Goldmedal 2410 Series User manual

© 2021 Gold Medal Products Co.
Part No. 110282
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
RH & LH Digital Mark 10
Corn Treat Units
Model No. 2410 Series
Instruction Manual

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 2
gmpopcorn.com
Table of Contents
SAFETY PRECAUTIONS ...................................................................................................................................3
INSTALLATION INSTRUCTIONS ...................................................................................................................5
Inspection of Shipment ..........................................................................................................................................5
Manual...........................................................................................................................................................................5
Model Description ....................................................................................................................................................5
Items Included with this Unit..............................................................................................................................5
Setup...............................................................................................................................................................................6
Paddle and Drum Assembly ...........................................................................................................................6
Electrical Requirements ........................................................................................................................................7
Before You Plug In Machine.................................................................................................................................8
OPERATING INSTRUCTIONS .........................................................................................................................9
Controls and Their Functions..............................................................................................................................9
Adjusting the Set Temperature ....................................................................................................................... 10
Making Caramel Corn ............................................................................................................................. 11
Care and Cleaning .................................................................................................................................... 12
Kettle Cleaning Procedure................................................................................................................................. 12
Daily Unit Cleaning Procedure......................................................................................................................... 13
Weekly Cleaning of the Hub Seal Assembly ............................................................................................... 13
Troubleshooting....................................................................................................................................... 15
MAINTENANCE INSTRUCTIONS ................................................................................................................ 16
New Paddle/Hub Seal Kit Installation .............................................................................................. 17
Kettle Shaft Maintenance ...................................................................................................................... 17
ORDERING SPARE PARTS............................................................................................................................ 18
Cabinet Exterior and Handle Assembly ....................................................................................................... 19
Kettle and Drum – Parts Breakdown ............................................................................................................ 21
Kettle Bottom – Parts Breakdown.................................................................................................................. 23
Control Box Interior and Exterior .................................................................................................................. 25
Safety Labels ............................................................................................................................................................ 26
Accessories ............................................................................................................................................................... 26
Wiring Diagram ........................................................................................................................................ 27
WARRANTY...................................................................................................................................................... 28

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 3
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.
013_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 4
gmpopcorn.com
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note:Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at 1-800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or
reckless operation of this equipment.) General images may be used in manual for
reference only.

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 5
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
Digital Mark 10 Corn Treat Unit:
•10 gallon capacity
•Either right hand or left hand dump capability
•Either straight handle or upright handle—upright handle model mounts on a 2436-001
short base (sold separately) when used with a 2169 series lift table (sold separately.)
2410-00-100: Right hand dump, straight handle
2410-00-110: Left hand dump, straight handle
2410-00-102: Right hand dump, upright handle
2410-00-112: Left hand dump, upright handle
Items Included with this Unit
10 Gallon Measure
(PN 46508)for popped corn
30A Receptacle
(PN 82208)
Bowl Scraper
(PN
46210)
2 Cup
Measure
(PN 62807)
Aluminum Scoop
(PN 2071)
2 included with unit
8 Cup
Measure
(PN 69826)
Instruction
Manual
Registration
Warranty Card

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 6
gmpopcorn.com
Setup
1. Remove all packaging and tape, and accessories before starting operation.
2. This unit must be properly fastened to a sturdy counter or base, see illustration below for
mounting requirements.
Paddle and Drum Assembly
1. Prior to operation, rotate the top paddle from the shipping position into the mix
position—reference images on next page for paddle and drum assembly:
a) Pull plunger knob out and lift paddle into position.
b) When positioned, release knob and make sure the plunger securely sets into its
hole in the shaft to lock the paddle in place.
2. After setup, the unit should be cleaned prior to use (see Care and Cleaning section).
2” Dia. X 1/8” Thick
Fender Washer
3/4” Minimum
for Wood or
Wood Plastic
Products
5/16-18
Grade 5 Bolt
3/16” Minimum
Thickness for
Stainless Steel
Over Wood
5/16-18
Grade 5
Nut
3” Minimum Clearance
b
etween Kettle and Wall.
4 Holes for
5/16” Dia. Bolts
6 .50”
2.00”
17.375”
19.375”
15.585”
6” Recommended Min. Clearance
between Wall and Cntl Box for
Service.
48.00”
27.35”
39.66”
20.375”
19.00”
3” Min. Clearance
b
etween Kettle
and Wall
.
20.903”

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 7
gmpopcorn.com
Electrical Requirements
The following power supply must be provided (reference unit Data Plate for Wattage requirement):
120/208 or 120/240 V~, 60 Hz
Unit is designed to operate on single phase, 30 AMP, 4 wire supply, 120/208 or
120/240 V~ (2 Hot, 1 Neutral, 1 Ground). All electrical components in this machine are
120 V (motors, heat elements, lights, etc.) and therefore require “Hot to Neutral”
connection (NOT “Hot to Hot”). A wall receptacle is supplied with the machine. This
receptacle will accept the attachment plug on the machine and must be used.
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
Corn Treat
Paddle
Kettle
Bottom
Plunger
(
plunger must
securely set in
hole in shaft)
Plunger
Knob
Mixing Drum
Retaining Ring
Drum Seal
Drum seal fits
around bottom
lip of drum
.
Paddles Shown in Mixing Position
Fasten or Adjust Retaining Ring Latch
1. Open latch then fit
retaining ring over
drum and kettle rims.
2. Place hook
in first slot.
4. To adjust hook length, loosen nut,
adjust hook in or out, then retighten nut.
3. Push clasp tight to kettle to lock
retainer in place.

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 8
gmpopcorn.com
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage
requirements). We recommend this equipment be on a dedicated and protected circuit. Failure
to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal
Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of
extension cords is not recommended due to safety concerns, and may cause sacrificed and/or
reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Receptacle Installation for L14-30
A certified electrician must follow the IMPORTANT instructions below for installation of the
L14-30 Receptacle (Gold Medal Item No. 82208) provided with the unit.
If the receptacle is wired incorrectly, the heat elements/kettle and other electrical components
could be at 208 or 240 V potential instead of the needed 120 V, resulting in excessive temperatures
in the heat elements (i.e.: kettle) and possible fire, and/or damage to electrical components.
Before You Plug In Machine
1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power
supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
L14-30 Back View
Green Terminal
Connect to Green
(Ground) Wire
Brass Terminal
Connect to
Red
(
Hot) Wire
G
Y
Brass Terminal
Connect to
Black
(Hot
) Wire
Silver Terminal
Connect to
White
(Neutral
) Wire
X
W
L14-30
Front View

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 9
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
HEAT/MOTOR SWITCH
ON/OFF lighted rocker switch – provides power to the heating elements in the bottom of
the kettle and powers the agitator motor to turn for 30 seconds of every minute. The
green switch light ON indicates there is power to these features.
Note: It is normal for the motor to stop for 30 seconds of every minute (when the Motor
Only Switch is OFF).
MOTOR ONLY SWITCH
ON/OFF lighted rocker switch – provides power to the agitator motor to run continuously.
Note: The main function of the Motor Only switch is to mix the popcorn at the end of the
cooking cycle (with the kettle in the mix position); and it is used for “cleaning mode”.
CIRCUIT BREAKER
The Circuit Breaker protects the Motor and Heat Control from an overload condition.
KETTLE DUMP HANDLE
The Kettle Dump Handle tilts the kettle from the upright cook position, to the mix position
or the dump position. The 2 position bracket holds the handle in the tilted position.
DIGITAL HEAT CONTROL
The Digital Heat Control displays kettle temperature and is used to adjust the set point
temperature—unit is factory preset at 275°F (135°C). See Adjusting the Set Temperature
section to change the set point.
The buzzer sound signals kettle heat shut-off. The buzzer will continue to sound until unit
is turned off or until unit temperature falls below set point.
Control Panel View
Heat/Motor
Switch
Motor Only
Switch
Digital Heat
Control
Circuit
Breaker
Kettle Dump
Handle
2 Position
Bracket

RH & LH Digital Mark 10
Corn Treat Units Model No. 2410 Series
Page 10
gmpopcorn.com
Adjusting the Set Temperature
The Digital Heat Control is factory preset at 275°F (135°C); maximum setting is 450°F (232°C).
The set point temperature you need may vary from the preset temperature depending on your
recipe and cooking environment. Use the preset as a starting point, then adjust it to fit your needs.
To adjust the preset temperature:
1. Press “SET” button on the Digital Heat Control, and “SP” will appear. Press “SET” again
to display current set temperature.
2. Press the “UP/DOWN” arrows to adjust to the desired temperature. Press “SET” to save.
3. Press “SET” and the “DOWN” arrow at the same time to return to operating mode.
Digital Heat Control image shown for general reference only.
SET Button
UP Arrow
DOWN Arrow
Digital Display
°F or °C (Fahrenheit shown)
Heat Indicator Light (Light ON indicates unit is
heating. Light will cycle OFF/ON during operation.)