Goldmedal Sno-Pro 1800 User manual

Part No. 22132
MARCH 2008
Sno-Pro
Instruction Manual
Model #1800
Cincinnati, OH 445241-4807 USA

Sno-Pro
All Models #1800
2
Safety Precautions

Sno-Pro
All Models #1800
3
INSTALLATION
MACHINE DESCRIPTION
The Sno-Pro is an automatic shaver with a tremendous capacity. You will find that it keeps up with any
demand. The Sno-Pro consists of the hopper, which houses the band shaving blade, impeller, hopper lid,
motor, and the ice cabinet.
ELECTRICAL REQUIREMENTS
The Sno-Pro operates on 120 Volt, 15 Amp, single phase, 60 cycle AC current. Be sure that your electrical
supply meets this requirement.
ICE REQUIREMENTS
The Sno-Pro can take ice cube (small or medium in size) or small block ices, if you break the block into
pieces approximately 2 to 3 inches in size.
NOTE: The ice will not enter the shaving chute if the pieces are too large.
MACHINE OPERATION
Plug the power cord into the appropriate electrical outlet.
TO OPERATE THE SNO-PRO
1. Open the hopper lid. Fill the hopper to within an inch of the top with ice cubes or block ice (no larger
than 2" to 3"). Close the Hopper Lid.
2. Toggle the POWER switch to the ON position.
3. Press the Red Motor Button to shave. If the hopper is open the motor will not operate.
NOTE:
Never allow any foreign or metallic objects around the shaver area of the Sno-Pro. Ice picks, scoops, and
debris that may be in the ice often damage blades.
Harder ice will result in finer now, while soft ice will result in coarser snow.

Sno-Pro
All Models #1800
4
MAINTENANCE INSTRUCTIONS

Sno-Pro
All Models #1800
5
ORDERING SPARE PARTS
1. Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity desired.
3. Please include your model name and machine serial number (located on the machine nameplate) with
your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [email protected]

Sno-Pro
All Models #1800
6
INSTALLING NEW SHAVER BLADES
Inspect your equipment before replacing the blades. With the POWER switch OFF, use a flashlight
to examine the blades in the shaver body. If the blades appear to be nicked or bent, then the
blades should be replaced.
Follow this procedure:
1. Unplug the main power supply cord from the electrical outlet.
2. Remove the 5 screws holding the top cover on the unit. Slide the cover out of the way as
shown below.
3. Un – couple the quick connect on the electrical lead going to the magnetic switch.
COVER
SCREWS
QUICK
CONNECTOR

Sno-Pro
All Models #1800
7
4. Remove the 4 black thumb screws holding on the hopper to the motor plate.
5. Remove the Hopper Assembly from the Cabinet. Tilt the top of the hopper away from the
motor, and gentle guide and lift upward on the hopper until the outlet nozzle out of the cabinet.
You might have to rotate the impeller to allow for the band blade to be removed easily.
6. The Shaver band blade has 6 tabs on the exterior of the hopper. Twist the tabs to align with
the slots in the hopper. Once all 6 are aligned with the slot openings. Push the tabs thru the
slots removing the blade.
TABS
THUMB
SCREWS

Sno-Pro
All Models #1800
8
7. Re-installing new band blade, Note: the orientation of the snow guide, to the snow nozzle.
Make sure blade is in proper orientated. Push the 6 band blade tabs into the slots. Make sure
band blade rests in the bottom groove in the hopper, and seats flush on the bottom of the
groove. You may need to flex the blade to seat flush.
8. Now twist the 6 tabs to lock the band blade in place.
9. Re-Install the hopper onto the cabinet. Feeding the nozzle into the cabinet opening first. Then
tilting the top of the hopper toward the motor. Note: The impeller might need to be rotated to
allow for easily assembly.
10.Re-Install the 4 thumb screws.
11.Reconnect the electrical quick connect.
12.Reinstall the 5 screws in the top cover.
N
ote: Orientation

Sno-Pro
All Models #1800
9
MODEL 1800 ASSEMBLY
6
1
2
5
3
7
4
8
26
28

Sno-Pro
All Models #1800
10
MODEL 1800 ASSEMBLY
9
12
10
11
25
27
29

Sno-Pro
All Models #1800
11
MODEL 1800 ASSEMBLY
13
.
15
14
17
.
16
.
9.

Sno-Pro
All Models #1800
12
BAND BLADE AND HOPPER ASSEMBLY
18
23
19
20 17
21
22
24

Sno-Pro
All Models #1800
13
PARTS LIST
Model # 1800
Item No. Part No. Description
1 12726 Cabinet
2 12727 Top Cover
3 12648 Side Glass Plex
4 12650 Side Glass Plex Outlet Side
5 12798 Power Switch
6 38971 Momentary Switch
7 12698 Front Panel Plex
8 12653 Ice Stop Plex
9 12790 Motor 120 v 1/3 HP
10 12131 Wire Harness, Quick Connect Assembly
11 12731 Motor Plate Welded Asembly
12 12733 Ice Shield Plate
13 12673 Strain Relief Plate
14 76026 Strain Relief
15 74746 3" Fan Grate
16 22038 Lead-in Cord 15 Amp Plug
17 22040 Impeller (RH thread)
18 12734 Hopper Lid
19 12729 Hopper
20 12735 Hopper Electrical Cover
21 12728 Band Blade
22 12652 Hinge Pin
23 12736 Magnet Mount Block
24 12078 Magnet
25 12116 Micro Switch
26 12668 Drain Fitting
27 12687 Push In Fastener
28 22034 Hose - clear
29 12793 Knob
30 22132 Manual
31 27563 Wrench (used in removal of impeller)

Sno-Pro
All Models #1800
14
ELECTRICAL SCHEMATIC
MODEL #1800

Sno-Pro
All Models #1800
15
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage,
abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT
PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING
THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA