Graco 239-139 Operation manual

308–698
Rev. A
7102A
INSTRUCTIONS-PARTS LIST
INSTRUCTIONS
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
239–139 Air Control Conversion Kit
Converts 113–156 Air Control Assembly to
113–896 Air Control Assembly.
150 psi (10 bar) Maximum Air Inlet Pressure
Table of Contents
Installation 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco W arranty and Disclaimers 4. . . . . . . . . . . . . . . . .
Toll-Free Graco Phone Number 4. . . . . . . . . . . . . . . . . .
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
COPYRIGHT 1997, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001

 
Installation
Disassembly
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure in your separate pump
and ram manuals.
1. Relieve the pressure.
2. Disconnect the air assist hose from the swivel el -
bow (A). See Fig. 1.
3. Disconnect the air tube from the tube fitting (B).
Unscrew the tube fitting from the tee (C). Keep the
tube fitting (B) for reassembly .
4.
Remove the tee (C), valve (D), and elbow (A) from
the air control assembly . Discard these parts.
7100A
Fig. 1
A
B
C
D
Installing the 239–139 Conversion Kit
1. Install the tee (1), adapter (2), control valve (3),
and swivel (4) as shown in Fig. 2.
2. Reinstall the tube fitting (B) in the tee (1).
3. Reconnect the air tube to the tube fitting (B).
4. Reconnect the free end of the air assist hose to
the swivel (4).
5. When changing drums, operate the control valve
(3) as explained on page 3.
7101A
Fig. 2
1Not
included in Conversion Kit 239–139.
3
B
1
2
4
1
1
E
Parts List
Ref.
No. Part No. Description Qty.
1 113–914
TEE; 1/4 npt(f) 1
2 113–912
ADAPTER; 1/8 npt x 1/4 npt 1
3 113–913 VALVE, control, air assist 1
4 113–915
SWIVEL; 1/8 npt(m) x1/4 npt(f) 1

 
Operation
Changing Drums
WARNING
MOVING P ARTS HAZARD
Moving parts can pinch or amputate your
fingers. When the pump is operating and
when raising or lowering the ram, keep
your fingers and hands away from the pump intake,
ram plate, and lip of the drum.
After conversion, the ram air controls operate dif ferent-
ly. T
o change a drum, use this procedure instead of the
one given in your ram manual.
1. Stop the pump. Close the pump air bleed valve.
2. Before raising the ram plate, locate the pushbutton
on the control valve (3). See Fig. 2.
3. Set the director valve (E) to UP to raise the ram
plate. At the same time, carefully equalize the
pressure in the drum by operating the air release
valve.
4.
Raise the ram plate until it is completely out of the
drum.
5.
Remove the empty drum.
6. Inspect the ram plate and, if necessary , remove
any remaining material or material build-up.
7. Place a full drum on the ram base.
8. Lower the ram and adjust the position of the drum
relative to the ram plate, as explained in your ram
manual.

4 308-698
Graco W arranty and Limitation of Liability
WARRANTY
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects
in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. Graco will,
for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defec -
tive. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’ s written rec-
ommendations.
This warranty does not cover , and Graco shall not be liable for general wear and tear , or any malfunction, damage or wear
caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident,
tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by
the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the im -
proper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not sup -
plied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor
for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective
parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not
disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the
costs of parts, labor , and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PUR-
POSE.
Graco’
s sole obligation and buyer ’ s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no
other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or prop -
erty
, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two
(2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE IN CONNECTION WITH
ACCESSORIES, EQUIPMENT , MA TERIALS, OR COMPONENTS
SOLD BUT NOT MANUFACTURED BY GRACO.
These items sold, but not manufactured by Graco (such as electric motors,
switches, hose, etc.) are subject to the warranty , if any , of their manufacturer . Graco will provide purchaser with reasonable assis -
tance in making any claim for breach of these warranties.
For Sales to Canadian Customers:
Except as expressly stated herein, Graco makes no representations, warranties or conditions, express, implied or collateral, con -
cerning any goods or services sold, and GRACO SHALL NOT BE LIABLE IN ANY MANNER FOR any other representation,
warranty or condition of any kind, whether arising by operation of law or otherwise, including but not limited to, WARRANTIES OF
MERCHANTABLE QUALITY OR FITNESS FOR A PARTICULAR PURPOSE.
LIMITATION OF LIABILITY
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equip -
ment hereunder , or for the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of
contract, breach of warranty , the negligence of Graco, or otherwise.
Graco Phone Number
TO PLACE AN ORDER , contact your Graco distributor , or call this number to identify the distributor closest to you:
1–800–367–4023 T oll Free
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit, Los Angeles
Foreign Offices: Belgium, Canada, England, Korea, France, Germany , Hong Kong, Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN U.S.A. 308–698 February 1997