Graco 210ES 261830 Operating instructions

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001
- For portable spray application of architectural paints and coatings -
190ES Model: 261825
210ES Model: 261830
Maximum Working Pressure: 3000 psi (20.7 MPa, 207 bar)
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Related Manuals
311988
311979
English
311995
Français
311980
Español
312015
ti9032a
311990 rev.B
Repair
190ES/210ES™
Electric Airless Sprayer

Warning
2311990B
Warning
The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation
point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to
these warnings. Additional, product-specific warnings may be found throughout the body of this manual where appli-
cable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or
cleaning, keep sprayer at least 20 feet (6 m) away from explosive vapors.
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
• Ground equipment and conductive objects in work area. Read Grounding instructions.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
ELECTRIC SHOCK HAZARD
Improper grounding, setup, or usage of the system can cause electric shock.
• Turn off and disconnect power cord before servicing equipment.
• Use only grounded electrical outlets.
• Use only 3-wire extension cords.
• Ensure ground prongs are intact on sprayer and extension cords.
• Do not expose to rain. Store indoors.
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Engage trigger lock when not spraying.
• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.

Warning
311990B 3
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. Read Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. Read Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine Graco
replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your Graco distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or overbend hoses or use hoses to pull equipment.
• Comply with all applicable safety regulations.
• Keep children and animals away from work area.
• Do not operate the equipment when fatigued or under the influence of drugs or alcohol.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1, 1, 1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids
containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical
reaction and equipment rupture, and result in death, serious injury, and property damage.
BURN HAZARD
Equipment surfaces can become very hot during operation. To avoid severe burns, do not touch hot
equipment. Wait until equipment has cooled completely.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDS’s to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eye wear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
•Gloves
• Hearing protection

Component Identification
4311990B
Component Identification
T
J
H
E
A
B
G
F
D
K
M
N
S
PR
U
ti9033a
ti9034a
V
W
X
Ref Component
A Pressure Control
B ON/OFF Switch
DPowerCord
E Fluid Outlet
FPrimeValve
G Kick Stand (210ES)
HPump
J Suction Tube
K Drain Hose
M Fluid Hose
NGun
PTip
RGuard
S Trigger Safety Lock
T Serial Number ID Label
U Filter Cap
V Pail Hook
W Power Flush Adapter
X Shutoff Valve

Installation
311990B 5
Installation
Grounding and Electric
Requirements
The sprayer cord includes a grounding wire with an
appropriate grounding contact.
The sprayer requires:
100-130 Vac, 60 Hz, 11A, 1 phase, circuit with a ground-
ing receptacle.
Never use an outlet that is not grounded or an
adapter.
Do not use the sprayer if the electrical cord has a dam-
aged ground contact. Only use an extension cord with
an undamaged ground contact.
Recommended extension cords:
110-120V: 3-wire, 12 AWG (2.5 mm2) minimum, 300 ft
(90 m) maximum length.
Spray gun: ground through connection to a properly
grounded fluid hose and pump.
Fluid supply container: follow local code.
Solvent and Oil-based fluids: follow local code. Use
only conductive metal pails placed on a grounded sur-
face such as concrete. Do not place the pail on a non-
conductive surface such as paper or cardboard, which
interrupts grounding continuity.
Grounding the metal pail: connect a ground wire to the
pail by clamping one end to pail and other end to ground
such as a water pipe.
To maintain grounding continuity when flushing or
relieving pressure: hold metal part of the spray gun
firmly to the side of a grounded metal pail, then trigger
the gun.
ti9164a
WLD
Smaller gauge or longer extension cords may
reduce sprayer performance.
ti4297
ti9146a

Pressure Relief Procedure
6311990B
Pressure Relief Procedure
Follow this Pressure Relief Procedure whenever you
are instructed to relieve pressure, stop spraying, check or
service equipment or install or clean spray tip.
1. Turn OFF power and turn pressure control to lowest
pressure setting.
2. Hold gun against side of grounded metal flushing
pail. Trigger gun to relieve pressure.
3. Turn prime valve down.
If you suspect the spray tip or hose is clogged or that
pressure has not been fully relieved after following the
steps above, VERY SLOWLY loosen tip guard retaining
nut or hose end coupling to relieve pressure gradually,
then loosen completely. Clear hose or tip obstruction.
4. Engage trigger safety lock on gun if unit is being
shut down or left unattended.
ti8324a
ti9035a
ti8326a

General Repair Information
311990B 7
General Repair Information
• Keep all screws, nuts, washers, gaskets, and electri-
cal fittings removed during repair procedures. These
parts usually are not provided with replacement kits.
• Test repairs after problems are corrected.
• If sprayer does not operate properly, review repair
procedure to verify you did it correctly. See Trouble-
shooting, page 8.
• Overspray may build up in the air passages.
Remove any overspray and residue from air pas-
sages and openings in the enclosures whenever
you service sprayer.
• Do not operate the sprayer without the motor shroud
in place. Replace if damaged. Motor shroud directs
cooling air around motor to prevent overheating and
insulates the control board from accidental electric
shock.
Flammable materials spilled on hot, bare, motor
could cause fire or explosion. To reduce risk of burns,
fire or explosion, do not operate sprayer with cover
removed.
To reduce risk of serious injury, including electric
shock:
• Do not touch moving or electric parts with fingers
or tools while testing repair.
• Unplug sprayer when power is not required for
testing.
• Install all covers, gaskets, screws and washers
before you operate sprayer.
CAUTION
• Do not run sprayer dry for more than 30 seconds.
Doing so could damage pump packings.
• Protect the internal drive parts of this sprayer from
water. Openings in the cover allow for air cooling of
the mechanical parts and electronics inside. If
water gets in these openings, the sprayer could
malfunction or be permanently damaged.
• Prevent pump corrosion and damage from freezing.
Never leave water or water-base paint in sprayer
when its not in use in cold weather. Freezing fluids
can seriously damage sprayer. Store sprayer with
Pump Armor to protect sprayer during storage.

Troubleshooting
8311990B
Troubleshooting
Problem What To Check
(If check is OK, go to next check)
What To Do
(When check is not OK, refer to this column)
Motor Won’t Operate
Basic Fluid Pressure 1. Pressure control knob setting.
Motor will not run if set at mini-
mum (fully counter-clockwise).
Slowly increase pressure setting to see if motor
starts.
2. Spray tip or fluid filter may be
clogged.
Relieve pressure, page 6. Then clear clog or
clean gun filter. Refer to gun instruction manual,
311979.
Basic Mechanical 1. Pump frozen or hardened paint Thaw sprayer if water or water-based paint has
frozen in sprayer. Place sprayer in warm area to
thaw. Do not start sprayer until thawed com-
pletely. If paint hardened (dried) in sprayer,
replace pump packings. See page 12, Dis-
placement Pump Replacement.
2. Displacement pump connecting
rod pin. Pin must be completely
pushed into connecting rod and
retaining spring must be firmly in
groove or pump pin.
Push pin into place and secure with spring
retainer. See page 12, Displacement Pump
Replacement.
3. Motor. Remove drive housing
assembly. See page 14, Drive
Housing Replacement. Try to
rotate fan by hand.
Replace motor if fan won’t turn. See page 26,
Motor Replacement.

Troubleshooting
311990B 9
Basic Electrical
See wiring diagram, page
27
1. Electric supply. ON/OFF switch in
OFF position. Meter must read
100-130 Vac.
Turn ON/OFF switch to ON position. Reset
building circuit breaker, replace building fuses.
Try another outlet.
2. Extension cord. Check extension
cord continuity with volt meter.
Replace extension cord.
3. Sprayer power supply cord.
Inspect for damage such as bro-
ken insulation or wires.
Replace power supply cord. See page 25,
Power Cord Replacement.
4. Fuse. Check replaceable fuse on
control board (next to ON/OFF
switch).
Replace fuse after completing motor inspection.
See page 20, Fuse Replacement.
5. Motor leads are securely fas-
tened and properly connected to
control board.
Replace loose terminals; crimp to leads. Be
sure terminals are firmly connected.
Clean circuit board terminals. Securely recon-
nect leads.
6. Motor thermal switch. Yellow
motor leads must have continuity
through thermal switch.
Replace motor. See page 26, Motor Replace-
ment.
7. Brush cap missing or loose brush
lead connections.
Install brush cap or replace brushes if leads are
damaged. See page 17, Motor Brush
Replacement.
8. Brush length which must be
greater than 1/4 in. (6mm).
NOTE: Brushes do not wear at
the same rate on both sides of
motor. Check both brushes.
Replace brushes. See page 17, Motor Brush
Replacement.
9. Motor armature commutator for
burn spots, gouges and extreme
roughness.
Remove motor and have motor shop resurface
commutator if possible. See page 26, Motor
Replacement.
10. Motor armature for shorts using
armature tester (growler) or per-
form spin test, page 15.
Replace motor. See page 26, Motor Replace-
ment.
11. Pressure control not plugged in
to control board.
Insert pressure control connector into control
board.
Problem What To Check
(If check is OK, go to next check)
What To Do
(When check is not OK, refer to this column)

Troubleshooting
10 311990B
Low Output 1. Worn spray tip. Relieve pressure, page 6. Replace tip. Refer to
gun instruction manual, 311979.
2. Verify pump does not continue to
stroke when gun trigger is
released.
Service pump. See page 12, Displacement
Pump Replacement.
3. Prime valve leaking. Relieve pressure, page 6. Then repair prime
valve. See page 23, Manifold Replacement.
4. Suction tube connections. Tighten any loose connections. Check o-ring on
suction tube.
5. Electric supply with volt meter.
Meter must read 100-130 Vac.
Low voltages reduce sprayer per-
formance.
Reset building circuit breaker; replace building
fuse. Repair electrical outlet or try another
outlet.
6. Extension cord size and length. Replace with a correct, grounded extension
cord. See page 5, Grounding and Electric
Requirements.
7. Leads from motor to circuit board
for damaged or loose wire con-
nectors. Inspect wiring insulation
and terminals for signs of over-
heating.
Be sure male terminal pins are centered and
firmly connected to female terminals. Replace
any loose terminals or damaged wiring.
Securely reconnect terminals.
8. Worn motor brushes which must
be greater than 1/4 in. (6 mm).
Replace brushes. See page 17. Motor Brush
Replacement.
9. Motor brushes binding in brush
holders.
Clean brush holders. Remove carbon dust by
using compressed air to blow out brush dust.
10. Low stall pressure. Turn pressure
control knob fully clockwise. Replace pressure control assembly. See page
21, Pressure Control Assembly Replace-
ment.
11. Motor armature for shorts by
using an armature tester
(growler) or perform spin test,
page 15.
Replace motor. See page 26, Motor
Replacement.
Problem What To Check
(If check is OK, go to next check)
What To Do
(When check is not OK, refer to this column)

Troubleshooting
311990B 11
Motor runs and pump
strokes
1. Prime Valve Open. Close prime valve.
2. Paint supply. Refill and reprime pump.
3. Intake strainer clogged. Remove and clean, then reinstall.
4. Suction tube leaking air. Tighten nut. Check o-ring on tube.
5. Intake valve ball and piston ball
are seating properly.
See Pump Manual 312015. Strain paint before
using to remove particles that could clog pump.
6. Leaking around throat packing
nut which may indicate worn or
damaged packings.
See Pump Manual 312015.
7. Pump rod damaged. See Pump Manual 312015.
Motor runs but pump does
not stroke
1. Displacement pump pin dam-
aged or missing.
Replace pump pin if missing. Be sure retaining
spring is fully in groove all around connecting
rod. See page 12, Displacement Pump
Replacement.
2. Connecting rod assembly for
damage.
Replace connecting rod assembly. See page
12, Displacement Pump Replacement.
3. Gears or drive housing. Inspect drive housing assembly and gears for
damage and replace if necessary. See page 14,
Drive Housing Replacement.
Motor is hot and runs
intermittently
1. Be sure ambient temperature
where sprayer is located is not
more than 115°F (46°C) and
sprayer is not located in direct
sun.
Move sprayer to shaded, cooler area if possible.
2. Motor has burned windings indi-
cated by removing positive (red)
brush and seeing burned adja-
cent commutator bars.
Replace motor. See page 26, Motor
Replacement.
3. Tightness of pump packing nut.
Overtightening tightens packings
on rod, restricts pump action and
damages packings.
Loosen packing nut. Check for leaking around
throat. Replace pump packings if necessary.
See pump manual 312015.
Problem What To Check
(If check is OK, go to next check)
What To Do
(When check is not OK, refer to this column)

Displacement Pump Replacement
12 311990B
Displacement Pump Replacement
See manual 312015 for pump repair instructions.
Removal
1. Relieve pressure , page 6. Unplug sprayer from outlet.
2. Loosen two screws (11) and remove pail hanger (10).
3. Loosen nut (37) and remove suction tube (39).
Loosen nut (B) and remove coupled hose (42).
4. Cycle pump until pin (31) is in position to be
removed.
5. Disconnect power cord from outlet.
6. Push up retaining spring (C). Push out pump pin (31).
7. Loosen pump jam nut (34). Unscrew and remove
pump (33).
11
10
ti9138a
42B
37
39 ti9139a
C
31
ti9040a
34
33
ti9141a

Displacement Pump Replacement
311990B 13
Installation
1. Extend pump piston rod fully. Apply grease to top of
pump rod (D). Install jam nut (34) on pump threads.
2. Install pump rod (D) into connecting rod (30).
3. Install pump pin (31). Verify retainer spring (30a) is
in groove over pump pin.
4. Push pump (33) up until pump threads engage.
5. Screw in pump until threads are flush with top of
drive housing opening.
6. Align pump outlet (E) to back.
7. Screw jam nut (34) up onto pump until nut stops.
Tighten jam nut by hand, then tap 1/8 to 1/4 turn
with a 20 oz (maximum) hammer to approximately
75 ft-lb (102 N•m).
8. Install suction tube (39) and coupled hose (42).
Tighten nuts (37) and (B).
.
9. Fill packing nut with Graco TSL until fluid flows onto
top of seal. Install pail hanger (10 ) with screws (11).
If pump pin works loose, parts could break off due to
force of pumping action. Parts could project through
air and result in serious injury or property damage.
CAUTION
If the pump jam nut loosens during operation, the
threads of the drive housing will be damaged.
D
34
ti9143a
30
30
30a
31
33
ti9144a
ti6111a
ti
E
34
ti9145a
42B
37
39 ti9139a
10
11
ti9040a

Drive Housing Replacement
14 311990B
Drive Housing Replacement
Removal
1. Relieve pressure, page 6.
2. Remove pump (33). Displacement Pump Replace-
ment, page 12.
3. Disconnect power cord from outlet.
4. Remove two screws (11) and cover (32).
5. Remove screw (13) and four screws (4).
6. Pull drive housing (29) out of motor front endbell.
7. Remove gear cluster (27) and (26) and thrust bear-
ing (28) from drive housing.
Installation
1. Apply a liberal coat of grease to gears and needle
bearing surfaces. Install thrust bearing (28) and
gears (26) and (27) in motor front endbell.
2. Push drive housing (29) into motor front endbell.
Insert gear crank (27) through hole in connecting
rod (30).
3. Install four screws (4) and screw (13).
4. Install cover (32) with two screws (11).
5. Install pump (33). Displacement Pump Replace-
ment, page 12.
CAUTION
Do not drop gear cluster (27) and (26) when removing
drive housing (29). Gear cluster may stay engaged in
motor front endbell or drive housing.
13
32
26
11
27
28
4
29
2
ti9148a
Needle
Bearing Surfaces
27
26
28
ti9147a
13
11
ti9149a
32
4
30
27

Spin Test
311990B 15
Spin Test
See Wiring Diagram, page 27.
To check armature, motor winding and brush electrical
continuity:
1. Relieve pressure, page 6. Disconnect power cord
from outlet.
2. Remove kick stand (66) on 210ES.
3. Remove two screws (5) and toolbox (3).
4. Remove two screws (11) and front cover (32).
5. Remove screw (13) and shroud (12).
6. Remove drive housing (29), page 14.
7. Disconnect motor connector (D).
Armature Short Circuit Test
Quickly turn motor fan by hand. If motor coasts two or
three revolutions before complete stop, there are no
electrical shorts. If motor does not spin freely, armature
is shorted. Replace motor, page 26.
Armature, Brushes, and Motor Wiring Open
Circuit Test (Continuity)
1. Connect red and black motor leads with test lead.
Turn motor fan by hand at about two revolutions per
second.
2. If uneven or no resistance, check for missing brush
caps, broken brush springs, brush leads, and worn
brushes. Repair as needed, page 17.
3. If still uneven or no resistance, replace motor, page 26.
4. Connect motor connector (D).
5. Install drive housing, page 14.
6. Install shroud (12) with screw (13).
7. Install front cover (32) with two screws (11).
8. Install toolbox (3) with two screws (5).
9. Install kick stand (66) on 210ES.
11
32
13
29
12
ti9150a
D
ti9135a
D

Fan Replacement
16 311990B
Fan Replacement
Removal
1. Relieve pressure, page 6. Disconnect power cord
from outlet.
2. Remove kick stand (66) on 210ES.
3. Remove two screws (5) and toolbox (3).
4. Remove two screws (11) and front cover (32).
5. Remove screw (13) and shroud (12).
6. Remove retaining ring (57b) on back of motor.
7. Pull off fan (57a).
Installation
1. Slide new fan (57a) on back of motor. Be sure fan
blades face motor.
2. Install spring clip (57b).
3. Install shroud (12) with screw (13).
4. Install front cover (32) with two screws (11).
5. Install toolbox (3) with two screws (5).
6. Install kick stand (66) on 210ES.
57b
57a
11
12
ti9151a
13 32

Motor Brush Replacement
311990B 17
Motor Brush Replacement
See Wiring Diagram, page 27.
Removal
Replace brushes worn to less than 1/4 in. (6 mm).
Brushes wear differently on each side of motor, check
both sides.
1. Relieve pressure, page 6. Disconnect power cord
from outlet.
2. Remove kick stand (66) on 210ES.
3. Remove two screws (5) and toolbox (3).
4. Remove two screws (11) and front cover (32).
5. Remove screw (13) and shroud (12) (see illustration
on page 15).
6. Disconnect motor connector (D) from control board (18).
7. Cut tie wrap (F).
8. Locate two yellow wires (C). Cut each yellow wire at
the center.
9. Pry off two brush caps (A). Remove brushes (B)
from motor.
10. Discard old brush assembly.
11. Rotate fan by hand and blow compressed air into
top brush holder to remove brush dust.
Installation
\
1. Install new brushes (B) in motor with wires facing
toward front of motor. Install positive (red) brush
lead in top of motor and negative (black) brush lead
in side of motor.
2. Push each cap (A) into place over brush. Orient
each cap with the two projections on either side of
the brush lead. You will hear a snap when cap is
securely in place.
3. Strip approximately 1/4 inch (6 mm) of insulation
from end of each yellow wire (C) from motor.
4. Insert stripped end into end of a butt splice (E) on
new brush assembly.
5. Crimp ends of butt splice (E) around each wire. Pull
gently on each wire to be sure wire does not pull out
of butt splice.
6. Wrap new tie wrap around motor and wires only. Trim off
excess. Be sure pressure hose is not caught in tie wrap.
7. Connect motor connector (D) to control board (18).
8. Install shroud (12) with screw (13) (see illustration,
page 15).
9. Install front cover (32) with two screws (11).
10. Install toolbox (3) with two screws (5).
11. Install kick stand (66) on 210ES.
Place end of a shop vacuum hose over lower brush
holder. Turn on shop vacuum when you blow com-
pressed air into top brush holder.
Use all new parts included in brush kit. Do not
reuse old parts if new replacement parts are pro-
vided.
A
B
+
-
C
D
E
F
D
A
Red
Black
B
D
ti9133a

Control Board Replacement
18 311990B
Control Board Replacement
See Wiring Diagram, page 27.
Removal
1. Relieve pressure, page 6. Disconnect power cord
from outlet.
2. Remove kick stand (66) on 210ES.
3. Remove two screws (5) and toolbox (3).
4. Remove two screws (11) and front cover (32).
Remove screw (13) and shroud (12) (see illustra-
tion, page15).
5. Disconnect pressure control assembly connector
(A) from control board (18).
6. Disconnect motor connector (D) from control board (18).
7. Remove three screws (11) securing control board to
housing (two are located on the front and one on the
back next to the power cord).
8. Pull control board out slightly and then slide control
board back and off of frame.
9. Remove grommet and wires from strain relief.
.
10. Remove two power cord (C) connectors from control
board.
120V
ti9132a
18
D
A
11
18
ti9154a
Make sure power cord is free and not wrapped
around cord wrap.
Ground wire remains attached to sprayer with
grounding screw.
ti6122a
18
Grommet
Strain
Relief
120V
C
ti9132a
18

Control Board Replacement
311990B 19
Installation
1. Push grommet and power cord wires into strain
relief in control board (18).
2. Connect power cord connectors to terminals indi-
cated on control board (18).
3. Slide control board into place on side of motor front
endbell.
4. Replace three screws (11). Torque to 30-35 in-lb
(3.4-3.9 N.m).
5. Connect motor connector (D) and pressure control
assembly connector (A).
6. Install shroud (12) with screw (13). Install front cover
(32) with two screws (11). (see illustration, page 15).
7. Install toolbox (3) with two screws (5).
8. Install kick stand (66) on 210ES.
Route power cord (19) between coupled hose (42)
to filter manifold and sprayer frame.
ti6122a
18
Grommet
Strain
Relief
120V
ti9132a
18
C
Bottom View of Sprayer ti9153a
42
19
11
18
ti9154a
120V
ti9132a
18
D
A

Fuse Replacement
20 311990B
Fuse Replacement
If the fuse is blown, check for:
• Pinched or shorted wires
• A defective motor (see Spin Test, page 15)
• A locked or frozen pump
Correct defective condition before replacing fuse.
Removal
1. Relieve pressure, page 6. Disconnect power cord
from outlet.
2. Remove kick stand (66) on 210ES.
3. Remove two screws (5) and toolbox (3).
4. Remove two screws (11) and front cover (32).
Remove screw (13) and shroud (12) (see illustra-
tion, page15).
5. Remove fuse from control board.
Installation
1. Install Fuse 119277 on control board.
2. Install shroud (12) with screw (13). Install front cover
(32) with two screws (11). (see illustration, page 15).
3. Install toolbox (3) with two screws (5).
4. Install kick stand (66) on 210ES.
Replaceable Fuse
ti9134a