Goldmedal Hawaii's Finest1027 User manual

Part No.12205
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Hawaii’s Finest
Model No. 1027
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 2
gmpopcorn.com
SAFETY PRECAUTIONS
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 3
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control.
Setup
Your new Hawaii s Finest was completely assembled and tested at the factory. Remove all
packing material and tape before starting operation.
Electrical Requirements
1027: 120V, 840W, 60Hz
DANGER
Machine must be properly grounded to prevent electrical
shock to personnel. Failure to do so could result in serious
injury, or death.
Do NOT immerse any part of this equipment in water.
Do NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from
moisture.
Always unplug the equipment before cleaning or servicing.
Your electrician must furnish sufficient power for proper machine operation. We recommend
this shaver be on a dedicated and protected circuit. Failure to wire properly will void the
warranty and may result in damage to the machine. It is Gold Medal Products Company s
recommendation that this machine be plugged directly into a wall outlet. The use of extension
cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced
performance.
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter.
5. Make sure to leave enough room in the back of the machine to allow hookup of the
drain hose.
6. Install the unit in a level position.
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 4
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
MAIN SWITCH
Turns shaver motor “ON” or “OFF”.
RESET SWITCH
Motor overload switch.
BLADE ADJUSTMENT KNOB
Adjusts the blade height to change the ice texture.
Ice Requirements
The Hawaii s Finest can take ice cubes or block ice, if you break the block into pieces
approximately 2 to 3 inches in size.
NOTE: The ice will not enter the shaving chute if the pieces are too large.
Operation of Hawaii’s Finest
1. Allow ice to soften at least 1 hour in an ice cooler before use. Using ice straight from
the freezer affects the quality of the shaved ice as well as damage the shaver blade.
2. Lift cover lid and load ice cubes about ½ full then close the lid. Be sure ice is loaded
evenly in each cavity. Place cup directly below the ice chute and turn power “ON”.
Failure to close the lid will cause machine not to operate!
3. Adjust the blade height with the adjustment knob to achieve the preferred ice texture.
4. To stop, turn power switch to the “OFF” position. Should the motor thermal protector
trip, reset it by pushing the red button. It is recommended the cause of over load be
found and eliminated before continuing. The machine may need to cool a bit before
the reset button may take effect.
NOTE: Never allow any foreign or metallic objects around the shaver area of the Hawaii s
Finest. Ice picks, scoops, and debris that may be in the ice often damage blades.
Main Switch
R s t Switch
Blad Adjustm nt
Knob
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 5
gmpopcorn.com
CARE AND CLEANING
Cleaning Instructions
1. Remove lid by removing the wing nut and hinge pin.
2. Remove the four plastic button screws that hold top hopper cover, and lift and
roll over.
3. Disconnect wire harness at plug.
4. Remove three thumb screws and remove impeller cover.
5. Remove impeller knob, and lift impeller off. For removal of Impeller Knob a
screwdriver slot is supplied on bottom end of motor.
6. Lift off bottom plastic base cover.
7. Remove two stainless steel button screws holding chute.
8. Wipe down all easily accessible areas with a clean, dry cloth.
Blade Cleaning Instructions
1. Blade holder should be cleaned at weekly intervals. Begin removal by removing chute.
2. Using blade adjustment knob, unscrew blade adjustment shaft and remove.
3. Pull pivot pin out completely.
4. Blade, blade holder assembly and spring are now free for removal.
5. Remove the two blade retaining screws and remove blade.
6. Wipe area and parts with clean, dry cloth.
7. Assemble in opposite order as above.
The stainless steel body of the shaver can be kept clean with cleaner designed for stainless steel
and a clean cloth. We recommend Gold Medal Products Company s authentic Watchdog Stainless
Steel Polish (Part No. 2088.)
NOTE: Never use abrasives on the stainless steel body.
DANGER
Machine must be properly grounded to prevent electrical
shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
Good sanitation practice demands that all food preparation equipment be cleaned regularly. A
clean looking, well-kept machine is one of the best ways of advertising your product.
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 6
gmpopcorn.com
MAINTENANCE INSTRUCTION
DANGER
Improper installation, adjustment, alteration, service, or
maintenance can cause property damage, injury or death.
Read the installation, Operating, and Maintenance
Instructions thoroughly before installing or servicing this
equipment.
DANGER
Do Not immerse the equipment in water. Unplug your
machine before servicing.
WARNING
Adequate eye protection must be used when servicing this
equipment to prevent eye injury.
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE
INTENDED ONLY FOR QUALIFIED SERVICE
PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL
EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 7
gmpopcorn.com
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
Phone: [phone]
[phone]
Fax: [phone]
[phone]
E-mail: [e-mail]
Web Page: www.gmpopcorn.com
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 8
gmpopcorn.com
Cabinet Exterior Assembly
Part No.
1027
1 TOP COVER DOOR 1 12119W
2
TOP COVER
1
12557W
3
WING NUT 6-32 STL ST
1
12152
4 ICE CHUTE WELD ASSEMBLY 1 12683
5 BACK COVER 1 12638
6 1/2 ID SILCON TUBING 1.3 ft. 12156
7
BASE
1
12088
8 RUBBER BUMPER 2 12487
9 SUCTION CUP, 1/4-20 STUD 2 12642
10 TOP COVER KNOB 4 12112
11
HINGE PIN DOOR
1
12145
Qty.Part D scriptionIt m
1
2
3
4
5
6
7
8 9
11
10
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 9
gmpopcorn.com
Cabinet Bottom Assembly
Part No.
1027
1 1/4-20 X 1 HX HD C S 18-8 4 12185
2
5/16 FLAT WASHER, 18-8
4
12184
3 1/4-20 SERRATED LOCK NUT 4 46311
4 BOTTOM COVER STAINLESS 1 12294
5 1/2 ID SILCON TUBING 1.3 ft. 12156
6
STRAIN RELIEF #SR-6P3-4
1
76026
7 LEAD-IN CORD 15 AMP PLUG 1 12154
8 DRAIN HOSE 3/4 ID 7/8 OD 4 ft. 12159
9
HOSE CLAMP WITH SCREW
1
41163
Qty.Part D scriptionIt m
3
4
5
6
7
9
8
1, 2
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 10
gmpopcorn.com
Hopper Assembly
9
10
12
7
6
8
1
B hind Brack t
5 4 2
3
14
*Th Wat r Shi ld should con downward on
motor shaft.
17
11
15
16
13
Und r Imp ll r
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 11
gmpopcorn.com
Hopper Assembly – Parts List
Part No.
1027
1 SWITCH MOUNTING BRACKET 1 12136
2 DOOR SAFTEY SWITCH 1 12116
3 SPACER 1 12151
4 1/2 OD X 1/2 T MAGNET 1 12078
5 MOUNTING BLOCK MAGNET 1 12135
6 DOOR SAFTEY SWITCH HARNESS 1 12131
7 WIRING HARNESS BRACKET 1 12146
8 WATER SHIELD HARNESS 1 12160
9 IMPELLER 1 12090
10 IMPELLER NUT 1 12106
11 THUMB SCREW 10-32 X 3/8 6 12123
12 SPINNING HOPPER (Impeller Cover) 1 12109
13 UPPER BASIN 1 12556
14 PUSHER STUD 1 12104
15 PUSHER IMPELLER 1 12098
16 BALL BEARING F. 5/8" SHFT 1 12091
17 SHIELD - WATER 1 12097
Qty.Part D scriptionIt m
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 12
gmpopcorn.com
Shaver Assembly
Part No.
1027
1
BLADE ADJUSTMENT KNOB
1
12111
2
SET SCREW 8-32 X 1/8 S.S.
1
12165
3
BLADE ADJUSTMENT SCREW ASSEMBLY
1
12125
4 ICE CHUTE WELD ASSY 1 12683
5*
10-32 x 1/2 HOLLOW SET
*
1 12129
6
BLADE HOLDER PIN
1 12110
7
BLADE HOLDER
1 12195
8
THUMB SCREW 10-32 X 3/8 (Blade
retaining screw)
2 12158
9
SHAVER BLADE
1
12094
10
COMPRESSION SPRING
1
12117
11
STUD-SPRING RETAINER
1
12143
Qty.Part D scriptionIt m
*NOTE: Factory pre-set, DO NOT tamper with.
1
2
3
4
7
5*
8
6
9
10
11
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 13
gmpopcorn.com
Cabinet Internal Assembly
Part No.
1027
1 STRAIN RELIEF-WATER TIGHT 1 12149
2 SPST ROCKER SWITCH 1 12115
3 RESET SWITCH 1 12182
4
MOUNT BRACKET-SWITCH
1
12181
5
DRAIN TRAY UPPER BASIN
1
12553
6 MOTOR SUPPORT PLATE 1 12514
7 DRIVE MOTOR 1/3 HP 1 12194
Qty.Part D scriptionIt m
1
2
3
7
6
5
4
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 14
gmpopcorn.com
WIRING DIAGRAM
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com

Hawaii’s Finest Model No. 1027
Page 15
gmpopcorn.com
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage,
abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT
1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241
-
4807 USA
www.gmpopcorn.com
Phone:
(800) 543
-
0862
[phone]
Fax: [phone]
(513) 769
-
8500
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com