gofanco DP14MST2HD User manual

DisplayPort 1.4 MST 2-Port
HDMI Hub
User's Guide
G4-0140A
P/N: DP14MST2HD

2
Thank you for purchasing from gofanco. Our
products aim to meet all your connectivity needs
wherever you go. For optimum performance
and safety, please read the instructions carefully
and keep this User’s Guide for future reference.
If you need more information about our
products, please visit www.gofanco.com. For
technical support, please email us at
[email protected]. For drivers/manuals
download, please go to www.gofanco.com/
downloads.
Important Safety Notices
Please read safety instructions carefully before
installation and operation.
• Please pay close attention to all warnings
and hints for this device
• Do not expose this unit to rain, heavy
moisture, or liquid
• Do not repair the device or open the
enclosure without professional guidance
to avoid electric shocks. Doing so may void
your warranty
• Keep the product in a well-ventilated
location to avoid damage from overheating

3
Introduction
gofanco DisplayPort 1.4 MST 2-Port HDMI Hub
enables you to connect with 2 external monitors
to your DisplayPort enabled computer.
PackageContents
•DisplayPort 1.4 MST 2-Port HDMI Hub
•Micro-USB Power Cable
•User's Guide
System Requirements
•PC with an available DisplayPort output
(DP 1.4 recommended)
•Windows®11 /10 / 8.1 / 8 / 7 (32-/64-bit)
Important Notes:
•DisplayPort 1.4 GPU output is required to
support two displays up to 4K @60Hz
•DisplayPort 1.2 GPU output only supports
two displays up to 4K @30Hz
•macOS does NOT support MST function
and will only mirror the displays
•Most Intel GPU's (video cards) are limited
to 3 external displays altogether, including
the displays connected to the MST hub

4
Product Layout
Figure 1: Layout
•DP IN:Connect to PC's DisplayPort
•HDMI Output (x2):Connect to HDMI
displays with HDMI cables (not included)
•Power Jack (Micro-USB):Connect to a USB
3.0 port or 5V/1A to 5V/2A wall charger for
power with the included Micro-USB power
cable.*Note: This connection is required to
power this adapter.
Power Jack (Micro-USB)*
DP IN
HDMI Output (x2)

5
Hardware Installation
Important:If the source DP output doesn't
support DP 1.2/1.4, the Multi Stream Transport
function will be disabled and this hub becomes
a Splitter, mirroring your video source across all
displays.
1. Power off all devices you plan to connect to
the unit.
2. Connect the unit to your PC's DisplayPort
connector.
3. Connect your HDMI monitors to the unit's
HDMI Outputs with HDMI cables (not
included).
4. Connect the unit's Power Jack to a USB 3.0
port or 5V/1A to 5V/2A wall charger for
power with the included Micro-USB power
cable. Note: This connection is required to
power the adapter.
5. Power on all of the connected devices.
6. The MST hub is ready for use.

6
Connection Diagram
Specifications
Hardware
Output Signal HDMI
Output Ports 2 HDMI
Audio Output LPCM 7.1
Compli ance DP 1.4
HDMI compliant
Connectors
Input: 1x DisplayPort, Male
Output: 2x HDMI, Female
Power Jack: Micro USB, Female, 5V/900mA to 5V/2A
Cable Length 6 inches (150mm)
Video Resolution
Windows (MST mode)
DP 1.4: Up to 3840x2160 @60Hz (single or dual displays)
DP 1.2: Up to 3840x2160 @60Hz (single display);
3840x2160 @30Hz (dual displays)
Environmental Con ditions
Operating Temperature 32 to 158 F (0 to 70 C)
Storage Temperature 14 to 131 F (-10 to 55 C)
Humidity 0% to 85% RH (no condensation)
Figure 2: Connection Diagram

7
Disclaimer
The product name and brand name may be
registered trademarks of related manufacturers.
TM and ® may be omitted on the user’s guide.
The pictures on the user’s guide are just for
reference, and there may be some slight
differences with the actual products.
We reserve the right to make changes without
prior notice to a product or system described
herein to improve reliability, function, or design.

Thank you for choosing gofanco
www.gofanco.com