GPM WIMBLEDON OBDWIM46G User manual

GLOBAL PROCUREMENT AND MARKETING LIMITED
1
WIMBLEDON WINGBACK OTTOMAN BED
Assembly Instructions –Please keep for future reference
OBDWIM46G
Dimensions
No. people
Assembly Time
OW #
Width: HB 159 / FB 152 cm
90 mins (approx.)
OBDWIM46G
Length: 204 cm
Height: HB 130 / FB 29.5 cm
Important
•PLEASE READ THESE INSTRUCTIONS FULLY BEFORE STARTING ASSEMBLY
•PLEASE DO NOT THROW THE PACKAGING AWAY UNTIL YOU ARE SATISFIED WITH PURCHASE,
GOODS NEED TO BE RETURNED IN ORIGINAL PACKAGING.
If you need help or have damaged or missing parts, please email [e-mail]

2
Important –Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
•Check you have all the
components, parts, hardware
and tools listed on pages 7, 8
& 9.
•Remove all fittings from the
plastic bags and separate
them into their groups.
•Keep children and animals
away from the work area,
small parts could choke if
swallowed.
•Make sure you have enough
space to lay out the parts
before starting.
•Do not stand or put weight on
the product, this could cause
damage.
•Assemble the item as close to
its final position (in the same
room) as possible.
•Assemble on a soft, level
surface to avoid damaging the
unit or your floor.
•We do not recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit.
Only use hand screwdrivers.
•Dispose of all packaging
carefully and responsibly.
Care and Maintenance
•Only clean using a damp cloth and
mild detergent, do not use bleach or
abrasive cleaners.
•From time to time check that there
are no loose screws on this unit.
•This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
If you are unhappy with the product and wish to return it,
please follow the retailer’s returns procedure.

3

4

5

6

7
Components –Part List
If you have damaged or missing components,
email: [e-mail]

8
Components –Part List
Please check that you have all the components listed below before constructing your item.
Part No
Description
Qty
1
HEADBOARD
1
2
FOOTBOARD
1
3
SIDE RAIL (RIGHT)
1
4
SIDE RAIL (LEFT)
1
5
BED FRAME CROSS RAIL (HEADBOARD)
1
6-1
BED FRAME SIDE RAIL (RIGHT)
1
6-2
BED FRAME SIDE RAIL (LEFT)
1
7
BED FRAME CENTRE SUPPORT RAIL
1
8
BED FRAME CROSS RAIL (FOOTBOARD)
1
9
CENTRE SUPPORT LEG
2
10
SUPPORT BLOCK
2
11
FOLDING MECHANISM (LEFT)
1
12
FOLDING MECHANISM (RIGHT)
1
13
CORNER METAL ANGLE BRACKET
2
14
STRETCHER RAIL
1
15
MATTRESS STOPPER
2
16
SPRUNG WOOD SLAT
30
17
GAS LIFT (PNEUMATIC) CYLINDER
2
18
SPACER RAIL FOR FOLDING MECHANISM
2
19
NON-WOVEN FABRIC FOR BED BASE
1
20
HEADBOARD WING PANEL (RIGHT)
1
21
HEADBOARD WING PANEL (LEFT)
1
22
FOOT
4
If you have damaged or missing components,
email: [e-mail]

9
Components - Fixings
Please check that you have all the components listed below before constructing your item.
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
(A)
End Slat Cap
X30
(B)
Centre Slat Cap
X15
(C)
Bolt M8 x 20mm
X16
(D)
#4 x 35mm
X4
(E)
Flat Washer M8
X8
(F)
Nut
X4
(G)
#4 x 45mm
X8
(H)
Bolt M6 x 20mm
X 4
(I)
Wood Dowel
X4
(J)
#4 x 80mm
X6
(L)
Connection Plate
(Left) X2
(R)
Connection Plate
(Right) X2
(M)
Bolt M8 x 30mm
X8
(N)
Bolt M8 x 15mm
X22
(O)
Metal L-Bracket
X6
(P)
#4 x 25mm
X36
Tools Required
Allen Key M4 Allen Key M5 Spanner (Screw driver and Hammer are Not Provided)
Scale Ruler –Use this to measure your screws (mm) ( Actual Ruler Not Provided )
Important –Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
If you have damaged or missing components,
email: [e-mail]

10
Assembly Instructions
If you have damaged or missing components,
email: [e-mail]