11/24
P/N : 920-015111-00

目錄
1 Barcode Printer ....................................................................................................................................................................................................................................5
1.1 Box content............................................................................................................................................................................................................................5
1.2 Getting to Know Your Printer..............................................................................................................................................................................................6
2 Printer Setup..........................................................................................................................................................................................................................................8
2.1 Loading the label roll ..........................................................................................................................................................................................................8
2.2 Loading & Removing the Ribbon....................................................................................................................................................................................12
2.3 Connecting the Printer to the Host Computer.............................................................................................................................................................14
2.4 Installing Printer Driver and GoLabel with Super Wizard CD....................................................................................................................................15
3 Printer Setting and Control ..............................................................................................................................................................................................................20
3.1 Operation Panel .................................................................................................................................................................................................................20
3.2 LCD Interface Introduction...............................................................................................................................................................................................21
3.3 LCD Interface Function .....................................................................................................................................................................................................26
3.4 Label Calibration and Self Test .......................................................................................................................................................................................33
3.5 Error Alerts ............................................................................................................................................................................................................................35
3.6 USB Host ................................................................................................................................................................................................................................37
4 NetSetting for Ethernet......................................................................................................................................................................................................................39
4.1 Installing the NetSetting software...................................................................................................................................................................................39
4.2 The Interface of NetSetting ..............................................................................................................................................................................................40
5 Preparation Steps ..............................................................................................................................................................................................................................47
5.1 Preparation Steps ...............................................................................................................................................................................................................47
5.2 Installing the Cutter............................................................................................................................................................................................................48
6 Maintenance and Adjustment.......................................................................................................................................................................................................51
6.1 Installing / removing the print head module ..............................................................................................................................................................51
6.2 Adjusting the print line ......................................................................................................................................................................................................52
6.3 Adjusting ribbon tension...................................................................................................................................................................................................53
6.4 Cleaning the thermal print head....................................................................................................................................................................................54
6.5 Adjusting the balance and print head tension ..........................................................................................................................................................55
6.6 Ribbon shield settings........................................................................................................................................................................................................56
6.7 Cutter settings .....................................................................................................................................................................................................................57
6.8 Troubleshooting ..................................................................................................................................................................................................................58
APPENDIX─PRODUCT SPECIFICATIONS............................................................................................................................................................................................59
APPENDIX-INTERFACE ..........................................................................................................................................................................................................................62
APPENDIX-Parallel module or Applicator module installation diagram ................................................................................................................................64
APPENDIX─Label Dispenser & Liner Rewind Module Installation..............................................................................................................................................66
APPENDIX ─Bluetooth & WiFi Module Installation ......................................................................................................................................................................67
APPENDIX ─Wi-Fi setting...................................................................................................................................................................................................................68
APPENDIX─Wi-Fi Printer Sever Module Installation(Quick Setting)...........................................................................................................................................74
APPENDIX ─Liner Rewind Operation .............................................................................................................................................................................................80
APPENDIX ─Installation Guide for Perforation Cutter................................................................................................................................................................82
APPENDIX─Installation Guide for Paper Card Cutter...................................................................................................................................................................84
APPENDIX ─High-Speed Cutter (MK147) Installation Guide ...................................................................................................................................................86

ZX1200i/ZX1200Xi Series
FCC COMPLIANCE STATEMENT
FOR AMERICAN USERS
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received,including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
TO WHICH THIS DECLARATION RELATES
IS IN CONFORMITY WITH THE FOLLOWING STANDARDS
European Standard EN55032:2012/AC:2013 , EN55024:2010. CFR 47, Part 15B
FCC CFR Title 47 Part 15 Subpart B:2013 Class B,CISPR 22:2008 ANSI C63.4: 2009
ICES-003 Issue 5:2013 Class B EN55022:2010+AC:2011,Class B EN61000-3-2 : 2006+A2: 2009
EN61000-3-3:2013 AS/NZS CISPR 22: 2009+A1:2010 EN 55024: 2010
IEC61000-4-2 Ed. 2.0: 2008 IEC 61000-4-3 Ed. 3.2: 2010 IEC 61000-4-4 Ed.3.0:2012
IEC 61000-4-5 Ed.2.0:2005 IEC 61000-4-6 Ed.4.0:2013 IEC 61000-4-8 Ed.2.0:2009
IEC 61000-4-11 Ed.2.0:2004
IEC 62368-1:2014

SAFETY INSTRUCTIONS
Please read the following instructions carefully.
1. Keep the equipment away from humidity.
2. Before you connect the equipment to the power outlet, please check the voltage of the power source.
3. Make sure the printer is off before plugging the power connector into the power jack.
4. It is recommended that you connect the printer to a surge protector to prevent possible transient
overvoltage damage.
5. Be careful not to get liquid on the equipment to avoid electrical shock.
6. For safety and warranty reasons, ONLY qualified service personnel should open the equipment.
7. Do not repair or adjust energized equipment under any circumstances.
Caution
**** Danger of explosion if battery is incorrectly replaced. Replace only with the equivalent type recommended by the manufacturer.
**** Dispose of used batteries according to the manufacturer’s instructions.
**** Only use with designated power supply adapter model.
**** Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
Specifications are subject to change without notice.

1 Barcode Printer
1.1 Box content
Please check that all of the following items are included with your printer.
(Package content and Logo style may vary per region.)
•Barcode Printer
•Label Stock •USB Cable •Quick Guide
•Ribbon •Power Cord

Feed slot for continuous labels
Ethernet port
Calibration button
Parallel port(OPTION)
Serial port (DB-9)
Applicator Interface(OPTION)
USB port
USB Host
Power jack
On/Off switch
1.2 Getting to Know Your Printer
Device Overview
•Front View
•Rear View
Stylus pen
Touch panel
Feed button
Lower cover plate
Printer cover
Viewing window
Power button
USB Host

Ribbon rewind hub
Ribbon supply hub
Release lever for print head
Print mechanism
Platen roller
Paper guide
Label tension guide
Label roll guide
Label supply hub
Adjustable Sensor
Paper guide
•The Internal View of Printer

Place the printer on a flat surface and open
the printer cover
Turn it anticlockwise to a top right position as shown in the illustration
2 Printer Setup
2.1 Loading the label roll
This printer supports the following printing methods:
Thermal transfer printing (TTP)：Requires a ribbon for transferring a printed image to a medium.
Direct thermal printing (DTP)：Does not require a ribbon, only thermal paper.
Please check which printing method you are using and alter the settings accordingly in the printer driver, printer menu, and/or software.

Now slide the label roll guide forward
and fold it down
Place the label roll on the label supply hub,
pushing it right up to the printer housing.
(Do not apply too much pressure to avoid
damaging the label stock.)
Note
————————————————————————————————————————
* When moving the label roll guide, hold it only by the end that is attached to the bracket, not by its top.

Load the label roll into the printer as shown in the illustration.
Pass it through the printer as indicated by the red arrows.
Pass the label stock through the Adjustable Sensor and up
to the tear-off plate.
Note
——————————————————————————————————————
* Remember to set the movable sensor to gap, black mark, or tag hole by changing the position of the sensor with the adjustment wheel.

1. The labels pass between the wall of the printer housing and the adjustable paper
guide.
2. Return the print head release lever to its original position.
Then close the printer cover.

Place the printer on a flat surface and open
the printer cover
Place a new ribbon on the ribbon supply hub.
The two illustrations as below show you how to install the ribbon depending on the ribbon type (ink side in or out).
Ink side out
Ink side out
2.2 Loading & Removing the Ribbon
Loading Ribbon

Pass the ribbon under the print head and back up on the other side.
Attach it to the empty ribbon core.
Note
——————————————————————————————————————
* Do not pass the ribbon under the sensor.

2.3 Connecting the Printer to the Host Computer
1. Please make sure that the printer is switched off.
2. Connect the power cord to the AC adapter and connect the adapter to the printer.
3. Connect the USB cable to the printer and host computer.
4. Switch on the printer. The operator panel should now light up.
ZX1200i / ZX1300i / ZX1600i BARCODE PRINTER

2.4 Installing Printer Driver and GoLabel with Super Wizard CD
1. Insert the Super Wizard CD in the CD/DVD drive of the host computer and the program should pop up automatically.
You will see the Welcome screen first. On the Welcome screen, choose “Standard Installation”.
2. The wizard will then ask you to make sure your USB and power cables are connected and that the power is turned on. Make sure
that is done and then click “Next”.
3. The next screen you will see to choose “Download the latest version from GoDEX server” or “Install from this
product disc.”

4. As the printer driver and GoLabel are installing, a screen will display a progress bar.
5. Once the installation is complete, you can start to make and print labels with GoLabel or through the printer driver.
6. As the optional steps, you can also print a test label or register your printer during the “Standard Installation”procedure.
Note
——————————————————————————————————————
* If you need more resources, tools or reference documents, you can also find them on Super Wizard CD.
Just click “Other Choices” on Welcome Screen to access the files.

Installing Printer Driver Directly from CD Folder
1. Insert the product CD in the CD/DVD drive of the host computer and open the "Seagull Drivers" folder on the CD.
Select the icon for the driver file and click it to start the installation.
2. Follow the instructions on the screen. The Driver Wizard guides you through the installation procedure.Select "Install printer drivers"
3. Specify your printer model.

4. Specify the port used to connect the printer to the host computer.
5. Enter a printer name and assign the appropriate rights.
6. Once the installation is complete, a summary of the printer settings is displayed.
Check whether the printer settings are correct and click "Finish" to start copying the driver files.
Wait until copying is complete, then finish the installation.

7. Once the driver installation is complete, the new printer should appear in the "Printers and Faxes" folder.

3 Printer Setting and Control
3.1 Operation Panel
POWER Button
Press the POWER button to turn on the printer, and the START UP SCREEN appears. The printer is on “ready to print”
status, the LCD screen should display the message “READY“ on the screen.
When printer is turned on, hold and press down the POWER button for 3 second will turn the printer off.
FEED Button
Turn on the printer and press the FEED button.
When you press the FEED button, the printer will advance media until the FEED button is released.
If you are using continuous labels, pressing the FEED button will advance a length of media until the button is released.
If you are using media with gaps, pressing the FEED button once will advance only one label.
If the label does not stop at the correct position, you need to run the auto-detection function for your media,
please see Section 3.4 Label Calibration and Self-Test.
PAUSE PRINTING_FEED Button
Pressing the FEED button while the printer is in standby mode will set the printer to pause mode. In this mode, the printer can receive
commands, but it will only process them when it is reset to standby mode. Pressing the FEED button again will reset the printer to standby
mode.
Pressing the FEED button during printing will interrupt printing. When the FEED button is pressed again, the printer resumes printing. Example:
While a 10-label print job is running, you press the FEED button to pause the printer.
Two of the labels have been printed. To resume printing and print the remaining eight labels, you will need to press the FEED button again.
CANCEL PRINTING_FEED Button
Press and hold the FEED button for 3 seconds during printing cancels a print job. The current print job is cancelled.
Example: While a 10-label print job is running, you press the FEED button. Two of the labels have been printed.
The print job is cancelled and the remaining eight labels will not be printed.
OPERATION
TOUCH PANEL
TOUCH PANEL
POWER BUTTON
FEED BUTTON