golmar Jazz GB2 User manual

USER MANUAL
Code 50122156 T ENJAZZ VESTA2-VESTA7 REV.0 13 7
Jazz GB2 Video Door
Entry System Kit
2-wire installation
TECHNOLOGY

JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
INTRODUCTION
First of all, we thank and congratulate you for purchasing this product.
Our commitment to achieving the satisfaction of customers like you is manifested through our ISO-9001 certification
and the manufacture of products like the one you have just purchased.
Its advanced technology and strict quality control will ensure that customers and users enjoy the numerous features
that this device offers. To get the most out of them and ensure proper operation from day one, we recommend that you
read this instruction manual.
CONTENTS
2
SET-UP WARNINGS
-Do not overtighten the screws on the power supply connector.
-Always disconnect the power supply before installing or making modifications to the devices.
-The fitting and handling of these devices must be carried out by .authorised personnel
-The wiring must run at least .40cm away from any other wiring
-Before connecting the device to the mains, check the connections between the door panel, power supply unit,
distributors, camera interface, GSM interface (VESTA2 monitor only) and monitors.
-Use the Golmar cable (2x1mm ).RAP-2150 2
-Always follow the instructions contained in this manual.
Introduction....................................................................................................................................................................2
Contents........................................................................................................................................................................2
Set-up warnings............................................................................................... ................................. 2............................ .
Safety precautions.......................................................................................... ...................................................3............
Characteristics.............................................................................................................................................................. 3.
System operation.................................................................................................... ....................................... 3............... .
Description of JAZZ surface panel....................................................................................... .......................................4....
Exploded view of the parts of the JAZZ panel.......................................................................................... .......................5. .
Door panel.......................................................................................................................................................................
............................................................................................................................................5
Location of the door panel
............................................................................................................................................6Removing the metal front
.......................................................................................................................................... 6.Positioning the door panel
.................................................................................................................................................. 6Wiring the door panel
............................................................ ........................... 7...................... .Codes assigned to the door panel call buttons
.............................................................................. .......................... 7...............................Description of the DIP switch
........................................................................ ............................................ ..8. .Description of the configuration jumper
....................... ......................................................8...............Description of the illumination LEDs (low light conditions)
...................................................... ...............................................8..Description of the visual signals on the door panel
............................................................................................................8.Setting the door panel communication volume
.................................................................................. ...................9............................Setting ringtone operating mode
...................................................... ......................................9...Setting door panel mode with or without shield installed
.............................. .................. 9..........Setting contact mode for CV-/CV+ (lock release) and C1/NA1 (auxiliary device)
.................................. ........10....... .Setting the activation time for CV-/CV+ (lock release) and C1/NA1 (auxiliary device)
........................................................................ ............10....................Setting card reader illumination operating mode
................................................................. ............10.....................Setting door panel illumination LED operating mode
.................................................................................................................... .............11.Setting the door panel address
...................................................................................................................... ................ 11. .Positioning the card reader
.................................................... ......................................... 11.................... .Positioning the button identification labels
............................................................................................. ...............................................12...Closing the door panel
Installing the power supply unit (FA-GB2/A) and lock release....................................................................................... 13.
Wiring diagrams with the VENTA2 monitor.................................................................................. .................. 14-19......... .
Wiring diagrams with the VESTA7 monitor................................................................................... ................. 20-25......... .
Connection diagrams for up to 4 access panels............................................................................ ....................... ...26..... .
Connection diagrams withAC lock release, 2nd AC lock release or automatic gate..................... ........ 27......................... .

CHARACTERISTICS
-Video door entry system with simplified wiring (non-polarised 2-wire bus).
-Up to 4 access panels (DP-GB2Adistributor required for more than one access panel) per installation.
-Up to 2 apartments per installation.
-Maximum 6 Vesta2 monitors or 4 Vesta7 monitors per installation.
-Maximum 4 monitors in parallel (without distributors) per installation.
-In installations with 1 apartment, maximum 6 Vesta2 monitors or 4 Vesta7 monitors.
-In installations with 2 apartments, maximum 6 Vesta2 monitors or 4 Vesta7 monitors.
-Combinations with Vesta2 monitors:
w1monitor in one apartment and 5 monitors in the other apartment.
w3monitors in each apartment.
-Combinations with Vesta7 monitors:
w1monitor in one apartment and 3 monitors in the other apartment.
w2monitors in each apartment.
-Visual signals on the door panel for people with impaired hearing (indicating call process, communication, door open
and channel busy).
-Door opening and auxiliary device activated for 5 seconds (configurable).
-DC lock release.
-Potential-free contact for activation of auxiliary devices (2nd AC lock release, gate, etc.); do not exceed values of
12Vdc/1Abetween terminals 'C1' and 'NA1' on the door panel.
-Input for exterior door opening button (output 'CV-' and 'CV+').
-Confirmation tone when the call button is pressed.
-DIP switches to configure door panel address, call mode, door panel with/without shield, type of contact/time for lock
release and auxiliary device output, card reader illumination mode and LED function mode (low light conditions).
-Maximum distance between the power supply and the furthest door panel: 65m with a cross-section of 1mm .
2
-Maximum distance between the power supply and the last distributor: 60m with a cross-section of 1mm .
2
-Maximum distance between distributor and monitor: 30m with a cross-section of 1mm .
2
SYSTEM OPERATION
3
SAFETY PRECAUTIONS
-Always disconnect the power supply before installing or making modifications to the devices.
-The fitting and handling of these devices must be carried out by .authorised personnel
-The wiring must run at least 40 cm away from any other wiring.
-On the power supply unit:
wDo not overtighten the screws on the connector.
wInstall the power supply unit in a dry protected location free from the risk of dripping or splashing water.
wAvoid locations that are humid, dusty or near heat sources.
wEnsure that the air vents are free from obstruction so that air can circulate freely.
wTo avoid damage, the power supply unit must be firmly secured in place.
wTo prevent electric shock, do not remove the cover or handle the wires connected to the terminals.
-To make a call, the visitor must press the button of the apartment; an audible sound indicates that the call is being
made and LED will turn on.At this moment, the apartment's monitors receive the call. If another apartment is called
by mistake, press the button for the correct apartment and the first call will be cancelled.
-In systems with several access doors, the other door panel(s) will be automatically disconnected. If another visitor
tries to call, a number of telephone tones will be heard to indicate that the system is busy and LED will illuminate.
-The call lasts for 40 seconds. The image appears on the monitor (with code 0 'apartment 1' or code 16 if the call is in
'apartment 2') when receiving the call without the visitor knowing.
If the call is not answered within 40 seconds, LED will turn off and the channel will be freed.
-To establish communication, press button on any monitor in the apartment. Door panel LED will turn on.
If the monitor is a VESTA2 GB2/H or VESTA7 GB2/H with icon on the front, make sure that the hearing aid is
between 15 and 25 cm away from the monitor to ensure maximum audio quality during communication with the
door panel.
-Communication will last for one and a half minutes or until button is pressed again. When communication has
finished, LEDs and will turn off and the channel will be freed.
-To open the door, press button during the call or communication processes: one press will activate the lock release
for five seconds and LED will also turn on for five seconds.
-To activate the auxiliary device output, press button on the Vesta7 monitor or via the Vesta2 monitor's lock release
menu 2 (for lock release 2, it is necessary to enable lock release function 2 on the Vesta2 monitor) during call or
communication processes: a single press activates the auxiliary device output for five seconds, LED will also
illuminate for five seconds.
-For a description of the functioning and setup of the monitor, see the monitor's user manual.
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

DESCRIPTION OF THE JAZZ SURFACE PANEL
4
Input for exterior door opening button (CV-, CV+).
:Contact 'C' for auxiliary device (2nd AC lock release, gate, etc.).
:Contact 'N.O.' for auxiliary device (2nd AC lock release, gate, etc.).
:12Vdc output for Golmar DC electric lock.
:Communication BUS (non-polarised).
:Communication BUS (non-polarised).
AP +,AP :
C1
NA1
CV ,CV+
BUS
BUS
Note: See wiring diagrams for connections (pp. 14-27).
_
Description of the JAZZ surface panel:
ON
1 2 3
AP- C1 NA1 AP+ CV- BUSBUS
CV+
n
k
m
h
a
b
c
d
e
f
i
jk
b
c
d
e
f
gp
o
h
i
l
_
a. Shield.
b. Colour television camera.
c. Microphone.
d. LEDs (activation with ambient light).
e. Speaker.
f. LEDs (visual signals for people with
impaired hearing).
g. Card reader.
h. Call button apartment 2.
(2-button door panel models only).
i. Call button apartment 1.
j. Metal front fixing screw (x1).
k. Holes for fixing to wall (x4).
l. Do not use (internal use).
m.Connection terminals.
n. Wiring entry.
o. DIP switch.
p. No function.
Connection terminals:
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

5
Exploded view of the parts of the panel.
Aluminium frontElectronic moduleShield
Description of the door panel:
INSTALLATION OF THE DOOR PANEL
Locate the top of the door panel at a height of 1.65m.
The door panel has been designed to withstand diverse environmental conditions. It is however advisable to take
extra precautions to prolong its service life, such as using the shield supplied or locating it in a covered area.
For optimum image quality, avoid direct contact from light sources (sunshine, street lights, etc.).
Location of the door panel:
DESCRIPTION OF THE JAZZ SURFACE PANEL
-JAZZ J5110/VESTA2 1P KIT (Code 11500241).
-JAZZ J5110/VESTA7 1P KIT (Code 11500242).
-JAZZ/1 SURFACE DOOR PANEL (Code 11525401).
-JAZZ/2 SURFACE DOOR PANEL (Code 11525402).
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
1650
1850
1450

6
Removing the metal front:
INSTALLATION OF THE DOOR PANEL
Remove the screw at the bottom of the door panel
using the Allen key supplied with the product.
Wiring the door panel:
AP- C1 NA1 AP+ CV- BUSBUS
CV+
Remove the metal front as shown in the drawing.
Positioning the door panel:
Present the shield and the electronic module to the wall, placing
the top of the module at a height of 1.65m from the ground, and
pass the wiring through the cable entry.
Make 4 x 6mm diameter holes, two located at the top of the
module and the other two at the bottom, and fix the shield and
electronic module to the wall using the plugs and screws supplied.
Important: The distance between the top of the electronic module
and the shield should be 7mm, so that the metal front can be
correctly positioned when closing the door panel.
To access the connection
terminals, remove the card
reader.
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
Then connect the wiring to the
connector strip of the electronic
module, following the instructions
in the wiring diagrams.

7
INSTALLATION OF THE DOOR PANEL
Codes assigned to the door panel call buttons:
Button 'P2': Codes 16-21.
(Apartment 2) 2-button door panels only.
Button 'P1': Codes 0-5.
(Apartment 1).
The sound module's P1 and P2 buttons are assigned with factory codes.
-Apartment 1, button 'P1': Enables codes 0-5 to be assigned to the monitor.
Monitors in this apartment must be set with codes in order of allocation from 0 to 5.
When button 'P1' on the door panel is pressed, all of the monitors in apartment 1 will receive the call and only
the monitor assigned with code 0 will show the door panel image. If the call is answered from any other
monitor in the apartment, the image on the monitor assigned with code 0 will disappear and audio and video
communication will be established with the door panel.
-Apartment 2, button 'P2': Enables codes 16-21 to be assigned (2-button door panel only).
Monitors in this apartment must be set with codes in order of allocation from 16 to 21.
When button 'P2' on the door panel is pressed, all of the monitors in apartment 2 will receive the call and only
the monitor assigned with code 16 will show the door panel image. If the call is answered from any other
monitor in the apartment, the image on the monitor assigned with code 0 will disappear and audio and video
communication will be established with the door panel.
Description of the configuration DIP switch:
ON
1 2 3
The DIP switch is located on the right side of the circuit, accessible by opening the
door panel.
1 2 3
ON
Door panel address: (DIP 3 always OFF).
DIP switches: 1 and 2 OFF (address 1), 1 ON and 2 OFF (address 2), 1 OFF and 2
ON (address 3), 1 and 2 ON (address 4).
With DIP 1 and DIP 2 OFF (DIP 3 always ON), the following can be configured: See pp. 9-10.
-With button 'P1', ringtone operating mode during a call process.
-With button 'P2', whether the door panel is installed with or without shield.
*
( )
*
( ) Factory setting.
*
( )
ON
1 2 3
AP- C1 NA1 AP+ CV- BUSBUS
CV+
1. To select the address of the door panel (DIP 3 must always be OFF):
2. To configure the door panel (DIP 3 must always be ON):
1 2 3
ON
With DIP 1 ON and DIP 2 OFF (DIP 3 always ON), the following can be configured: See pp. 9-10.
-With button 'P1', lock release output 'CV-' and 'CV+', whether N.O. (factory setting) or N.C.
-With button 'P2', activation time of lock release and auxiliary device outputs.
1 2 3
ON
With DIP 1 OFF and DIP 2 ON (DIP 3 always ON), the following can be configured: See pp. 9-10.
-With button 'P1', operating mode of card reader illumination.
-With button 'P2', operating mode of door panel illumination LEDs with low light.
1 2 3
ON
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

8
INSTALLATION OF THE DOOR PANEL
Description of the configuration jumper:
BUS
Important: Do not change the configuration jumper's factory position.
Description of the door panel illumination LEDs (for low light conditions):
The door panel lighting LEDs will turn on during a call if the door panel lighting at
that moment is low. This enables the user to view the person who has called
from the apartment monitor.
*
( )
*
( ) Factory setting.
Description of the visual signals on the door panel:
Visual signals on the door panel for people with impaired hearing, indicating:
-In call: LED ' ' will illuminate during in call and in communication times.
-In communication: LED ' ' will illuminate during the communication process.
-When the door is open: LED ' ' will illuminate when the door is open.
-When ending communication: LEDs ' ' and ' ' will turn off.
-With more than one door panel, when calling and one is already in communication: LED ' ' will illuminate for
10 seconds.
-In call and the monitor is in 'Do not disturb' mode: No LED will illuminate, the door panel will emit a quick tone.
-In call (apartment without monitor or telephone): No LED will illuminate, the door panel will emit 3 quick tones.
Note: Communication in auto switch-on mode does not occupy the channel and the door panel communication
LED does not illuminate.
Setting the door panel communication volume:
If the audio volume of the door panel is too low after turning it on, follow these steps:
-Call the apartment.
-When the call is received in the apartment, establish communication by pressing button on the monitor.
-Then press the button used to call the apartment for 3 seconds until a number of confirmation tones are heard
and door panel communication LED starts to blink.
-Each press on the call button will increase the door panel volume and blink speed of the LED.
.
There are 5 volume settings and the blink speed of LED will increase for each. Slow to fast blink - low to
high volume.After reaching setting 5, maximum blink speed and volume, the next setting is 1, minimum blink
speed and volume (carousel mode).
-To save the volume setting, keep the button pressed until a number of confirmation tones are heard and the
door panel communication LED turns on.
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
*
*

9
INSTALLATION OF THE DOOR PANEL
Setting ringtone operating mode:
To configure the door panel ringtone when making a call, follow these steps: See p. 7.
-In the configuration DIP switch, set DIP 1 and DIP 2 to OFF and DIP 3 to ON.
-The card reader illumination will blink slowly.
-Then with the P1 call button, each press selects a different option and in carousel mode:
If pressed once: Configure the door panel with one ringtone.
LED illuminates and the door panel emits a long tone.
If pressed twice: Configure the door panel to hear tones during the call process.
LED illuminates and the door panel emits two long tones.
If pressed three times: Configure the door panel without a ringtone (factory setting).
LEDs and illuminate and the door panel emits three long tones.
-Once the required option is selected, stop pressing P1. Then set DIP 3 to OFF and the door panel
will exit configuration, saving the selected option. Remember to configure the address of the door panel.Note:
P1
Setting door panel mode with or without shield installed:
To configure the door panel with or without shield installed, follow these steps: See p. 7.
-In the configuration DIP switch, set DIP 1 and DIP 2 to OFF and DIP 3 to ON.
-The card reader illumination will blink slowly.
-Then with the P2 call button, each press selects a different option and in carousel mode:
If pressed once: Configure the door panel with shield installed (factory setting).
LED illuminates and the door panel emits a long tone.
If pressed twice: Configure the door panel without shield installed.
LED illuminates and the door panel emits two long tones.
-Once the required option is selected, stop pressing P2. Then set DIP 3 to OFF and the door
panel will exit configuration, saving the selected option.
Note: Remember to configure the address of the door panel.
P2
Setting contact mode for CV- and CV+ (lock release) and C1 and NA1 (auxiliary device):
To change the contact mode for lock release and auxiliary device activation, follow these steps: See p. 7.
-In the configuration DIP switch, set DIP 1 to ON, DIP 2 to OFF and DIP 3 to ON.
-The card reader illumination will blink slowly.
-Then with the P1 call button, each press selects a different option and in carousel mode:
If pressed once: Configure the door panel with contact mode N.A. (factory setting).
LED illuminates and the door panel emits a long tone.
If pressed twice: Configure the door panel with contact mode N.C.
LED illuminates and the door panel emits two long tones.
-Once the desired option is selected, set DIP 3 to OFF and the door panel will exit configuration,
saving the selected option.
Note: Remember to configure the address of the door panel.
Important: The type of contact selected will be for both the lock release and the auxiliary device.
P1
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

10
INSTALLATION OF THE DOOR PANEL
Setting the activation time for CV- and CV+ (lock release) and C1 and NA1 (auxiliary device):
To change the activation time for the lock release and auxiliary device, follow these steps: See p. 7.
-In the configuration DIP switch, set DIP 1 to ON, DIP 2 to OFF and DIP 3 to ON.
-The card reader illumination will blink slowly.
-Then press and hold down call button P2; LED will blink indicating with each blink 1 second and also a tone will
indicate every time it is heard 1 second for the activation time.
-Once the desired activation time is configured, set DIP 3 to OFF and the door panel will exit
configuration, saving the setting.
Note: Remember to configure the address of the door panel.
Important: The time configured will be for both the lock release and the auxiliary device.
P2
Setting card reader illumination operating mode:
To configure the card reader illumination operating mode, follow these steps: See p. 7.
-In the configuration DIP switch, set DIP 1 to OFF, DIP 2 to ON and DIP 3 to ON.
-The card reader illumination will blink slowly.
-Then with the P1 call button, each press selects a different option and in carousel mode:
If pressed once: Card reader always illuminated (factory setting).
LED illuminates and the door panel emits a long tone.
If pressed twice: Card reader always off.
LED illuminates and the door panel emits two long tones.
If pressed three times: The card reader automatically turns on or off depending
on the ambient light (day/night mode).
LEDs and illuminate and the door panel emits three long tones.
-Once the required option is selected, stop pressing P1. Then set DIP 3 to OFF and the door panel will exit
configuration, saving the selected option. Remember to configure the address of the door panel.Note:
P1
Setting door panel illumination LED operating mode:
To configure the door panel illumination LED operating mode, follow these steps: See p. 7.
-In the configuration DIP switch, set DIP 1 to OFF, DIP 2 to ON and DIP 3 to ON.
-The card reader illumination will blink slowly.
-Then with the P2 call button, each press selects a different option and in carousel mode:
If pressed once: Illumination LEDs always activate when a call is made from the door panel.
LED illuminates and the door panel emits a long tone.
If pressed twice: Illumination LEDs always off.
LED illuminates and the door panel emits two long tones.
If pressed three times: Illumination LEDs activate when a call is made and door panel
illumination at that moment is low (factory setting).
LEDs and illuminate and the door panel emits three long tones.
-Once the required option is selected, stop pressing P2. Then set DIP 3 to OFF and the door panel
will exit configuration, saving the selected option. Remember to configure the address of the door panel.Note:
P2
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

Positioning the card reader:
Positioning the button identification labels:
After completing the wiring and configuration work, position the
card reader in the electronic module. Fix using the screws
supplied.
Important: Before closing the card reader, make a test call to
the apartment(s) to ensure that it works correctly.
ON
1 2 3
The DIP switch is located on the right side of the circuit, accessible by opening the
door panel.
1 2 3
ON
Door panel address: (DIP 3 always OFF).
DIP switches: 1 and 2 OFF (address 1), 1 ON and 2 OFF (address 2), 1 OFF and 2
ON (address 3), 1 and 2 ON (address 4).
*
( )
*
( )
Important: To select the address of the door panel (DIP 3 must always be OFF).
11
INSTALLATION OF THE DOOR PANEL
Setting the door panel address:
Configure door panel addresses as described below:
Important: Position the card reader at the top with the black band visible.
A B C
Open the label cover (figure A ), insert the label (figure B ) and close (figure C ).
Customise and download the 'JAZZ LABELLER KIT REV.0117' label from Golmar's documentation website:
https://doc.golmar.es/search/manual/50180198
Open the label cover
*
( )
*
( )
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

12
INSTALLATION OF THE DOOR PANEL
Closing the door panel:
Fix the metal front with the screw using the Allen key
supplied with the product, as shown in the drawing.
Once the work is complete, make a test call to the
apartment(s) to check it works correctly.
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
*Protective cover
To finish the mounting of the door panel, replace the
metal front.
Remember: Insert the protective c ofsilicone over
the configuration witch.DIP s
Important: only 1 call push buttonDoor panels with ,
must cover the hole of the unused button withpush
the circular adhesive supplied with the kit.
Adhesive to cover hole of the push button
not used. (Only 1door panels with call
push button).
*
Door panelwith
1 Push button
**
**

13
INSTALLATION OF THE POWER SUPPLY UNIT
Installing the FA-GB2/A power supply unit:
Replace the protective cover once the input terminals have been wired.
Please note that current regulations stipulate that the power
supply must be protected by a circuit breaker.
Connect the FA-GB2/A power supply unit to the earth
connection.
Mount the DIN rail to the wall with the plugs and screws
supplied.
Then attach the power supply by applying slight
pressure.
The power supply can be installed on a DIN 46277 rail.
.
To remove the power supply unit from the DIN rail, use a flat
screwdriver to lever it off, as shown in the drawing.
The FA-GB2/A model requires 8 elements on the rail.
IMPORTANT: the maximum number of units that can be connected to an FA-GB2/A power supply is 6 VESTA2
monitors or 4 VESTA7 GB2 monitors.
Install the power supply unit in a dry protected location free from the risk of dripping or splashing water.
To prevent electric shock, do not remove the protective cover of the primary or handle the wiring.
The fitting and handling of this device must be carried out by in the absence of electricalauthorised personnel
current.
To avoid damage, the power supply unit must be firmly secured in place.
Installing the lock release:
INSTALLATION OF THE LOCK RELEASE
DIN rail.
DIN rail.
DIN rail.
DIN 46277
DIN rail latch release.
M 4 x 8
3,5 x 25
DIN-7972
DIN-963
IMPORTANT:
-The lock release must be 12V DC orAC (Golmar).
(See p. 27 forAC lock release and pp. 14-27 for DC lock release).
-The kit is supplied with two varistors. If connecting an AC lock release to one of the outputs, fit the varistor
supplied directly to the lock release terminals to ensure the device functions correctly.
If the lock release is to be fitted to a metal door, use a Ø3.5mm drill bit and
thread the hole made. For wooden doors, use a Ø3mm drill bit.
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

WIRING DIAGRAMS:
One-apartment installation with VESTA2 monitor and Golmar DC lock release.
14
Lock release
12 Vcc/270mA.max.
AP
ON
1 2 3
SW1
( )1
( )1
Access panel
BUS
CODE 0
Two-apartment installation with 1 VESTA2 monitor per house and Golmar DC lock release.
Configure the end of line in
the last monitor.
DIP 6 to ON.
*
( )1
Access panel
BUS
CODE 0
Distances and
cross-sections:
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
50m
B
10m
C
65m 60m 15m
Cable
BUS
CODE 16
FA- 2GB /A
A
B
C
APARTMENT 1APARTMENT 2
*
*
Configure the end of line in
the last monitor.
DIP 6 to ON.
*
Distances and
cross-sections:
A
B
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
50m
B
10m
C
65m 60m 15m
Cable
C
APARTMENT 1
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
FA- 2GB /A
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
( )2
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
( )2
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
ON
1 2 3
SW1
AP- C1 NA1 AP+ CV- BUSBUS
CV+
AP
( )1
AP- C1 NA1 AP+ CV- BUSBUS
CV+
Lock release
12 Vcc/270mA.max.
( )1
VESTA2
VESTA2
VESTA2
VESTA2VESTA2
VESTA2
Important: For AC lock release, 2nd AC lock release or automatic gate, see wiring diagrams p. 27.
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE

WIRING DIAGRAMS:
One-apartment installation with VESTA2 monitors in parallel (In-Out) and Golmar DC lock release.
15
Two-apartment installation with VESTA2 monitors in parallel (In-Out) and Golmar DC lock release.
( )1
Distances and cross-sections:
A
B
C
Configure the end of line in the last monitor.
DIP 6 to ON.
*
A
B
C
Distances and cross-sections:
BUS
CODE 1
BUS
CODE 2
BUS
CODE 3
BUS
CODE 0
BUS
CODE 1
BUS
CODE 16
BUS
CODE 17
BUS
CODE 0
APARTMENT 1APARTMENT 2
*
*
IMPORTANT: Maximum 4 monitors in parallel (without distributors) per installation.
IMPORTANT: Maximum 4 monitors in parallel (without distributors) per installation.
APARTMENT 1
FA- 2GB /A
CN
Mains
100~240Vac
N L
BUS (M) BUS(PL)
FA- 2GB /A
L
CN
Mains
100~240Vac
N L
BUS (M) BUS(PL)
FA- 2GB /A
L
FA- 2GB /A
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
Configure the end of line in the last monitor.
DIP 6 to ON.
*
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
50m
B
10m
C
65m 60m 15m
Cable
( )2
Lock release
12 Vcc/270mA.max.
AP
ON
1 2 3
SW1
( )1
( )1
Access panel
AP- C1 NA1 AP+ CV- BUSBUS
CV+
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
50m
B
10m
C
65m 60m 15m
Cable
( )2
Access panel
ON
1 2 3
SW1
AP
( )1
AP- C1 NA1 AP+ CV- BUSBUS
CV+
Lock release
12 Vcc/270mA.max.
( )1
VESTA2
VESTA2
VESTA2 VESTA2 VESTA2
VESTA2 VESTA2 VESTA2 VESTA2
VESTA2
VESTA2
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
Important: For AC lock release, 2nd AC lock release or automatic gate, see wiring diagrams p. 27.

WIRING DIAGRAMS:
One-apartment with 6 VESTA2 monitors, 2 DP-GB2A distributors and Golmar DC lock release.
16
Configure the end of line in
the last monitor.
DIP 6 to ON.
**
Configu the end of line inre
the last distributor.
Switch to ON.
*
Distances and cross-sections:
DP-GB2A
A
C
B
C
(1)
D
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
55m
B
30m
C
65m 60m 30m
Cable
10m
D
15m
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
FA- 2GB /A ( )2
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
Lock release
12 Vcc/270mA.max.
AP
ON
1 2 3
SW1
( )1
( )1
Access panel
AP- C1 NA1 AP+ CV- BUSBUS
CV+
BUS
BUS
BUS
BUS
BUS BUS
BUS BUS
D
C
B
A
DP- 2GB A
BUS BUS
End of line
ON
End of line
OFF
CODE 3 CODE 2
CODE 1 CODE 0
CODE 5 CODE 4
** **
** **
** **
*
BUS BUS
BUS BUS
D
C
B
A
DP- 2GB A
VESTA2 VESTA2
VESTA2 VESTA2
VESTA2 VESTA2
VESTA2VESTA2
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
Important: For AC lock release, 2nd AC lock release or automatic gate, see wiring diagrams p. 27.

WIRING DIAGRAMS:
One apartment with 6 VESTA2 monitors, 3 D2L-GB2 distributors and Golmar DC lock release.
17
Configure the end of line in
the last monitor.
DIP 6 to ON.
**
Remove the jumper from all
of the distributors except
the last.
*
Set the jumper in this position for
4.3” GB2 monitors of all of the
D2L-GB2 distributors.
(1)
Distances and cross-sections:
D2L- 2GB
A
C
B
C
D
( )2
FA- 2GB /A
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
55m
B
30m
C
65m 60m 30m
Cable
10m
D
15m
( )3
( )3 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
Lock release
12 Vcc/270mA.max.
AP
ON
1 2 3
SW1
( )2
( )2
Access panel
AP- C1 NA1 AP+ CV- BUSBUS
CV+
VESTA2VESTA2
BUS BUS
BUS BUS
D2
D1
D2L- 2GB
BUS BUS
BUS BUS
BUS BUS
D2
D1
D2L-GB2
BUS BUS
End of
line
ON
CODE 3 CODE 2
** **
*
BUS BUS
BUS BUS
D2
D1
D2L- 2GB
BUS BUS
CODE 1 CODE 0
** **
OFF
(1)
End of
line
OFF
End of
line
(1)
(1)
CODE 5 CODE 4
** **
VESTA2VESTA2
VESTA2VESTA2
VESTA2VESTA2
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
Important: For AC lock release, 2nd AC lock release or automatic gate, see wiring diagrams p. 27.

WIRING DIAGRAMS:
Two apartments with 6 VESTA2 monitors, 2 DP-GB2A distributors and Golmar DC lock release.
18
BUS BUS
BUS BUS
D
C
B
A
DP- 2GB A
End of line
CODE 0
**
Distances and cross-sections:
DP-GB2A
A
C
B
C
(1)
D
BUS BUS
BUS BUS
D
C
B
A
DP- 2GB A
End of line
CODE 17
**
OFF
APARTMENT 2APARTMENT 1
FA- 2GB /A
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
55m
B
30m
C
65m 60m 30m
Cable
10m
D
15m
( )2
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
BUS
CODE 18
**
BUS
ON
BUS
CODE 1
**
BUS
Access panel
ON
1 2 3
SW1
AP
( )1
AP- C1 NA1 AP+ CV- BUSBUS
CV+
Lock release
12 Vcc/270mA.max.
( )1
Configure the end of line in the last monitor.
DIP 6 to ON.
**
Configur the end of line in the last distributor.e
Switch to ON.
*
VESTA2
VESTA2
VESTA2
VESTA2
BUS
CODE 2
**
VESTA2
BUS
CODE 16
**
VESTA2
VESTA2VESTA2
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
*
Important: For AC lock release, 2nd AC lock release or automatic gate, see wiring diagrams p. 27.

WIRING DIAGRAMS:
Two apartments with 6 VESTA2 monitors, 4 D2L-GB2 distributors and Golmar DC lock release.
19
BUS BUS
BUS BUS
D2
D1
D2L-GB2
( )2
BUS BUS
BUS BUS
D2
D1
D2L-GB2
OFF
End of
line
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
55m
B
30m
C
65m 60m 30m
Cable
10m
D
15m
( )3
( )3 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
Set the jumper in this position for 4.3” GB2
monitors of all of the D2L-GB2 distributors.
(1)
(1)(1)
Configure the end of line in the last monitor.
DIP 6 to ON.
**
Remove the jumper from all of the distributors
except the last.
*
Distances and cross-sections:
DP-GB2A
A
C
B
C
D
FA- 2GB /A Access panel
ON
1 2 3
SW1
AP
( )2
AP- C1 NA1 AP+ CV- BUSBUS
CV+
Lock release
12 Vcc/270mA.max.
( )2
APARTMENT 2APARTMENT 1
VESTA2VESTA2
BUS BUS
BUS BUS
D2
D1
D2L-GB2
BUS BUS
BUS BUS
D2
D1
D2L-GB2
End of
line
ON
*
OFF
End of
line
(1)(1)
CODE 0
**
CODE 17
**
BUS
CODE 18
**
BUS
BUS
CODE 1
**
BUS
VESTA2
VESTA2
VESTA2
VESTA2
BUS
CODE 2
**
VESTA2
BUS
CODE 16
**
VESTA2
OFF
End of
line
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
Important: For AC lock release, 2nd AC lock release or automatic gate, see wiring diagrams p. 27.

WIRING DIAGRAMS:
One-apartment installation with VESTA7 monitor and Golmar DC lock release.
20
Lock release
12 Vcc/270mA.max.
AP
ON
1 2 3
SW1
( )1
( )1
Access panel
BUS
CODE 0
Two-apartment installation with 1 VESTA7 monitor per house and Golmar DC lock release.
Configure the end of line in
the last monitor.
DIP 6 to ON.
*
( )1
Access panel
BUS
CODE 0
Distances and
cross-sections:
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
50m
B
10m
C
65m 60m 15m
Cable
VESTA7
BUS
CODE 16
FA- 2GB /A
VESTA7
A
B
C
APARTMENT 1APARTMENT 2
*
*
Configure the end of line in
the last monitor.
DIP 6 to ON.
*
Distances and cross-sections:
A
B
Twisted pair 2x0.75mm2
Twisted pair 2x1mm2
6 m0
A
50m
B
10m
C
65m 60m 15m
Cable
C
APARTMENT 1
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
FA- 2GB /A
Mains
100~240Vac
N L
CN
BUS (M) BUS(PL)
FA- 2GB /A
L
VESTA7
VESTA7
VESTA7
VESTA7
( )2
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
2
( )2
( )2 Distances with Golmar RAP-2150 cable
(twisted pair 2x1mm ).
2
ON
1 2 3
SW1
AP- C1 NA1 AP+ CV- BUSBUS
CV+
AP
( )1
AP- C1 NA1 AP+ CV- BUSBUS
CV+
Lock release
12 Vcc/270mA.max.
( )1
JAZZ GB2 VIDEO DOOR ENTRY SYSTEM KIT - HOUSE
Important: For AC lock release, 2nd AC lock release or automatic gate, see wiring diagrams p. 27.