Graco SG20 Parts list manual

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001
ti12661a
SG20 Airless Spray Gun with RAC V Tip
Models: 24A448
Maximum Working Pressure: 3600 psi (248 bar, 24.8 MPa)
-For the application of architectural paints and coatings -
The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point
symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings.
Additional, product-specific warnings may be found throughout the body of this manual where applicable.
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured
components will pierce skin. This may look like just a
cut, but it is a serious injury that can result in amputation. Get
immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove,
or rag.
• Do not spray without tip guard and trigger guard
installed.
• Engage trigger lock when not spraying.
•Follow Pressure Relief Procedure in this manual, when
you stop spraying and before cleaning, checking, or ser-
vicing equipment.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes,
in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, ciga-
rettes, portable electric lamps, and plastic drop cloths
(potential static arc).
• Keep work area free of debris, including solvent, rags
and gasoline.
• Do not plug or unplug power cords, or turn power or light
switches on or off when flammable fumes are present.
• Ground all equipment in the work area. See Grounding
instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering
into pail.
• If there is static sparking or you feel a shock, stop oper-
ation immediately. Do not use equipment until you iden-
tify and correct the problem.
• Keep a working fire extinguisher in the work area.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influ-
ence of drugs or alcohol.
• Do not exceed the maximum working pressure or tem-
perature rating of the lowest rated system component.
See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equip-
ment wetted parts. See Technical Data in all equipment
manuals. Read fluid and solvent manufacturer’s warn-
ings. For complete information about your material,
request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or dam-
aged parts immediately with genuine manufacturer’s
replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your
distributor for information.
• Route hoses and cables away from traffic areas, sharp
edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull
equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chlo-
ride, other halogenated hydrocarbon solvents or flu-
ids containing such solvents in pressurized aluminum
equipment. Such use can cause serious chemical reaction
and equipment rupture, and result in death, serious injury,
and property damage.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment
when operating, servicing, or in the operating area of
the equipment to help protect you from serious
injury. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and
solvent manufacturer
•Gloves
• Hearing protection
WARNINGS
313250A
IMPORTANT SAFETY INSTRUCTIONS. Refer to your
sprayer instruction manual for Pressure Relief, priming and
spray instructions. Keep these instructions.
Instructions/Parts
English

2313250A
Pressure Relief Procedure
Follow this Pressure Relief Procedure
whenever instructed to relieve pressure,
stop spraying, check or service equipment,
or install or clean spray tip.
1. Turn OFF power and turn sprayer pressure control to low-
est pressure setting.
2. Hold gun against side of grounded metal flushing pail.
Trigger gun into pail to relieve pressure.
If you suspect spray tip or hose is clogged or that pressure has
not been fully relieved after following the steps above, VERY
SLOWLY loosen tip guard retaining nut or hose end coupling
to relieve pressure gradually, then loosen completely. Clear
hose or tip obstruction.
Gun Trigger Lock (3a)
To prevent injury when the gun is not in use, always
set the gun’s trigger lock (3a) if unit is being shut
down or left unattended.
Setup
Make sure sprayer is turned off and unplugged from power
source. Refer to your sprayer instruction manual for priming
and spray instructions.
Connect Gun to Sprayer
1. Attach supply hose to sprayer fluid outlet.
2. Attach other end of supply hose to gun swivel (5). Use two
wrenches (one on the swivel (5) and one on the hose), to
tighten all connections securely.
3. Refer to sprayer instruction manual for priming
instructions.
Installing Tip (15) and Guard (2) on Gun
1.If equipment has recently been operated,
Relieve Pressure. Set trigger lock (3a).
2. Using a pencil or similar object, insert seat (16) into back
of guard (2).
3. Install guard (2) over end of gun (21). Tighten retaining
nut.
4. Insert tip (15) into slot on guard (2).
Operation
Spraying
1. Unlock trigger lock (3a).
2. Be sure the arrow shaped tip (15) faces forward (spray).
3. Hold gun perpendicular and approximately 12-inches
(304 mm) from surface. Move gun first, then pull gun
trigger (3) to spray a test pattern.
4. Slowly increase pump pressure until coverage is uniform
and even (see sprayer instruction manual for additional
information).
Aligning Spray
1.Relieve Pressure. Set trigger lock (3a).
2. Loosen guard retaining nut.
3. Align guard (2) horizontally to spray a horizontal pattern.
4. Align guard (2) vertically to spray a vertical pattern.
Clearing Clogs
1. Relieve Pressure. Set trigger lock (3a).
2. Rotate tip (15) 180°. Unlock trigger lock (3a). Trigger gun
into pail or onto ground to remove clog.
3. Set trigger lock (3a). Rotate tip (15) 180° back to spray
position.
Cleanup
Flush gun after each work shift and store in a dry location.
Clean handle grip with water or with a rag wetted in mineral
spirits or paint thinner. Do not soak.
WARNING
WARNING
WARNING
Trigger Locked
(no spray)
Tr i g g e r U n l o cke d
(spray)
ti8908a ti8909a
WARNING
WARNING
WARNING
CAUTION
Never soak gun in solvents. Do not leave the gun or
any parts in water.

313250A 3
Parts
▲Replacement Danger and Warning labels, tags, and
cards are available at no cost.
✓Keep these spare parts on hand to reduce downtime.
ti8904b
9
13
21
33
32
7
6
5
22
24
4
3
11
1
23
8
12
2
15a
15
3a
10
Ref
No. Part. No. Description Qty
1 SEAT, valve 1
2✓237859 GUARD, RAC IV 1
3 243639 TRIGGER, kit, 4 finger, assy, includes
32 and 33 (model 255108)
1
288816 TRIGGER, kit, 2 finger, assy, includes
32 and 33 (model 255109)
1
3a LOCK, trigger, included with 3 1
4 195495 GUARD, trigger 1
5 238817 SWIVEL, gun 1
6✓288749 FILTER, gun; latex, 50 mesh 1
288750 FILTER, gun, latex, 100 mesh 1
7✓179733 SEAL, sleeve 1
8 195395 CAP, end 1
9 115483 NUT, lock 1
10 115484 PIN, actuator 2
11 195419 HOUSING, needle 1
12 156766 GASKET 1
13 NEEEDLE, gun 1
15✓286515 TIP, spray, RAC V 1
15a 243004 RAC V, gasket and seal kit, (includes 2
rubber gaskets and 2 metal seals)
1
21 195389 HOUSING, fluid (sand blasted) 1
195390 HOUSING, fluid (tumbled) 1
22 113409 RETAINER, guard 1
23 15J775 HANDLE, grip (model 255108) 1
15J776 HANDLE, grip (model 255109) 1
24 115485 PACKING, o-ring 1
32 177538 STUD, trigger 1
33 105334 NUT, lock, hex 1
34 288817 KIT, repair, gun, includes 1, 9, 12, 13 1
Ref
No. Part. No. Description Qty

For complete warranty information contact your local Graco distributor, call Graco customer
service: 1-800-690-2894 or visit our website: www.graco.com.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 313250
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
07/2008
Maintenance
Before performing any maintenance on gun, read all warnings
on front cover of this manual and Relieve Pressure.
Cleaning/Replacing Filter (6)
1. Relieve Pressure. Set trigger lock (3a).
2. Disconnect fluid hose from gun at swivel (5).
3. Disconnect trigger guard (4) from guard retainer (22).
4. Unscrew handle (23) from gun (21).
5. Remove filter (6) through top of handle (23).
6. Clean filter (6). Use a soft brush to loosen and remove
excess debris.
7. Insert clean filter (6) into handle (7).
8. Reattach handle (7) to gun (21). Tighten securely.
9. (Model 255109 only) If finger guard is not aligned, apply
torque manually, rotating the grip until it is aligned with the
trigger.
10. Reconnect trigger guard (4) to guard retainer (22).
Replacing Needle
1. Relieve Pressure. Set trigger lock (3a).
2. Remove tip (15) and guard (2) from gun (21).
3. Disconnect fluid hose from gun at swivel (5).
4. Release trigger lock (3a). Squeeze trigger (3) while
unscrewing diffuser (18) from front of gun (1).
5. Remove locknut (9) and end cap (8).
6. Tap needle assembly (13) out, with the needle exiting
through front of gun (1).
7. Use a soft brush to clean out internal passages of gun.
8. Grease o-rings of new needle using a non-silicon grease.
9. Guide new needle (13) through front of gun (21).
10. Loosely install end cap (8) and locknut (9).
11. Again, grease o-rings of new needle using a non-silicon
grease.
12. Grease threads of diffuser/seat (1). Place gasket (12) on
diffuser/seat (1).
13. Squeeze trigger (3) while installing gasket (12) and
diffuser (1). Torque
14. Hold gun with nozzle facing up.
15. Turn locknut (9) clockwise until you see and feel trigger (3)
raise slightly.
16. Turn locknut (9) 3/4 turn counter-clockwise.
NOTE: When needle is properly adjusted, trigger will move
freely.
17. Connect fluid hose. Install tip (15) and guard (2).
18. Prime sprayer. See sprayer instruction manual.
19. Trigger gun into bucket until fluid flows from gun.
20. Release trigger (3). Fluid flow should stop immediately.
21. Set triger lock (3a).
22. Aim gun into bucket. Trigger gun. No fluid show flow.
23. If the gun fails tests , steps 20 and/or 22, Relieve
Pressure and disconnect hose. Readjust needle. Repeat
tests.
WARNING
ti9211a