Gorenje EC5355XPA Technical manual

EN
EC5355XPA
EC5321WC
EC5341WC
EC5341SC
EC5342WC
EC5354WC-B
EC5351WA
EC5352XA
EC5351XA
EC5352WPA
gorenje
www.gorenje.com
DETAILED INSTRUCTIONS
FOR USE OF AN ELECTRIC
FREE STANDING COOKER

EN 1
We thank you for your
trust and the purchase of our appliance.
This detailed instruction manual is supplied
to make the use of this product easier. The
instructions should allow you to learn about
your new appliance as quickly as possible.
Make sure you have received an
undamaged appliance. If you do find
transport damage, please contact the seller
from which you purchased the appliance, or
the regional warehouse from which it was
supplied.
Instructions for use are also available at our
website:
http://www.gorenje.com
Important information
Tip, note
GORENJE gospodinjski aparati, d.o.o.
Partizanska cesta 12
SI-3320 Velenje, SLOVENIA
[e-mail]

EN 2
IMPORTANT SAFETY INSTRUCTIONS
CAREFULLY READ THE INSTRUCTIONS AND SAVE THEM
FOR FUTURE REFERENCE.
This appliance may only be used by children aged 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if supervision or
instructions are provided to them concerning use of the appliance
in a safe way and if they understand the hazards involved. Do not
let the children play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
WARNING: The appliance and some of its accessible parts may
become very hot during use. Be careful not to touch the heating
parts of the appliance. Children younger than 8 years of age shall
be kept away unless continuously supervised.
WARNING: The accessible parts of the appliance may become hot
during use. Young children should be kept away from the oven.
WARNING: Danger of fire: do not store items on the cooking
surfaces.
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire. NEVER try to extinguish a fire
with water, but switch off the appliance and then cover flame e.g.
with a lid or a fire proof blanket.
Only use the temperature probe recommended for use in this oven.
CAUTION: The cooking process and a short term cooking process
has to be supervised continuously.
WARNING: If the surface is cracked, switch off the appliance to
avoid the possibility of electric shock.

EN 3
CAUTION: possibility of tilting.
WARNING: In order to prevent tipping of
the appliance, stabilising means must be
installed. Refer to the instructions for
installation.
WARNING: Before replacing the light bulb, make sure the
appliance has been disconnected from the mains power, in order
to prevent the hazard of an electric shock.
Appliance must not be installed behind a decorative door in order
to avoid overheating.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the oven door glass/ the glass of hinged lids of the hob (as
appropriate), since they can scratch the surface, which may result
in shattering of the glass.
Do not use steam cleaners or high-pressure cleaners to clean the
appliance, as this may result in an electric shock.
The appliance is not intended to be controlled by external timers or
separate remote control system.
WARNING: Use only hob guards designed by the manufacturer of
the cooking appliance or indicated by the manufacturer of the
appliance in the instructions for use as suitable or hob guards
incorporated in the appliance. The use of inappropriate guards can
cause accidents.

EN 4
Make sure the lid is clean and that there is no liquid spilt on it
before raising it. The lid may be lacquer-coated or glass. It may
only be closed when the cooking zones have completely cooled
down.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
CAUTION: This appliance is for cooking purposes only. It must not
be used for other purposes, for example room heating.
The appliance is intended to be placed directly on the floor, without
any supports or plinths.
Do not install the appliance near powerful sources of heat, such as
solid fuel stoves, because high temperature near them can
damage the appliance.
The appliance may only be connected to the mains power by an
authorized service technician or expert. Clamps (instead of
connecting cable) should be protected by a clamp cover (see
additional equipment). Tampering with the appliance or non-
professional repair thereof may result in risk of severe injury or
damage to the product.
If the power cords of other appliances located near this appliance
are caught in the oven door, they may be damaged, which may in
turn result in a short circuit. Therefore, keep the power cords of
other appliances at a safe distance.
Do not line the oven walls with aluminium foil and do not place
baking trays or other cookware on the oven bottom. Aluminium foil
would prevent air circulation in the oven, hinder the cooking
process, and ruin the enamel coating.

EN 5
Oven door become very hot during operation. A third glass is
installed for extra protection, reducing the temperature of the
outside surface (only with some models).
Oven door hinges may be damaged when under excessive load.
Do not place heavy pans on open oven door and do not lean
against open oven door when cleaning the oven cavity. Never
stand on the open oven door and do not let children sit on it.
Make sure the vents are never covered or obstructed in any other
way.
NOTICE In case the appliance is equipped with a glass or glass
ceramic cooking surface. In case of breakage:
−Switch off all electric heating elements and disconnect the
appliance from the mains.
−Do not touch the surface of appliance.
−Do not use the appliance.
For appliance connection use a 5x1,5mm2cord with mark H05VV-
F5G1,5 or better. Cord must be installed by service agent or
similary quialified person.
Appliance must be connected to fixed wiring which is in
accordance with the witing rules.
Appliance must be connected to fixed wiring which has
incorporated means of disconnection. Fixed wiring must be made
in accordance with the wiring rules.
BEFORE CONNECTING THE APPLIANCE
Carefully read the instructions for use before connecting the
appliance. Repair or any warranty claim resulting from incorrect
connection or use of the appliance shall not be covered by the
warranty.

EN 6
APPLIANCE LID
Make sure the lid is clean and that there is no liquid
spilt on it before raising it. The lid may be lacquer-
coated or glass. It may only be closed when the
cooking zones have completely cooled down.
Do not close the lid when the burner is lit!
The symbol on the product or its
packaging indicates that glass lids
may shatter when heated.
Turn off all the burners before shutting the lid.
APPLIANCE DRAWER
Do not store combustible, explosive,
volatile or temperature-sensitive items
(such as paper, dish cloths, plastic
bags, cleaners or detergents and spray
cans) in the oven's storage drawer, as
they can ignite during over operation
and cause a fire.
OVEN EQUIPMENT AND
ACCESSORIES
(depending on the model)
WIRE GUIDES
The wire guides allow preparation of the food on four
levels (please note that the levels/ guides are
counted from the bottom up).
Guides 3 and 4 are intended for grilling.
Appliance operation is safe with and without tray
guides.
TELESCOPIC PULL-OUT GUIDES
Telescopic pull-out guides may be fitted for the 2nd,
3rd, and 4th level. Pull-out guides can be partly or
fully extendible.
EMBOSSED
The oven has stamped side grooves in four levels
for inserting of the grid and baking sheets.
OVEN DOOR SWITCH
The switch deactivates oven heating and the fan
when the oven door is opened during the cooking
process. When the door is closed, the switch turns
the heaters back on.
COOLING FAN
The appliance is fitted with a cooling fan that cools
the housing and the appliance control panel.
The cooling fan is in operation when the oven is in
operation.
The appliance and some of the
accessible parts tend to heat up during
cooking. Use oven mitts.
GRID
There is a safety latch on the grid. Therefore,
lift the grid slightly at the front when pulling it out
from the oven.
The grid or the tray should always be inserted into
the groove between the two wire profiles.
With telescopic extendible guides, first pull out the
guides of one level and place the grid or the baking
tray onto them. Then, push them in with your hand
as far as they will go.
Close the oven door when the telescopic
guides are retracted all the way into the oven.
As baking accessories heat up, their form may
change. This does not affect their functionality and
their original form will be restored when they cool
down.
CONTROL UNIT
(depending on the model)
EC5355XPA
EC5321WC, EC5341WC, EC5341SC, EC5342WC,
EC5354WC-B, EC5351WA, EC5352XA,
EC5351XA, EC5352WPA
1. Cooking zone knob front left
2. Cooking zone knob rear left
3. Cooking zone knob rear right
4. Cooking zone knob front right
5. Cooking system selector knob
6. Oven temperature knob
7. Electronic timer

EN 7
PUSH-PULL KNOBS
(depending on the model)
Softly press the knob so it lifts from the control
panel.
Knobs can be pushed back into the control
panel only when they are in "zero" position.
USING THE APPLIANCE
BEFORE USING THE APPLIANCE FOR
THE FIRST TIME
Upon receiving the appliance, remove all parts,
including any transport equipment, from the oven.
Clean all accessories and utensils with warm water
and regular detergent. Do not use any abrasive
cleaners.
If your hob has a glass ceramic surface, clean it with
a damp cloth and some washing-up liquid. Do not
use aggressive cleaners, such as abrasive cleaners
that could cause scratches, abrasive dishwashing
sponges, or stain removers.
If your cooking hob has conventional cooking zones,
switch them on to the maximum power for 3 to 5
minutes without any cookware on them. As the
cooking zones heat up, some smoke may appear on
the cooking hob surface. Thus, the cooking zone
finish reaches its maximum resistance.
When the oven heats up for the first time, the
characteristic smell of a new appliance will be
emitted. Ventilate the room thoroughly during the
first operation.
COOKING HOB
ELECTRIC HOBS
−Make sure the cooking zone and the cookware
bottom is clean and dry. This will allow better
conduction of heat and prevent any damage to
the heating surface.
−Overheated fat and oil on the cooking zones may
ignite. Therefore, be careful when cooking with fat
or oil and always control the cooking process.
−Do not place wet cookware or lids covered in
steam on the cooking zones. Moisture may
damage the cooking zones.
−Do not cool down the hot cookware by placing it
on the cooking zones that were not in use,
because the condensate that will appear under
the cookware bottom may aid corrosion.
Rotate the knob to switch on the cooking zone.
Cooking zone heating power can be set in steps
from 1 to 6.
Switch off the cooking zone 3 –5 minutes
before the end of the cooking process to make use
of the residual heat and save power.
Rapid cooking zones (only with some models)
can operate with greater power than regular cooking
zones, which means they can heat up more quickly.
These cooking zones are indicated with a red dot in
the middle. After repeated heating and cleaning, this
dot may disappear.
In case of prolonged use of cast iron
plates, the area of the plate and the
edge of the cooking zone may
discolour. Service in such case is not
covered by the warranty.
GLASS CERAMIC HOB
The power of the hob can be set in levels from 1 to
6. The hobs are connected in different time intervals,
depending on the set level. Overheating of the
surface under the glass ceramic panel is prevented
by the temperature limiter.
CONTROL OF THE TWO-RING COOKING
ZONE
The area of the two-ring cooking zone can adapt to
the size and the form of your cookware.
To activate the larger heating zone, rotate the
cooking zone knob as far as it will go (a click will be
heard), then set the desired power level.
HI-LIGHT COOKING ZONES
Hi-Light cooking zones differ from the conventional
zones by rapid heating; therefore, the cooking
process begins very soon.
RESIDUAL HEAT INDICATOR
Each hob is equipped with a control light that stays
on also after the hob is turned off, if the hob is still
hot. When the cooking zone cools down, the signal
light goes out. The residual heat indicator is also lit
up if a hot pot or pan is placed on a cool cooking
zone.
GLASS CERAMIC COOKING SURFACE
−The hob is resistant to temperature changes.
−The glass-ceramic plate is very solid but it is not
unbreakable. The plate can break when an object
falls with its edge on the plate. Such damage
comes out immediately or after a while.

EN 8
Disconnect the damaged hotplate from the main
immediately and do not use it.
−Using the glass ceramic hob as a storage area
may result in scratches or other damage to it.
−Do not use aluminium or plastic cookware on hot
cooking zones. Do not place any plastic objects
or aluminium foil on the glass ceramic hob.
−Make sure the cooking zone and the cookware
bottom is clean and dry. This will allow better
conduction of heat and prevent any damage to
the heating surface. Do not place empty
cookware on the cooking zone.
TIPS REGARDING YOUR COOKWARE
−Use quality cookware with flat and stable bottom.
−Pan bottom and cooking zone diameters should
be the same.
−Tempered glass cookware with special ground
bottom may be used on the cooking zones if its
diameter fits that of the cooking zones. Cookware
with larger diameter may crack due to thermal
tension.
−Make sure the pot or pan is in the middle of the
cooking zone.
−When using a pressure cooker, keep an eye on it
until the right pressure is reached. First, set the
cooking zone to maximum power; then, following
the pressure cooker manufacturer's instructions,
use the relevant sensor to decrease the cooking
power at the right time.
−Make sure there is enough liquid in the pressure
cooker, or any other pot or pan. Due to
overheating, using an empty pot on the cooking
zone may result in damage to both the pot and
the cooking zone.
−When using special cookware, observe the
manufacturer's instructions.
ENERGY SAVING TIPS
−Diameter of the pot and pan bottoms should
match the diameter of the cooking zone. If the pot
or pan is too small, a part of the heat will be lost,
and the cooking zone may be damaged.
−If the cooking process allows, use a lid.
−Cookware should be suitably sized given the
amount of food. When you cook a small amount
of food in a large pot or pan, more energy is lost.
−If a dish takes a long time to cook, use a pressure
cooker.
−Vegetables, potatoes etc. may be cooked in a
smaller amount of water. The food will cook just
as well, as long as the pot is tightly closed with a
lid. After bringing the water to a boil, reduce the
heat to a level that just sufices to maintain a slow
simmer.
If sugar or food with high sugar content
is spilled over a hot class ceramic hob,
immediately wipe the hob or remove
the sugar with a scraper, even if the
cooking zone is still hot. This will
prevent any damage to the class
ceramic surface.
Do not use detergents and other cleaners to
clean a hot glass ceramic hob as this could
damage the surface.
ELECTRONIC TIMER
User interface
1. Timer function display
2. Power on light indicator
3. Temperature light indicator
4. ʺLessʺ button
5. Time button
6. ʺMoreʺ button
Set the current time
When you connect the appliance to the mains
electricity for the first time, the display lights up. After
three seconds the clock symbol and ʺ12:00ʺwill
flash on the display.
You can set the time values by pressing back ʺ ʺ or
ʺ ʺ forward icons. After 10 sec. display
automatically confirm the settings, appliances is
ready to use.
The current time can be set:
−when the appliance is connected to the mains for
the first time,
−in standby, when you press the time button twice,
−after power fallout.

EN 9
Setting a preparation time
Select an oven function using the ʺoven function
knobʺand set the temperature.
Press the ʺtimer buttonʺto select the
ʺpreparation timeʺfunction.
The pictogram for the ʺpreparation timeʺlights up
on the display.
Press the less ʺ ʺ or more ʺ ʺ button to set the
preparation time.
The settings are automatically confirmed after 10
seconds. The settings can also be confirmed by
pressing the "timer button" .
The elapsed preparation time will be displayed.
After turning on the oven using the "oven
function switch", the electronic timer automatically
(after 3 seconds) offers the option of setting the
duration of baking. The display flashes and the
ʺpreparation time" symbol is lit up. If duration is
not set within 5 seconds, the timer switches into
standby and duration of baking is not under time
control. The current time is displayed.
After the set baking duration expires, a sound signal
is heard and the oven is switched off. The oven can
be turned off with the "oven function switch". To stop
the sound signal, press any button on the timer.
If the oven is not turned off and the sound
signal is stopped by pressing any button, the oven
restarts and the baking continues.
Setting a preparation time and end time
Select an oven function using the ʺoven function
knobʺand set the temperature.
Press the ʺtimer buttonʺto select the
ʺpreparation timeʺfunction.
The pictogram for the ʺpreparation timeʺlights up
on the display.
Press the less ʺ ʺ or ʺ ʺ more button to set the
preparation time.
Press the ʺtimer buttonʺto save the set time.
Press the ʺtimer buttonʺ again twice
The pictogram for the ʺend timeʺlights up on the
display.
Press the less ʺ ʺ or more ʺ ʺ button to set the
The settings are automatically confirmed after 10
seconds. The settings can also be confirmed by
pressing the "timer button" .
The oven starts operating before the planned "end
time" depending on the desired ʺpreparation time"
. When the oven achieves the set "end time"
the oven is switched off.
Example: The set "duration of baking" is 30
minutes. The end time is at 12:00. The oven starts
operating at 11:30 and the remaining time is
displayed on the screen. At 12:00 the oven
automatically switches off.
After the set baking duration expires, a sound signal
is heard and the oven is switched off. The oven can
be turned off with the "oven mode selection switch".
To stop the sound signal, press any button on the
timer.
ʺTIMER ALARMʺ function
The ʺtimer alarmʺfunction can be used
independently of the oven.
The highest possible setting is 23 hours and 59
minutes.
The last minute of the run time is displayed in
seconds.
After the set baking duration expires, a sound signal
is heard. To stop the sound signal, press any key on
the programme clock.
The programme clock switches into the standby
mode and the display shows the current time.
You can cancel all timer functions by setting the time
to ʺ0ʺ.
If the appliance has been inactive for a few minutes,
it will switch to standby. The current time appears
and the selected timer function will light up.
ADDITIONAL FUNCTIONS
Child lock
With the child lock you can lock the oven while in
operation. You can also lock the programme clock
while baking with a set programme, thus preventing
unwanted use of the oven.
The child lock is activated by pressing the "timer
button" button for 5 seconds.
The display will read ‘‘Locʺ for 5 seconds.
This indicates that all functions are locked.
To deactivate the child lock, press the button again
for a few seconds.
Once the child lock is activated and no timer
function has been set (only the clock is displayed),

EN 10
the oven will not work. If the child lock is activated
after a timer function has been set, the oven will
work; however, the settings cannot be changed.
When the child lock is activated, oven functions or
additional functions cannot be changed. The cooking
process can only be ended by turning the ʺOven
function knobʺto ʺ0ʺ. The child lock remains
activated even after the oven has been switched off.
The child lock needs to be deactivated before you
can select a new programme.
Sound signal
The volume of the sound signal can be set if no
timer function has been activated. The appliance is
in standby mode and only the current time is
displayed.
Press and hold the less ʺ ʺ button for 5 seconds.
ʺVollʺ appears on the display followed by several
bars that are fully lit.
Press the less ʺ ʺ or more ʺ ʺ button to select one
of three volume levels (one, two or three bars) or no
sound (Off).
The settings are automatically confirmed after 5
seconds. The settings can also be confirmed by
pressing the "timer button" .
Reduce display contrast
Press and hold the more ʺ ʺ button for 5 seconds.
ʺBriʺappears on the display followed by several bars
that are fully lit.
Press the less ʺ ʺ or more ʺ ʺ button to adjust the
dimming level (one, two or three bars).
The settings are automatically confirmed after 5
seconds. The settings can also be confirmed by
pressing the "timer button" .
Power on light indicator
The light in the oven lights when the oven function is
selected using the "oven mode selection switch".
Temperature light indicator
The light turns on in the moment when the oven is
heated up to the set temperature and remains on
until the oven is switched off or when the baking
period ends.
Error indication
In case of error, display shows “ERR”text and
number of mistake. Please inform service
department.
OVEN
OPERATING THE OVEN
The oven can be operated with the knob for "oven
mode selection" to select the function and
"temperature setting" to set the temperature.
Rotate the knob (left and right) to select COOKING
SYSTEM (see program table).

EN 11
Settings can also be changed during the
cooking process.
OVEN OPERATION
Operation temperature is set with the temperature
selector, ranging from 50 - 275°C. Clockwise
rotation of the selector sets higher temperature, and
vice versa, anticlockwise turning reduces the
temperature.
Forcible overturning of the zero position
will lead to the thermostat damage!
SWITCHING OFF THE OVEN
Turn the COOKING SYSTEM SELECTOR KNOB to
position "0".
System
Suggested
temperature °C
Description
Cooking systems
50-275
RAPID PREHEAT
Use this function if you wish to
heat the oven to the desired
temperature as quickly as
possible. This function is not
appropriate for cooking food.
When the oven heats up to the
desired temperature, the
heating process is completed.
200
UPPER AND BOTTOM
HEATER
The heaters in the bottom and
in the ceiling of the oven cavity
will radiate heat evenly into the
oven interior. Pastry or meat
can only be baked/roasted at a
single height level.
180
TOP HEATER
Only the heater on the oven
cavity ceiling will radiate heat
onto the food. Use it to brown the
upper side of your dish (final
browning).
180
BOTTOM HEATER
Only the heater on the bottom of
the oven cavity will radiate heat.
Use this heater to brown the
lower side of the dish.
230
GRILL
Only grill heater, a part of the
large grill set, will operate. This
system is used for grilling a
smaller amount of open
sandwiches or beer sausages,
and for toasting bread.
System
Suggested
temperature °C
Description
Cooking systems
230
LARGE GRILL
The upper heater and the grill
heater will operate. The heat is
radiated directly by the grill
heater installed in the oven
ceiling. To boost the heating
effect, the upper heater is
activated as well. This
combination is used for grilling
a smaller amount of open
sandwiches, meat or beer
sausages, and for toasting
bread.
170
GRILL WITH FAN
Grill heater and the fan will
operate. This combination is
used to grill meat and to roast
larger chunks of meat or
poultry at a single height level.
It is also appropriate for dishes
au gratin and for browning to a
crispy crust.
170
TOP HEATER AND FAN
The top (upper) heater and the
fan will operate. Use this system
to roast larger chunks of meat
and poultry. It is also suitable for
dishes au gratin.
200
HOT AIR AND BOTTOM
HEATER
The bottom heater, the round
heater, and the hot air fan will
operate. This is used to bake
pizza, moist pastry, fruitcakes,
leavened dough and
shortcrust.
180
HOT AIR
Round heater and the fan will
operate. The fan installed in
the back wall of the oven
cavity makes sure the hot air
constantly circulates around
the roast or pastry. This mode
is used for roasting meat and
baking pastry at several levels
simultaneously.
180
BOTTOM HEATER AND FAN
This is used for baking
leavened but low-rising pastry
and for preserving fruit and
vegetables.
180
TOP AND BOTTOM HEATER
WITH FAN
Both heaters and the fan are
activated. The fan allows even
circulation of hot air inside the
oven. It is used for baking pastry,
for defrosting, and for drying fruit
and vegetables.

EN 12
System
Suggested
temperature °C
Description
Cooking systems
60
PLATE WARMER
Use this function to reheat
your dinnerware (plates, cups)
before serving food in it to
keep the food warm longer.
180
GENTLEBAKE *
This feature allows gentle,
slow, and even baking that
leaves the food soft and juicy.
It is suitable for roasting meat,
cooking fish, and baking pastry
on a single rack.
-
DEFROSTING
The air circulates with no
heaters activated. Only the fan
will be activated. This is used
to slowly thaw frozen food.
70
AQUA CLEAN
Only the bottom heater will
radiate heat. Use this function
to remove stains and food
residues from the oven. The
program takes 30 minutes.
* It is used for determining the energy efficiency
class pursuant to the EN 60350-1 standard.
DESCRIPTIONS OF SYSTEMS
Heating an empty oven consumes a lot of energy.
Hence, baking several types of pastry or several
pizzas successively will save a lot of energy as the
oven will already have been preheated.
Use dark, black silicon-layered or enamel-coated
baking sheets and trays as they conduct the heat
very well.
When using parchment paper, make sure it is
resistant to high temperatures.
When preparing food, a lot of steam is formed inside
the oven, which is drained through the chimney at
the back of the appliance. The steam might
condense on the door and lid of the appliance
(depending on the model). This is a standard
phenomenon which has no effect on the operation of
the appliance. After the end of the cooking proces,
wipe the overflowing condensed water with a cloth.
Switch off the oven approximately 10 minutes
before the end of the cooking process to save
energy by making use of the accumulated heat.
Do not cool the food in a closed oven to prevent
condensation (dew).
Guides cooking levels
COOKING SYSTEMS
OVEN LIGHTING
With all modes of operation, the oven lighting is
turned on automatically when the operation mode is
selected.
RAPID PREHEATING
Use this function to heat the oven to the desired
temperature as quickly as possible. This mode is not
appropriate for cooking.
−Turn the ʺOven function knobʺto the ʺquick
preheatʺposition.
−Set the oven to the desired temperature using the
ʺtemperature dial knobʺ.
UPPER AND BOTTOM HEATER
The heaters in the bottom and in the ceiling of the
oven cavity will radiate heat evenly into the oven
interior. Pastry and meat can be cooked on one
shelf leve only.
Roasting meat
Use enamel coated, tempered glass, clay, or cast
iron pan or tray. Stainless steel trays are not suitable
as they strongly reflect the heat.
Baking pastry
Only use one level and dark baking sheets or trays.
In light-coloured baking sheets or trays, the
browning of the pastry will be poorer, as such
equipment will reflect the heat. Always place the
baking trays on the grid. If you are using the
supplied baking sheet, remove the grid. Cooking
time will be shorter if the oven is preheated.
Do not insert the deep baking tray into
the first guide.
LARGE GRILL, GRILL
When grilling food with the large grill, the upper
heater and the grill heater fitted on the ceiling of the
oven cavity will operate (LARGE GRILL).
Only grill heater, a part of the large grill set, will
operate (GRILL).
Preheat the infrared (grill) heater for five minutes.

EN 13
Maximum temperature when using Grill and Large
grill is 230°C.
Supervise the cooking process at all times. The
meat may burn quickly due to high temperature.
Roasting with the grill heater is suitable for crispy
and low-fat cooking of bratwurst, cuts of meat and
fish (steaks, escalopes, salmon steaks or fillets etc.)
or toasted bread.
When grilling directly on the grid, smear it with oil to
prevent the meat from sticking onto it and insert it
into the 4th guide. Insert the drip tray in to the 1st or
2nd guide.
When grilling in a baking tray, make sure there is
enough liquid in the tray to prevent burning. Turn the
meat during cooking.
After grilling, clean the oven, the accessories, and
the utensils.
When baking trout, pat the fish dry with a paper
towel. Season on the inside; coat with oil on the
outside and place on the grid. Do not turn the fish
when grilling.
The grill shall only be used when the
oven door is closed.
Grill heater, grid, and other oven accessories get
very hot during grilling. Therefore, use oven mitts
and meat tongs.
Cooking with the rotisserie
(depending on the model)
Maximum temperature when using the rotisserie is
230°C.
Insert the skewer support into the 3rd guide from the
bottom and place the shallow baking sheet into the
bottom (1st) guide to serve as a drip tray.
Impale the meat on the skewer and tighten the
screws.
Place the skewer handle on the front skewer support
and insert the tip into the opening in the right hand
side of the rear oven cavity wall (the opening is
protected with a rotating cover).
Undo the skewer handle and close the oven door.
Switch on the oven and select the LARGE GRILL
system.
The grill shall only be used when the
oven door is closed.
Do not use the grill on position 4.
GRILL WITH FAN
In this operating mode, the grill heater and the fan
operate simultaneously. Suitable for grilling meat,
fish, and vegetables.
(See descriptions and tips for GRILL.)
HOT AIR AND BOTTOM HEATER
The bottom heater, the round heater, and the hot air
fan will operate. Suitable for baking pizzas, apple
pies, and fruitcakes.
HOT AIR
Round heater and the fan will operate. The fan
installed in the back wall of the oven cavity makes
sure the hot air constantly circulates around the
roast or pastry.
Roasting meat
Use enamel coated, tempered glass, clay, or cast
iron pan or tray. Stainless steel trays are not suitable
as they strongly reflect the heat.
Provide enough liquid during the cooking process to
prevent the meat from burning. Turn the meat during
roasting. The roast will remain juicier if you cover it.
Baking pastry
Preheating is recommended.
Biscuits and cookies can be baked in shallow baking
sheets on several levels simultaneously (2nd and
3rd).
Note that baking time can differ even with if the
baking sheets used are the same. The biscuits in the
upper baking sheet may be ready sooner than those
in the lower one.
Always place the baking trays on the grid. If you are
using the supplied baking sheet, remove the grid.
For even browning, make sure the biscuits are of the
same thickness.
Do not insert the deep baking tray into
the first guide.

EN 14
BOTTOM HEATER AND FAN
This is used for baking leavened but low-rising
pastry and for preserving fruit and vegetables. Use
the second guide from the bottom and a rather
shallow baking tray to allow the hot air to circulate
across the upper side of the dish.
Preservation
Prepare the food to be preserved and jars as usual.
Use jars with a rubber sealing ring and a glass
cover. Do not use jars with threaded or metal caps
or metal tins. Make sure the jars are of equal size,
filled with the same contents, and tightly sealed.
Pour 1 litre of hot water into the deep tray (approx.
70°C) and place 6 1-litre jars into the tray. Place the
tray into the oven on the second guide.
During preservation, observe the food and cook until
the liquid in the jars starts to simmer –when bubbles
appear in the first jar.
TOP AND BOTTOM HEATER WITH FAN
It is used for baking of all types of pastry, for
defrosting, and for drying fruit and vegetables.
Before placing the food into the preheated oven,
wait for the light to go off for the first time. For best
results, only bake on one shelf (level).
The oven should be preheated. Use the second or
the fourth guide, counting from the bottom up.aj.
DEFROSTING
In this mode, the air will circulate without any
heaters operating.
Food suitable for defrosting includes cakes with
heavy cream or butter-based cream, cakes and
pastry, bread and rolls, and deep-frozen fruit.
In most cases, it is recommended to remove the
food from the packaging (do not forget to remove
any metal clamps or clips).
Halfway through the defrost time, the pieces should
be turned over, stirred and separated if they were
frozen together.
PLATE WARMER
Use this function to reheat your dinnerware (plates,
cups) before serving food in it to keep the food warm
longer.
GENTLEBAKE
This feature allows gentle, slow, and even baking
that leaves the food soft and juicy. It is suitable for
roasting meat, cooking fish, and baking pastry on a
single rack.
AQUA CLEAN
Only the bottom heater will radiate heat. Use this
function to remove stains and food residues from the
oven. The program takes 30 minutes.
MAINTENANCE & CLEANING
Be sure to unplug the appliance from the
power supply and wait for the appliance
to cool down.
Children should not clean the appliance or
perform maintenance tasks without proper
supervision.
Stainless steel sheet front side of the housing
(depending on the model)
Clean this surface only with a mild detergent
(soapsuds) and a soft sponge that will not scratch
the finish. Do not use abrasive cleaners or cleaners
containing solvents as they may damage the
housing finish.
Lacquer-coated surfaces and plastic parts
(depending on the model)
Do not clean the knobs and buttons, door handles,
stickers, and rating/type plates with abrasive
cleaners or abrasive cleaning materials, alcohol-
based cleaners, or with alcohol. Immediately remove
any stains with a soft non-abrasive cloth and some
water, in order to avoid damaging the surface.
You may also use cleaners and cleaning materials
intended for such surfaces as instructed by their
respective manufacturers.
Enamel surfaces (oven, cooking hob)
Use a damp sponge with detergent for cleaning.
Fatty stains can be removed with warm water and
special detergent for enamel. Never clean
enamelled surfaces with abrasive means producing
irremovable damage to the appliance surface.
Glass surfaces
Do not use rough abrasive cleaning agents or sharp
metal scrapes for cleaning of oven door glass, as
they could crack the surface and causing the
breaking of glass. Clean the glass surfaces with
special means for glass, mirrors and windows.
CLEANING THE COOKING HOBS
Clean the area around the cooking zones with hot
water and some washing-up liquid.
For stubborn dirt, use a steel wool pad soaked with
detergent; then, rinse the hob and wipe it dry.

EN 15
Liquids containing salt, boiled-over liquids and
moisture have detrimental effect on the cooking
zones. Always clean the cooking zones,
Use regular cleaners and commercially available
conditioners to maintain the cooking zones. If the
cooking zone is slightly warm, the cleaner will
penetrate the pores more readily.
Cooking zone rings are made of stainless steel.
Because exposure to heat, they may take on a
yellowish hue after a certain period of use. This is a
normal physical phenomenon. The yellowish spots
may be removed with regular metal cleaners.
Aggressive dishwashing accessories are not
suitable for cleaning of these rims, as they may
cause scratches.
CLEANING THE GLASS CERAMIC
SURFACE
After each use, wait for the glass ceramic surface to
cool down and clean it. Otherwise, all remaining
impurities will burn onto the hot surface the next time
you use the hob.
For regular maintenance of the glass ceramic hob,
use special care products that create a protective
film on the surface to prevent the dirt from sticking
onto it.
Before each use of the glass ceramic surface, wipe
off the dust or any other impurities that could scratch
the surface, from both the hob and the pan bottom.
Steel wool, coarse cleaning sponges, and
abrasive powders may scratch the surface. The
surface may also be damaged by aggressive spray
cleaners and unsuitable liquid cleaners.
Signage may be worn when using aggressive or
abrasive cleaners or cookware with coarse or
damaged bottom.
Use a damp soft cloth to remove minor impurities.
Then, wipe the surface dry.
Remove water stains with a mild solution of vinegar.
However, do not use this solution to wipe the frame
(only with some models) as it may lose its sheen. Do
not use aggressive spray cleaners or descaling
agents.
Use special glass ceramic cleaners for stubborn dirt.
Observe the manufacturer's instructions. Be sure to
thoroughly remove any cleaner residues after the
cleaning process as they may damage the glass
ceramic surface when the cooking zones heat up.
Remove stubborn and burnt residues with a scraper.
Be careful when handling the scraper to prevent
injury.
Only use the scraper when dirt cannot be
removed with a wet cloth or special cleaners for
glass ceramic surfaces.
Hold the scraper at the correct angle (45° to 60°).
Gently press the scraper against the glass and slide
it over the signage to remove the dirt. Make sure the
plastic handle of the scraper (in some models) does
not come into contact with a hot cooking zone.
Do not press the scraper perpendicularly
against the glass and do not scratch the hob surface
with its tip or blade.
Immediately remove any sugar or sugar-laden food
from the glass ceramic hob using a scraper, even if
the hob is still hot, as sugar may permanently
damage the glass ceramic surface.
Discolouration of the glass ceramic surface
does not affect the operation or stability of the
surface. Such discolouration is most commonly a
result of food residues burnt onto the surface, or it
may be caused by some cookware materials (such
as aluminium or copper). Such discolouration is very
difficult to remove entirely.
Note: Discolouration and similar flaws only affect the
appearance of the hob and do not directly affect its
function. Removing such flaws shall not be covered
by the warranty.
OVEN
Clean the oven walls with a damp sponge and
detergent. To clean stubborn stains burned into the
oven wall use a special detergent for enamel. After
cleaning carefully wipe the oven dry. Clean the oven
only when it is completely cold. Never use abrasive
agents, because they will scratch enameled surface.
Wash the oven utensils with a sponge and

EN 16
detergent. You can also use special detergents to
remove rough stains or burns.
USING THE „AQUA CLEAN“
FUNCTION
Turn the COOKING SYSTEM SELECTOR KNOB to
position AQUA CLEAN . Set the
TEMPERATURE KNOB to 70°C.
Pour 0,6 l water into a baking tray and place it in the
lower guide.
After 30 minutes, food residues on the oven enamel
walls will have softened and they will be easy to
clean with a damp cloth.
Use the “AQUA CLEAN“system when
the oven has fully cooled down.
REMOVING AND CLEANING WIRE AND
TELESCOPIC EXTENDIBLE GUIDES
Only use conventional cleaners to clean the guides.
Hold the guides by the bottom side and pull them
towards the center of the oven cavity.
Remove them from the openings at the top.
Do not clean the extendible guides in
the dishwasher.
INSTALLING THE CATALYTIC INSERTS
Only use conventional cleaners to clean the guides.
Remove the wire guides or extendible guides.
(depending on the model)
Mount catalytic inserts onto the wire guides. The
upper part of the guides must be mounted into the
upper openings "A" in the catalytic inserts.
Place the wire guides with the catalytic inserts on
the upper openings in the side walls of the oven “A“.
Press them into the snap lock at the bottom “B“.
Do not wash the catalytic inserts in the
dishwasher.
CLEANING THE OVEN CAVITY CEILING
(depending on the model)
Upper grill heater is foldable to allow easier cleaning
of the oven cavity ceiling. Before cleaning the oven,
remove the trays, the grid, and the guides.
Pull the heater until the cross bar is released from
the supports on the left and right hand side of the
oven cavity.
Never use the heater when folded/ lowered. After
cleaning, observe the same procedure in the reverse
order to push back the heater until the cross bar
snaps back into place.
Disconnect the appliance from the
power mains.
The heater must be cool; otherwise,
there is danger of burns.
REPLACING THE BULB
The bulb is a consumable and therefore not covered
by warranty. Before changing the bulb, remove the
trays, the grid, and the guides.
Disconnect the appliance from the power mains!
Undo the bulb cover and pull out or undo the bulb.
Halogen lamp: G9, 230 V, 25 W. (regular bulb E14,
230 V, 25 W - depending on the model)
Use protection to avoid burns.
COMFORT DOOR CLOSING
(depending on the model)
Cookers are equipped with new secure door hinges
COMFORT. These special hinges guarantee very
quiet and gentle closing of the oven door.

EN 17
If the force applied to close the door is
too strong, the efficiency of the system
can be reduced or the system's safety
can be affected.
DOOR LOCK
(depending on the model)
Open the door lock by gently pushing it to the right
with your thumb while simultaneously pulling the
door outwards.
When the oven door is closed, the door
lock automatically returns to the initial
position.
REMOVING AND REPLACING THE OVEN
DOOR (depending on the model)
1. Open the oven door (up to end position).
2. Rotate the flaps of door hinges (in case of
conventional closing).
At COMFORT soft closing system, rotate the flaps
by 90°.
3. Slowly close the oven door until the flaps fit
together with the hinges in the side laths of the
door. At the angle of 15° (regarding to the closed
door position), slightly close the door and pull it
out from both hinges of the appliance.
Before replacing the door, always
check that the hinge flaps are correctly
placed in the side laths of the door.
You prevent the sudden closing of the
hinge so, which is connected to a
strong spring. The releasing of flap
causes the damaging of door and a
risk of injury.
Removing and replacing the oven door
(depending on the model)
1. Open the oven door (up to end position).
2. Raise up and turn the flaps.
3. Slowly close the oven door, lift it slightly and pull it
out from the both hinges of the appliance.
Provide these steps in reverse order at
returning the door back. If the door does not open or
close properly, make sure, that the hinges are
correctly located on their hooks.
REMOVING AND INSERTING THE OVEN
DOOR GLASS PANE (depending on the model)
Oven door glass pane can be cleaned from the
inside, but it has to be removed first. Remove the
oven door (see chapter "Removing and replacing the
oven door".
Slightly lift the supports on the left and right side of
the door (marking 1 on the support) and pull them
away from the glass pane (marking 2 on the
support).

EN 18
Hold the door glass pane by the lower edge; slightly
lift it so that it is no longer attached to the support;
and remove it.
To remove the third glass pane (only with some
models), lift and remove it. Also remove the rubber
seals on the glass pane.
To replace the glass pane, observe the
reverse order. The markings (semicircle) on the door
and the glass pane should overlap.
Removing and inserting the oven door glass
pane (depending on the model)
Screw out the screws on the door left and right sides
and pull out the upper lath. You can pull out the
glass pane of door now.
Provide these steps in reverse order at
returning the glass pane back.
TROUBLESHOOTING TABLE
Problem/error
Solution
The main fuse in
your home trips
often.
Call a service technician.
Make sure the power of all
appliances switched on does
not exceed the capacity of
the power mains in your
home.
The oven lighting
does not work.
The process of changing the
light bulb is described in the
chapter "Cleaning and
Maintenance".
The food is
underdone.
Did you choose the right
temperature and heating
system?
Is the oven door closed?
Repair or any warranty claim resulting from
incorrect connection or use of the appliance
shall not be covered by the warranty. In this
case, the user will cover the cost of repair.
INSTALLATION AND
CONNECTION INSTRUCTIONS
APPLIANCE PLACEMENT (mm)
The walls or furniture adjacent to the appliance
(floor, rear kitchen wall, side walls) have to be
temperature-resistant to at least 90°C.

EN 19
LEVELLING THE APPLIANCE AND
ADDITIONAL SUPPORT
(depending on the model)
ADJUSTING THE HEIGHT OF THE
COOKER (depending on the model)
The height of the cooker is 900 mm. You can adjust
the height of the appliance from 850 to 940 mm.
1. Put the cooker on the floor with back side.
2. Unscrew the screws, see arrows.
Torx T20
3. Set the desired height.
4. Screw the screws back together.
The cooker must be installed horizontally!
Follow these steps:
1. Rotate the height adjustment screws (see figure
1) to adjust the height of the cooker to the correct
position.
2. Adjust the wheels (see figure 2) by screwing them
with two screws at the front of the skirting board.
Check the horizontal position of the stove using a
spirit level.
3. Place the blind plugs into the holes in the front of
the skirting board (see Figure 3).
INSTALLATION OF THE LID
(depending on the model)
PREVENTION FROM TIPPING OVER (mm)