golmar Rock Series User manual

Video Kit
3 + coax
4 + tp
Rock Series
Installation manual
T801EN rev.0120
Cód. 50124602

INTRODUCTION 41
Introduc ........................................41tion
Safety precautions...............................42
Door panel installation.............................
Ind ................................................. 41ex
System operation.................................43
Starting recommendations................... 41
System characteristics.....................42-43
Very important note.......................... 43
Embedding box positioning................ 44
Final adjustments..............................46
Power supply .......................46installation
Descrip ...................................... 47tion
SW1 dip switch (quick prog. mode)......49
RJ-45 connector................................49
Tekna-S Plus ..............................Monitor
EL562S ................................50Module
Installing in a wall mounting connector.....51
Installing in an embedding box........... 52
Programming..............................53-54
Door panel configuration...................45
Quick programming......................... 54
Lock release installation....................... 46
End of line resistor............................. 50
Function buttons............................... 48
Communication with hearing aids.......48
Programming (monitor functions)...5 -55 8
Function push buttons........................60
Programming................................... 63
Door bell push button connection........77
Aux. devices activation T 40Plus5 SE.... 77
Telephone installation........................62
Aux. device activation Tekna Plus-S ......74
Optional connections..............................
Installation diagrams...............................
Troubleshooting.................................. 78
Compliance....................................... 79
Sections charts..................................73
Description...................................... 59
External lock release T540 Plus SE.......75
External lock release Tekna-S Plus....... 75
T-540 Plus SE Telephone...........................
Programming backbone code...............67
Video ........ 71 72system with twisted pair -
D.c. and a.c. lock release................... 73
Video ..... 69-70system with coaxial cable
External button to open the door.......... 73
2nd camera activation.......................75
Intercom..........................................76
SW1 DIP switch.................................61
Programming (telephone functions)...64-68
Quick programming......................... 64
INDEX
Its advanced technology and exacting quality control will do that customers and users enjoy with the
legion of features this system offers. To obtain the maximum profit of these features and a properly wired
installation, we kindly recommend you to expend a few minutes of your time to read this manual.
First of all we would like to thank and congratulate you for the purchase of this product manufactured by Golmar.
The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification
and for the manufacturing of products like this one.
STARTING RECOMMENDATIONS
OEach time the power supply is restarted, or after a modification, the system will remain blocked during
45 seconds.
ODo not use excessive force when tightening the power supply connector screws.
OThe entire installation must be at least . away from any .40cm other installation
OBefore to connect the system, check the connections between door panel, monitors, telephones, and
the transformer connection. Do always follow the enclosed information.
OAlways use coaxial cables, (see page ).RG-59 B/U MIL C-17 or RG-11 69 Never use coaxial
antenna cable. Golmar RAP-5130In installations no longers than 100m., cable can be used.

42
OCombinable , .with code general entrance panels up to 250 internal houses
O
.
Compatible with electronic audio systems or video systems with four common wires, three
wires+coaxial or four wires+twisted pair installations
OCompatible with Tekna Plus monitors and telephones Uno and Plus.
OMicroprocessed video system with
Uno technology.
3 wires+coaxial installation or 4 wires+twisted pair
installation without making any change on the doorpanel.
Odoor panelIP-44 sealed and anti-vandal IK-09.
OUnlimited door panel number without using commutation units.
Odoor panelMaximum distance between and monitor: 200m.
O.Phone tones to confirm call and busy line
OTemporized door opening for three seconds.
O.Direct current or alternative current lock release activated by means of a relay
OUp to two monitors and one phone in each house without extra power supply.
OIn monitorsTekna-S Plus Color / T540 Plus SE telephones:(for installation Plus/ Uno).
OD necessary to use the digital
repeater RD-Plus/Uno SE.
istance from door panel to last monitor is largest than 200 m, it will be
w(Video only monitor).Privacy on audio and video communications.
w"Autoswitch-on" function.
w. (Only monitor)."Video-spy" function with the communication channel remaining free
wPanic call to the porter's exchange.Call to a master and slave porter's exchange.
wInput for external door bell push button.
wDip switches for quick programming mode.
wIntercommunication function with other monitor o telephone of the same apartment.r
w(only monitor)Activation of two auxiliary devices: secondary telecamera , courtesy light, ...
wCall volume control (maximum, no volume 'night mode,' medium and minimum).
wNegative output for additional call repeater (maximum current 250mA).
wEnables communication with hearing aids equipped with T-mode, making conversation possible
(inductive loop). (Only monitor).
wFunction and advanced programming buttons (to customise the monitor's 's functions)./ telephone
SAFETY PRECAUTIONS
SYSTEM CHARACTERISTICS
OWith power supply:
wDo not block ventilation holes of the unit so that air can circulate freely.
OWith monitor, telephones and distributor:
ODo always follow the enclosed information.
wInstall the power supply in a dry and protected place without risk of drip or water projections.
OThe entire installation must be at least . away from any .40 cm other installation
OInstall or modify the equipment .without the power connected
OThe installation and handling of these equipments must be performed by .authorised personnel
wDo not use excessive force when tightening the connector screws.
wAvoid to place it near to heating sources, in dusty locations or smoky enviroments.
wTo avoid damage, the power supply has to be firmly fixed.
wTo avoid an electrical shock, neither remove the protection cover nor handle the connected wire in
the terminals.
wDo not use excessive force when tightening the connector screws.
wInstall the power supply in a dry and protected place without risk of drip or water projections.
wAvoid to place it near to heating sources, in dusty locations or smoky enviroments.
wDo not block ventilation holes of the equipments so that air can circulate freely.
ORemember, the installation and handling of these equipments must be performed by authorized
personnel and in the absence of electrical current.
Continue

SYSTEM CHARACTERISTICS
O.
l will be free.
Communication will last for one minute and a half or until the handset is hung up After the
communication, the monitor's status LED will iluminate (red) and the channe
OTo make a call, the visitor will have to push the door panel button: some acoustic tones will indicate
that the call has been done. In this moment, the monitor (phone) of the house receives the call.
OIn devices with several entry doors, the other door panel(s) will be automatically disconnected: if
another visitor needs to call, some phone tones will indicate that the is busy.channel
OThe call lasts for seconds; the master monitor shows the image after
receiving the call; while the visitor does not perceive it
If the call is not answered before seconds, the
l will be free
45 Tekna-S Plus 2 seconds
and master monitor's status LED will illuminate
(green) master monitor's status LED will illuminate
(red) and the channe
. 45
.
Oand the monitor's status LED will illuminate (green).To communicate, lift the handset from the monitor (phone)
Communication with hearing aid : The handset enables communication with hearing aids equipped with
T-mode, making conversation possible (inductive loop).
O
.
To open the door, press the door opener button during the call or communication: one touch
activates the door opener for three seconds
O.46 and 57Pages contain the description of the function buttons
VERY IMPORTANT NOTE
This device is delivered fully programmed, so that it can be used with its monitor; if
an additional monitor or phone is needed, it must be programmed (pages ,53-54
63 64and ).
If this device is part of a system with general door panels, the door panel and the
monitor must be programmed as shown on page .68
SYSTEM OPERATION
wDifferent call reception tones depending where the call is comming from: door panel, door bell
push button, intercom., porter's exchange.
wBrightness and co control.lor (Only monitor).
wInput for external door release push button.
wDoor release button.
w"Doctor mode" function (automatic door opening).
Description, installation, configuration and programming of the telephone (see manual T540 UNO SE
"Cód.50122 ") disponible en:257 https://doc.golmar.es/search/manual/50122257
Description, installation, configuration and programming of the monitor (see manual TTEKNA
PLUS "Code 5012 ") available in:
HF
2337 https://doc.golmar.es/search/manual/5012 .2337
OMonitor Tekna Plus:HF
OTelephone T540 Uno SE:
wMonitor status LED.
wTelephone status LED.
wProgramming LED.
Coming from previous page
43

1650
1850
1450
Positioning of the boxembedding
DOOR PANEL INSTALLATION
Installation of the boxembedding
44
Drill one hole in the wall so that the upper part of the is installed at a height of 1,65m.doorpanel
Drill dimensions are: 131(Width) x 131(Height) x 45(Depth) mm.
The has been designed to resist several environmental conditions. However, it is better to
take additional precautions to ensure a long life for it ( rain shields, covered places...). To obtain
image maximum quality in video door entry systems, avoid back lighting caused by light sources
(sun, lamps,...).
door panel
Break the partition wall to enter cables.
After the embedding box has been installed,
remove the protective stickers from the fixing
holes.
Pass the wiring through the hole made in the
bottom part of the embedding box. Fix the box
in the wall, adjust and level it.

DOOR PANEL INSTALLATION
Door panel configuration.
The is provided with microswitches and
a jumper in its rear part; Their functions are
described below.
(SW1)
(JP1)
door panel
When this switch is ON, the can (audio
and/or video communication without any call). In buildings with
several , just activate this function in one of them. In
systems equipped with a general this function can be
activated in one of each detached house.
door panel autoswitch-on
door panels
door panel,
door panel
Select monitors and telephones programming
Page describes monitors method; while
pages describes telephones method.
53-54 Tekna-S Plus program
63 T540 Plus SE program
ON for . Once the
programming progress is finished return the switch to OFF position.
Select in case of a main Each system must be
equipped with just one main all the others must be
OFF
(ON). In systems provided with a general
one of each house will be configured as main
door panel.
door panel; slave
door panels door panel,
door panel door panel.
Select if the is provided with a camera Select if it
has no camera.
OFF . ONdoor panel
Page describes the method68 program .
With a general select ON to program the backbone
installation.
door panel,
Once the programming progress is finished return the
switch to OFF position.
Equip the installation with a communication resistance. To ensure a
correct operation, this resistance must be activated only in the door
panel which is the nearest to the backbone installation or in the
general door panel (if one exists). If any RD-Plus/Uno SE repeater is
used, it must be deactivated in the door panels behind it.
*Factory value
123
123
It allows the connection of an alternative current
door opener; page shows the connection
diagram.
73
It allows the connection of a direct current door
opener; page shows the connection
diagram.
73
SW1
JP1
45

POWER SUPPLY INSTALLATION
Detail of installationFA-805 .power supply
To install the power supply in the wall, drill two holes whose diameter
6mm .is and insert the plugs Fix the power supply by means of
the proper screws.
The can be installed on a DIN 46277
guide rail (6 elements) pushing it slightly.
To remove the from the guide rail,
put a flat screwdriver under the edge and
prise it open as shown in the picture.
power supply
power supply
Install the power supply in a dry sheltered place.
Remember that, according to the regulations in force,
it is necessary to protect the power supply by means of
a magnetothermic switch.
LOCK RELEASE INSTALLATION
Detail of the lock release installation.
If the lock release must be installed on a metal door,
use a 3,5mm drill and thread the hole.
If it must be installed on a wooden door,
use a 3mm drill.
See connection diagrams on page .WARNING: 73
DIN 46277
46
The camera is equipped with an horizontal and vertical orientation device.
If orientation is not correct, change it.
If, when using the device, audio volume is inadequate, it is necessary to carry out
some adjustments, as shown in the picture.
Fix the to the box by means of the proper screws.doorpanel embedding
Final adjustments
DOOR PANEL INSTALLATION
3,5 x 45
DIN-7971
3,5 x 45
DIN-7971
M 4 x 8
3,5 x 25
DIN-7972
DIN-963

MONITOR DESCRIPTION 47
Descrip Tekna S Plus .tion of the - monitor
Descripción .of the connection terminals
Advanced programming LED.
LED blinking red rapidly.
- No volume (night mode):
LED blinking red.
- : LDoctor mode ED blinking green.
- Auto spy if Bus busy:
Connector fixings.
- In standby: LED illuminated red.
CN4 connector (end of line jumper).
JP1 ,jumper remove in video installation with twisted
pair (see EL562S module p.71-72" " ).
RJ-45 ).connector (installation with UTP cable
SW1 configuration switches.
CN2 connection terminals.
Monitor status LED (two-colour):
- : L .Call ED illuminated green (master monitor)
- Com unica : Ledm tion illuminated green.
CN .3 connection terminals
ak
b
c
q
m
n
p
d
o
j
i
h
g
JP1
1 2 3 4 5 6 7 8 9 10
CN2
CN3
SW1
l
k
e
f
75
TEKNA-S PLUS
11742126 V XX.
15090200000 SN ADDRESS
INTER A1 SLAVE MASTER
ATENCIóN
Alta tensión. No abrir la tapa.
Manipular sólo por personal
de v icio técnico.l ser
WARNING. GOLMAR S.A
High Voltage.Don´t open cover C/ Silici,13
Handle only by technicalservice 08940 - SPAIN
ESCALERA
STAIR
PISO
FLOOR
PUERTA
DOOR
CN4
Function/programming buttons.
Handset.
4.3" TFT colour screen.
Communication with hearing aids. SDet
the hearing aid switch to position T.
Cable slot.
Brightness control.
Colour control.
Cord.
c.
d.
b.
e.
a.
g.
h.
f.
p.
m.
n.
j.
i.
o.
k.
l.
q.
.
l.
Audio communicatio
Digital communication
Door bell button input.
Input for auxiliary door opening button.
Intercom .function
A :
D :
HZ- :
AP+:
INT :
CN3 :connection terminals Negativo (e e 18Vdc power supply)positiv .
Video signal input through coaxial cable.
Coaxial cable shield.
Video signal output through coaxial cable.
Balanced video signal (through twisted pair).
– :
Vin :
:
Vout :
, +
Vp, Mp :
CN2 :connection terminals
+
_Vin
_
A D HZ-
MP Vout
VP
+SA2C A1
_AP+INT
.Output for 2nd camera activation
Output (negative) for auxiliary device
activation (max. consumption 50mA).
Output (negative) for auxiliary call
( x. 250mA).repeater ma consumption
2C
A1 :
:
SA :
*
( )
*
( )
( )Shield

MONITOR DESCRIPTION
48
Function buttons.
(*) In advanced programming mode, the default functions of function buttons and can be changed with
one of the following functions at the same time and per button: 'intercom,' 'auxiliary device A1 activation,'
'second camera 2C activation' or 'call to secondary guard unit' (see p. ).56
One long press for 3 seconds during a call cancels the call on the monitor. If there are more
monitors in the apartment, they will continue with the ringtones of the door panel. During
communication with the door panel, the communication in progress will end.
One long press for 2 seconds: with the monitor in standby and the handset on the hook, this
activates ringtone volume mode, with a tone indicating the volume selected. Then each long 2-
second press (before 5 seconds elapse) selects a volume level: maximum, no volume 'night
mode,' minimum and medium, and so on (carousel mode). Note: The 'night mode' status LED
blinks red. During a call, the monitor does not emit a ringtone unless it is an 'apartment front
door call.'
One long press for 3 seconds: with the monitor in standby and the handset on or off the hook, this
turns the monitor off. Then one short 1-second press turns on the monitor. After any resetting of
the monitor and for the following 45 seconds, no operation with it can be performed.
With the monitor in standby and the handset off the hook, this activates the intercom function (in
the same apartment). One long press until a confirmation tone can be heard will call all of the
monitors in the apartment. To call individual devices, press the button once to call the 'master'
monitor, twice to call 'slave 1,' 3 times to call 'slave 2,' 4 times to call 'slave 3' and 5 times to call
'slave 4.' This selective intercom call mode is only available with Tekna Plus SE, Tekna Plus and
Tekna Plus monitors. This only functions if no call or communication is in progress.
-S
HF
With the monitor in standby and the handset on the hook, this enables the image from the door
panel configured as main to be viewed (if the bus is busy, the status LED of the monitor will
indicate so with a few quick blinks). With the handset off the hook, this enables audio and video
communication with door panels that have their auto switch-on function activated to be
established. This only functions if no communication is in progress.
Regardless of the position of the handset, this activates auxiliary device 'A1.'
In call, a slave monitor enables the image of the door panel to be captured.
With the monitor in standby and the handset on the hook, this makes a panic call to the guard
units configured to receive such calls. With the handset off the hook, it enables a normal call to
be made to the main guard unit. During call reception and communication processes, it
enables the lock release to be activated.
( )
*
( )
*
The handset of the Tekna-S monitor enables communication with hearing aids equipped with T-mode,
making conversation possible (inductive loop). Set the hearing aid switch to position T.
Plus
Remember:
.
T

MONITOR DESCRIPTION 49
Description of the SW1 DIP switch (quick programming mode).
The SW1 DIP switch is located on the right-hand side of the back
of the monitor.
It enables the monitor to be configured as master / slave and an address
to be assigned.
*Factory default
Description of the RJ-45 connector (installation with UTP cable).
It enables connection of the system's main communication wires
(+, -, A, D, Vp y Mp) in twisted-pair installations.
The monitor features an RJ-45 connector for installation with a UTP
cable. It is located on the right-hand side of the back of the monitor.
The monitor code is the sum of the values of the switches set to ON.
Dip3 to Dip10: To set the monitor address.
This kit video SV-801 S, . The
switches set to OFF have a zero value..
must be set the monitor only with address "106"
The values of the switches set to ON are shown in the table below.
Remind: Up to two monitors and one phone in each house without extra
power supply.
Dip1 Dip2: Dip1 Dip2
OFF , Dip1 ON Dip2 OFF s 1, Dip1 OFF Dip2
and To set the the monitor as master / slave. and to
master to and to lave to and
to lave and to laveON s 2, Dip1 Dip2 ON s 3.
Example: 0+64+32+0+8+0+2+0=106
Switch number:
Value when ON:
4
64
5
32
6
16
7
8
8
4
9
2
10
1
3
128
RJ-45 connector (Cable type: T568B)
Male connector Female connector
PAIR 2 PAIR 1 PAIR 4
PAIR 3
12345678
12345678
Pin Ethernet cable Golmar connection
1White + Orange
2
3
4
5
6
7
8
GND (Audio)
Audio
Orange
GND (Data)
White + Green
+18V
Blue
+18V
White + Blue
Data
Green
Vp
White + Brown
Mp
Brown
RJ-45 equivalence table
Important: This type of programming cannot be performed on a general door panel.
NOT :E For this type of installation, contact our Golmar technical support department.
SW1
1 2 3 4 5 6 7 8 9 10
CN2
CN3
SW1
8 9 10
CN2
CN3

MONITOR ADJUSTMENTS
50
Use of the jumperend of line .
The end of line jumper is located in CN4 connector, in the rear part of the
monitor In systems with twisted pair, the end of line jumper is located in the
EL562 module (see next paragraph)
.
S
Do not remove jumper in those monitors where the video cable end is
located.
Remove jumper only in intermediate monitors.
EL562 .S module for video installations with twisted pair
Find connectorCN4 .at the back of the monitor on the right-hand side
To insert the S first the jumper located in the CN4
connector and JP1 of the monitor.
EL562 module, remove
See the specific installation diagram.
NOT :E (coaxialThe door panel admits both installation types or twisted pair
installation without making any change) .
75W
CN4
JP1
75W

MONITOR INSTALLATION 51
Positioning the wall mounting connector.
Avoid dusty or smoky environments or locations near sources of heat.
The top of the connector must be positioned at a height of 1.60 m. The minimum distance between the
sides of the connector and the closest object must be 5 cm.
1.60m
Fix the monitor's wall mounting connector to the wall by drilling two 6mm diameter holes and using the
screws and plugs supplied with the terminal.
2 3
Connect the cables to the monitor (see p. 4 ), position the monitor in front of the wall mounting
connector, ensuring that the holes in the base of the monitor line up with those on the connector ,
and then move the monitor downwards until the monitor is securely fixed to the connector .
7
Remember: R
1
23
x4 30
1
Fixing the monitor´s wall mounting connector to the wall.
Positioning the monitor.

MONITOR INSTALLATION
52
Location of the embedding box.
Make a hole in the wall to position the top of the universal embedding box at a height of 1.60 m from
the ground. The minimum distance between the sides of the embedding box and the closest object
must be 5 cm. Avoid dusty or smoky environments or locations near sources of heat.
Pass the cable through the hole made in the embedding box. Embed the box and ensure that it is level
and flush. Fix the wall mounting connector of the monitor to the embedding box with the screws
supplied.
Positioning the embedding box and fitting the wall mounting connector.
1.60m
Screws supplied with
the embedding box.
2 3
Remember: R
Connect the cables to the monitor (see p. 4 ), position the monitor in front of the wall mounting
connector, ensuring that the holes in the base of the monitor line up with those on the connector ,
and then move the monitor downwards until the monitor is securely fixed to the connector .
7
1
23
1
Positioning the monitor.

Programming the Tekna Plus monitors-S .
RE :MEMBER Monitors must be programmed only in case of installed
parallel units or if there are general door panels.
Find the configuration switch located in the rear part of the door panel and set
number to The will produce a tone, indicating that it has
entered mode. In systems with more than one this
operation must be carried out only in the main of each building.
2 ON. door panel
program door panel,
door panel
Important: To perform this programming, the monitor's SW DIP switches be set
to .
1
OFF
MONITOR PROGRAMMING 53
Continue
Turn off the monitor to be programmed (press button for 3
seconds). Once switched off, press door release button .
Press and hold door release button and, without releasing it,
switch on the monitor (press button for 1 second).
To show that the device is ready for programming, the
door panel and monitor will emit a number of tones
(the status LED on the monitor will illuminate red),
enabling door release button to be released. To
establish audio communication with the door
panel, lift the handset.
Press the door panel button that will call this monitor.
At this moment, the door panel and monitor will
emit a number of tones (the status LED on the
monitor will blink red).
S
SI
To programme the monitor as , press button for 3 seconds (the
monitor's LED will illuminate red).
Master
To programme it as , press button once and the status
LED will blink (green) once. Continue successively to ,
pressing button four times and the status LED will blink (green)
four times.
Slave 1
Remind: Up to two monitors and one phone in each house without extra
power supply.
To programme it as , press button and the LED
will blink (green) once.
Slave + Intercom
M

MONITOR PROGRAMMING
54
Each apartment must have one master unit only; in case of parallel units configure them as slaves,
both monitors or telephones.
Once the programming has been finished, set to OFF the programming
switch. If you don't, the door panel will reproduce a tone to advise that the
system is still into programming mode.
Make a call to check that the monitor has been succesfully programmed.
Repeat these steps to program the rest of monitors.
D1escription of the SW DIP switch (quick programming mode).
The SW DIP switch is located on the left-hand side of the back of the
monitor.
It enables the monitor to be configured as master / slave and an address
1
to be assigned.
*Factory default
Dip3 to Dip10: To set the monitor address.
The monitor code is the sum of the values of the switches set to ON.
The values of the switches set to ON are shown in the table below.
This kit video SV-801 S, . The
switches set to OFF have a zero value..
must be set the monitor only with address "106"
Dip1 Dip2: Dip1 Dip2
OFF , Dip1 ON Dip2 OFF s 1, Dip1 OFF Dip2
ON s 2, Dip1 Dip2 ON s 3.
and To set the the monitor as master / slave. and to
master to and to lave to and
to lave and to lave
Remind: Up to two monitors and one phone in each house without extra
power supply.
Example: 0+64+32+0+8+0+2+0=106
Switch number:
Value when ON:
4
64
5
32
6
16
7
8
8
4
9
2
10
1
3
128
Important: This type of programming cannot be performed on a general
door panel.
Coming from previous page
To programme it as (in call), press button and
the status LED will blink (green) once. If button is pressed again, the
monitor will return to being programmed as (in call)
and the status LED will blink (green) twice. The door panel video will be
displayed during a call if programmed to do so:
Slave without video
Slave with video
SV
To exit, press button (the monitor's LED will illuminate red).
SW1
1 2 3 4 5 6 7 8 9 10
CN2
CN3

55
MONITOR PROGRAMMING
Advanced programming of monitorTekna-S Plus .
Advanced programming enables the monitor's default settings to be changed:
Continue
To activate doctor mode: Press button and the programming LED will indicate with
2 blinks that the function is activated (the status LED will blink green) or with 1 blink
that the function is deactivated.
Turn off the monitor to be programmed (press button for 3 seconds).
Once switched off, press button to access of advanced
programming and the programming LED will illuminate.
'Menu 1'
Then adjust the settings as required:
- Acti / de :vating activating the doctor mode function ( ).Doctor mode not activated default setting
Select the ringtone to be changed: Each press on button selects a ringtone which
is indicated with blinks (1 to 4 blinks) of the programming LED and in the following
order: door panel, guard unit, intercom call and 'HZ' apartment front door call.
When the final selection is reached, the following press returns the user to the first
selection and 1 blink of the programming LED (carousel mode).
- Changing the ringtone melody:
Then select the melody for the ringtone (selected in the previous step) by pressing button
...... til the required 'carousel mode' melody is heard.
The monitor has different ringtones to identify the origin of the call. The melodies assigned by default to
the ringtones can be selected from among others available on the monitor.
The doctor mode function enables the lock release to be activated automatically conds after
making a call from the door panel without having to establish communication or press door release
button....... The call ends after 20 seconds and the channel will become free.
" " 6 se
.
( " ").Only the master monitor should be configured with doctor mode
Men 1:u
- Acce "Men 2" :ssing u or exiting programming mode
To access press button and the programming LED will blink twice.'Menu 2'
To exit programming mode, press button for 3 seconds, and the programming
LED will turn off (see p. ).58
No function.
- .Button has not function

56 MONITOR PROGRAMMING
Continue
Coming from previous page
No function.
Men 2:u
Then adjust the settings as required:
- .Button has no function
- :Changing the function of button Intercom function default function( ).
Select the function to assign to button : Each press on button selects a different
function which is indicated with blinks (1 to 4 blinks) of the programming LED and in the
following order: auxiliary device 'A1' activation, call to secondary guard unit, second
camera '2C' activation and intercom. When the final selection is reached, the following
press returns the user to the first selection and 1 blink of the programming LED (carousel
mode).
- :Changing the function of button "A1" ( ).Activation of auxiliary device default setting
Select the function to assign to button : Each press on button selects a different
function which is indicated with blinks (1 to 4 blinks) of the programming LED and in
the following order: auxiliary device 'A1' activation, call to secondary guard unit,
second camera '2C' activation and intercom. When the final selection is reached, the
following press returns the user to the first selection and 1 blink of the programming
LED (carousel mode).
If an apartment has Tekna Plus Tekna S Plus monitors, the
Tekna S Plus monitors should be configured with 'Intercom with Tekna
Plus monitors' mode, as Tekna Plus monitors do not allow an intercom call
to a particular monitor in the apartment to be made (selective intercom call). So when an intercom
call is made, all of the monitors in the apartment will receive the call.
, T540 Plus and T540 Plus SE telephones,
and T540 Plus SE telephones
and T540 PLus telephones
- Intercom monitors/telephones:with Plus Intercom Tekna /T540 Plus SE ( ).with -S Plus default setting
To activate the Intercom with Tekna Plus monitors mode: Press button , and the
programming LED will indicate with 1 blink that the function is in 'Intercom with
Tekna Plus monitors' mode or with 2 blinks that the function is in 'Intercom with
Tekna S Plus monitors' mode.
- Acce "Men 3" o :sing u r exiting programming mode
To access press button and the programming LED will blink three times.'Menu 3'
To exit programming mode, press button for 3 seconds, and the programming
LED will turn off (see p. ).58

57
Coming from previous page
MONITOR PROGRAMMING
Continue
Men 3:u
Then adjust the settings as required:
- Rep :eating the ringtones One repeat (default setting).
To 'repeat the ringtone' on the monitor: Each press on button selects a repeat of
the ringtones which is indicated with blinks (1 to 3 blinks) of the programming LED
and in the following order: 1, 2 or 3 repeats. When the final selection is reached,
the following press returns the user to the first selection and 1 blink of the
programming LED (carousel mode).
- " ":Setting the door panel communication time
Activating the in-call video: Press button and the programming LED will indicate
with 2 blinks that the video will appear on the monitor when a call is received or with
1 blink that the video will appear at the end of the ringtone.
- :Activating the in-call video The video appears when a call is received default setting( ).
No function with kit videoSV-801 S .
- " " :Setting the door panel call time
- Acce "Men 4" o :sing u r exiting programming mode
To exit programming mode, press button for 3 seconds, and the programming
LED will turn off (see p. ).58
To access press button , and the programming LED will blink 4 times.'Menu 4'
No function with kit videoSV-801 S .

58
Coming from previous page
MONITOR PROGRAMMING
Men 4:u
Then adjust the settings as required:
- Setting to the default setting" ", all the monitor's advanced programming options
Sin función.
- .Button has no function
Sin función.
- .Button has no function
Sin función.
- .Button has no function
- :
Accessing 'Menu 1' or exiting programming mode
To access press button , and the programming LED will blink once (see
p ).
'Menu 1'
age 55
To exit programming mode, press button for 3 seconds and the programming LED
will turn off.
When exiting advanced programming mode, the monitor will turn off: Press button
..... or 1 second to turn on the monitor (the monitor's LED will illuminate red). After
any resetting of the monitor and for the following 45 seconds, no operation with it
can be performed.
-Turning on the monitor when exiting programming:
Setting to the 'default setting': Press button and the monitor will indicate with two
audible tones that all of the options of the monitor's advanced programming (pp.
55 8-5 ) are set to their default setting.

Descrip T- 40 Plustion of telephone.5 SE
TELEPHONE DESCRIPTION 59
Description of the connection terminals.
a
d
c
e
b
h
e
f
a. Telephone handset.
b. .Speaker grille
g. Telephone status LED:
c. Microphone hole.
-
-
-
-
-
Standby: LED illuminated red.
Call: LED illuminated green (master
telephone).
Communication: LED illuminated green.
Night mode: LED blinking red.
Doctor mode: LED blinking green.
e. Telephone cord connectors.
d. Subjection hole.
f. Function / programming buttons.
h. Hook switch.
g
AP+ SA
_A D Int A1 _HZ +
+-
Positive, negative (18Vdc power supply).
Audio, digital communication.
Auxiliary door release button input.
Door bell button input.
Output (negative) auxiliary call repeater (max. consumption 250mA).
Intercom function.
Output (negative) auxiliary device activation (max. consumption 50mA)
+, - :
.
A , D :
A :P+
HZ :-
SA :
INT :
A :1