Goldair 3508W User manual

Operating Instructions
2400W Bathroom Wall Fan Heater
Model: 3508W, GBH100, GBH250 & GBH300

CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal safety device, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
•This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, unless they are supervised or have been given instruction
concerning the use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the
appliance.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
WARNING: You must not cover this appliance. Covering this appliance
presents fire risk and will activate the safety device; permanently disabling the
unit.
WARNING: Do not use this appliance in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless
constant supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any
flammable material a minimum distance of 1 metre from the air outlet.
•Your Goldair Bathroom Fan Heater Wall Mount must be installed with:
•At least 1.85m clearance from the floor.
•At least 210mm clearance from the ceiling.
•At least 300mm clearance on the sides.
•At least 700mm clearance from the bottom of the heater to any
obstructions, such as other appliances, shelves and pictures.
•At least 1.0m clearance from air outlet from any flammable material
including textiles, curtains and soft furnishings.
•The heater must be locked in place on the Wall Mounting Base before use for
safe operation.
•Do not place appliance close to radiant heat source.
General Care and Safety Guide
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

•Never cover this heater or restrict its airflow with a towel or any other item.
Covering or restricting the airflow of the heater will cause activation of the thermal
safety device. Do not use appliance to dry clothes.
•PLEASE NOTE: The most common cause of overheating is incorrect installation
and/or deposits of dust or fluff in the appliance. Ensure the heater is installed
correctly and/or these deposits are removed regularly by removing the heater
from the quick release wall mount and vacuum cleaning the air vents and grills.
•This appliance is intended for household use only and not for commercial or
industrial use.
•Use this appliance only as described in this manual. Any other use is not
recommended by the manufacturer and may cause fire, electric shock or injury.
•Do not use the appliance if it has been dropped or damaged.
•When the appliance has been unpacked, check it for transport damage and ensure
all parts have been delivered. If parts are missing or the appliance has been
damaged, contact the Customer Services Team.
•Do not use if there are visible signs of damage to the appliance.
•Ensure hands are dry before handling the plug or main unit.
•Do not operate this appliance with a damaged cord, plug or after the appliance
malfunctions or has been dropped or damaged in any manner. Take to a qualified
electrical person for examination, electrical service or repair.
•Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as
this may cause an electric shock, fire or damage to the appliance.
•Do not immerse in liquid or allow liquid to run into the interior of the appliance, as
this could create an electric shock hazard.
•Do not operate in areas where petrol, paint or other flammable liquids are used or
stored.
•If your appliance does not work, or is not working properly, contact the place of
purchase or the Customer Services Team.
General Care and Safety Guide

Components
Wall Mounting Plate x 1 Screw Pack:
Screw x 4
Wall Plug x 4
Main Unit x1 –3508W / GBH100 / GBH250 / GBH300

Installation Instructions
Please read these instructions and User Manual carefully.
Always choose a safe location for the heater, keeping in mind the safety precautions outlined.
Ensure all packaging has been removed from the unit before use. Do not dispose of packaging
until completely satisfied with your purchase.
THE HEATER MUST BE LOCKED IN PLACE ON THE WALL MOUNTING BASE BEFORE IT CAN BE
SAFELY OPERATED.
Bathroom fan heaters are only to be mounted on heat resistant walls that comply with current
AS/NZS specifications & building regulations. Use only the voltage specified on the rating label
of the appliance.
• It is illegal for persons other than those authorised by legislation to work on the fixed wiring
of any electrical installation.
• All installations must be in accordance with the local Electrical Wiring Regulations and Wiring
Rules.
• Means for disconnection must be incorporated in the fixed wiring in accordance with the
wiring rules
CAUTION: Do not mount directly under or above an electrical power socket. It is
recommended to install the heater to the side of any power socket
CAUTION: The appliance is to be installed so that switches and other controls cannot be
touched by a person in the bath or shower.
NOTE: Your Goldair Bathroom Fan Heater Wall Mount must be installed with:
•At least 1.85m clearance from the floor.
•At least 210mm clearance from the ceiling.
•At least 300mm clearance on the sides.
•At least 700mm clearance from the bottom of the heater to any obstructions, such
as other appliances, shelves and pictures.
•At least 1.0m clearance from air outlet from any flammable material including
textiles, curtains and soft furnishings.
CAUTION: Ensure your unit is at least 700m above any wall mounted object –this includes
window frames and doors –they may only protrude a small amount, but this can reflect
sufficient heat to cause safety devices to activate.
NEVER install unit in a position where an open door can abut up to the front of the unit, as it
will heat up too quickly and activate the safety devices.
See installation instructions on next page.

Installing your Appliance
INSTALLATION
•Select a location for mounting of the heater in accordance with the installation instructions
•The heater must be connected by permanent wiring within the wall cavity from an isolating
switch.
•Ingress Protection (IP): Bathrooms are divided into four zones based on the levels of
perceived risk within each area. The measurements are taken from the fixed plumbing
connection (water source) and each zone has specific requirements regarding the electrical
equipment that can be used within it.Goldair Bathroom heaters are rated IPX0so must
be installed in Zone 3.
•The Wall Mounting Base should be positioned as shown in Figure 1.
•The wiring within the wall cavity can be terminated into the respective terminals marked L
•and N on the wall mounting base. (See Figure 3a).
•The Wall Mounting Base must be secured with all four screw fixing points.
•Securely fix the Wall Mounting Base to the wall surface with the screws and wall plugs
•supplied. (See Figure3b).
•The Wall Mounting Base can be used with or without a flush box (Cat144) in the wall
cavity. When using a flush box it should be located directly behind the Wall Mounting Base
connector block.
•Fit the heater to the wall mounting base by ensuring the 4 hooks on the wall mounting
base have engaged with the mounting apertures of the heater. Slide the heater down to
lock it into place. The electrical connection is automatically made during this step.
•The heater must be locked in place on the Wall Mounting Base for safe operation.
•To check the heater is fully locked to the mounting base, attempt to gently slide the heater
upwards. It should be securely held in position.
•To remove the heater from the Wall Mounting Base insert a blade screwdriver into the
hole located below the middle of the outlet grille. Rotate the screwdriver until the clip
releases. Then while holding the heater, gently push up with the screwdriver sliding the
heater off the Wall Mounting Base. (See Figure 2.)
•Please refer to your user manual for operating instructions, further information or trouble
shooting before you call the Customer Service number listed within the user manual.

Operating Your Heater
WARNING:In order to avoid overheating or fire, DO NOT COVER the heater.
WARNING:Do not use this heater with a programmer, separate timer, remote-
control system or any other device that switches the heater on automatically, as a
fire risk exists if the heater is covered or positioned incorrectly.
WARNING:Never leave this heater unattended when in use.
NOTE: When the appliance is turned on for the first time, it may release a slight
odour or smoke. This odour or smoke is a normal occurrence caused by the initial
heating of the internal heating elements and should not occur again.
IMPORTANT NOTE:
Goldair bathroom heaters have 3 operating modes:
Heat Control –Hot Air –2400W
Ensure the heater has power available by turning it on at the isolating switch. Pull the pull-
cord to start the heater. The neon indicator light will illuminate indicating the heater is in
operation. Pull the pull-cord again to turn the heater off.
Automatic Step-down Heat –Warm Air –1200W
When the room reaches a pre-set temperature, the heater will automatically step-down and
reduce the heat output to save power. If the room cools down, the heater will automatically
step-up and increase the heat output.
Overheat Protection –Cold Air
The heater will turn itself off in the event of over heating. The most common cause of over
heating is deposits of dust or fluff entering the appliance. Ensure these deposits are removed
regularly by cleaning the inlet and outlet grills. The heater will automatically re-set when it
has cooled down.
If the heater is blowing cold air, power it off and leave it for 1-2 hrs to allow the safety
devices to cool down and reset. Then reactivate your heater and if;
A) it blows warm or hot air, continue to use the heater.
B) it still blows cold air, then the permanent disabling
element safety device has activated. You will need to
reach out to CDB customer services team with imagery
of your installation and we will be in touch with further
instructions. Scan the QR-Code to be directed to our
contact us website page.

Cleaning Your Heater
The heater requires regular cleaning to ensure trouble free operation:
•Before cleaning, remove unit from Mounting Base Plate.
•Use a vacuum cleaner to remove dust and fluff from the inlet and outlet grills.
•Use a damp cloth to clean the exterior of the heater. Do not use abrasive
cleaning products on this appliance.
•Ensure the heater is dry before turning the power supply back on to the heater.
Servicing Your Heater
Do not attempt to repair or adjust any electrical or mechanical functions on this
unit. Doing so will void the warranty. Contact a qualified electrical person to
service the heater.

Thank you for purchasing this Goldair product. Your product is warranted against faults and manufacture when used in normal
domestic use for a period of one year. In non-domestic use Goldair limits the voluntary warranty to three months.
Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the
warranty period.
This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone
other than a qualified electrical service technician.
PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.
The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the
goods or services to which this warranty relates.
In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993).
One Year Warranty
Goldair One Year Warranty (IMPORTANT: Please complete and retain this warranty card)
Name
Address
Place Of Purchase Date Of Purchase
Name Of Product Model Number
Attach a copy of the purchase receipt to this warranty card
Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product.
Goldair –New Zealand
CDB Goldair
PO Box 100-707
N.S.M.C
Auckland
Phone [phone]
Phone [phone]
www.goldair.co.nz
Goldair –Australia
CDB Goldair Australia Pty
PO Box 574
South Morang
Victoria, 3752
Phone [phone]
Phone 1300 GOLDAIR (1300 465 324)
www.goldair.com.au

New Zealand
PO Box 100707,
North Shore Mail Centre,
Auckland, 0745
www.goldair.co.nz
Australia
PO Box 574,
South Morang,
Victoria, 3752
www.goldair.com.au