gofanco HDRswitch5P User manual

5x1 HDMI 2.0 HDR Switch
User's Guide
G4-0059A
P/N: HDRswitch5P

2
Thank you for purchasing from gofanco. Our
products aim to meet all your connectivity needs
wherever you go. For optimum performance
and safety, please read the instructions carefully
and keep this User’s Guide for future reference.
If you need more information about our
products, please visit www.gofanco.com. For
technical support, please email us at
[email protected]. For drivers/manuals
download, please go to www.gofanco.com/
download.
Important Safety Notices
Please read safety instructions carefully before
installation and operation.
• Please pay close attention to all warnings
and hints for this device
• Do not expose this unit to rain, heavy
moisture, or liquid
• Do not repair the device or open the
enclosure without professional guidance
to avoid electric shocks. Doing so may void
your warranty
• Keep the product in a well-ventilated
location to avoid damage from overheating

3
• Shut off power and make sure environment
is safe before installation
• Do not plug the HDMI cables in/out when
the device is in use to avoid cable damage.
Make sure they are plugged into the correct
ports
• UsetheincludedDC5Vpoweradapteronly.
Makesurethe specification matches if using
3rd-party DC power adapters
Introduction
The 5x1 HDMI 2.0 HDR Switch allows you to
selectandswitchbetween5HDMIsourcedevices
to display on 1 HDMI display.
Features
• Allows 5 HDMI source devices to be
switched/routed to 1 display
• Supports 4K @60Hz YUV 4:4:4, HDR, 3D
• Included IR remote control allows you to
select and switch source devices
• Compliant with HDMI 2.0, HDCP 2.2 with
18Gbps bandwidth

4
PackageContents
• 5x1 HDMI 2.0 HDR Switch
• Remote controller
• Power adapter
• User's guide
Installation Requirements
1. HDMI source device (computer, DVD
player, XBOX, PS3, etc)
2. HDMI display device (SDTV/Monitor,
HDTV/Monitor, projector, etc.)
3. HDMI cables

5
Layout
Figure 1: Switch
Power LED IR Window
Input LED Device Selection
HDMI Output
HDMI Input RS232
Power Jack
Power LED Lights up when the switch is powered on
Input LED Displays the selected HDMI source device
IR Window Receives commands from the included
remote controller
Device Selection Press the button to change source device
HDMI Output Connects to your HDMI display device
HDMI Input Connects to your HDMI source devices
RS232 Connects to an RS232 enabled computer for
device control
Power Jack Connects to the included power adapter

6
Hardware Installation
1. Power off all devices including your HDMI
source and HDMI display(s).
2. Connect your HDMI source devices to the
Switch'sHDMIInputconnectorswithHDMI
cables (HDMI cables not included).
3. Connect your HDMI display to the Switch's
HDMIouput connector with an HDMIcable
(HDMI cable not included).
4. Plug the included power adapter into the
Switch's Power Jack, then plug the power
adapter into a reliable power source.
5. Power on all connected devices.
6. The Switch is ready for use.
1
2
3
Remote Controller
Figure 2: Remote Controller
1. Power Button Powers On / Off
the Switch
2. Left and Right
Selects the
source device in
numerical order
3. Device Selection
Press the number
button to select
the source device
as needed

7
Connection Diagram
HDMI Switch
Power
Adapter
Computer
Display
DVD
DVD
DVDDVD
DVD
RS232 Operation
Use an RS232 terminal program such as PComm
or Hyperterminal. The examples shown are
using PComm terminal program.
1. Connect the switch to your computer using
an RS232 cable (cable not included).
2. Open your RS232 terminal program.
3. Configure the terminal program: Baud rate:
9600; Data bits: 8; Parity: none; Stop bits: 1.
See Figure 4.
Figure 3: Connection Diagram

8
Figure 4: RS232 Settings
4. In the Terminal window, type in the desired
command. See RS232 commands on the
next page.
Figure 5: Terminal Window

9
FAQ & Solutions
Q: There is no video output or audio and
video display is not normal.
A: 1) Check the power adapter connection and
make sure the Switch's Power LED is on.
2) Check whether the HDMI cables are
connected properly.
3) Check the TV is set to the correct HDMI
input.
Q: The display is unstable or pixilated.
A: 1) Check whether the HDMI cables are
connected properly.
2) Connect the HDMI source directly to the
TV for proper connection.
3) Try different HDMI cables.
Command Result
PA1R Select HDMI Input 1
PA2R Select HDMI Input 2
PA3R Select HDMI Input 3
PA4R Select HDMI Input 4
PA5R Select HDMI Input 5
ONR Power on the switch
OFFR Power off the switch
RS232 Commands

10
Specifications
Item Specification
Input ports 5x, HDMI Type-A, 19-pin, Female
Output ports 1x, HDMI Type-A, 19-pin, Female
HDMI version HDMI 2.0
HDCP version HDCP 2.2
Input resolution 4Kx2K@30/60Hz HDR, 3D, 12-bit
Full HD
Output resolution 480i/480p/576i/576p/1080i/
1080p/4Kx2K@24/25/30/60 Hz
HDR Supported
Audio Direct Stream Digital (DSD) and
HD (HBR) audio
Operating temperature 32 - 140 F (0 - 60 C)
Power consumption <5W
Dimensions 8.58" (L) x 3.10" (H) x 0.81" (W)

11
Disclaimer
The product name and brand name may be
registered trademarks of related manufacturers.
TM and ® may be omitted on the user’s guide.
The pictures on the user’s guide are just for
reference, and there may be some slight
differences with the actual products.
We reserve the right to make changes without
prior notice to a product or system described
herein to improve reliability, function, or design.

Thank you for choosing gofanco
www.gofanco.com