Graco T-MAX 506 Use and care manual

3A6748B
EN
Operation, Repair, Parts
T-Max™506/657/6912
Texture Sprayer
For portable spraying of water-based materials. Can be used for application of
solvent-based materials only when solvent compatible seals are installed and
solvent compatible, conductive hoses are used. For professional use only.
Not approved for use in European explosive atmosphere locations.
T-Max 506: 50 bar (5 MPa, 725 psi) Maximum Working Pressure
T-Max 657: 65 bar (6.5 MPa, 940 psi) Maximum Working Pressure
T-Max 6912: 69 bar (6.9 MPa, 1000 psi) Maximum Working Pressure
See page 4-6 for model information.
Important Safety Instructions
Read all warnings and instructions in this manual and related manuals before using
the equipment. Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
Related Manuals
STX Trigger Gun 3A6746 Bag Roller Kits 312790, 3A4995
T-Max Remote Switch Kit 3A6784 T-Max Applicator 312879
PrimeValve Accessory Kit 3A6785 Free Flow Applicator 313537
Vibra-Flo T-Max 3A6909 Inline Applicator 309495
Air Manifold Kit 3A6839
www.graco.com/techsupport
?? ??

23A6748B
Contents
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Component Identification 506 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Component Identification 657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Component Identification 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Pump Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
T-Max 506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
T-Max 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Solvent-Based Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Amp Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Extension Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Mixing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Hose Lubrication Mixing Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Start Up - Airless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Spray Tip Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Clear Spray Tip Clog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Start Up - Air Assist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Start Up - Air Assist STX Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Control Board Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Control Board Removal 506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Control Board Installation 506, 657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Control Board Removal 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Control Board Installation 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Pump Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Pump Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Pump Repair 506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Pump Repair 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Cross-Section Reference / Pump Ball Identification 6912 . . . . . . . . . . . 63
Motor Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Motor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Recycling and Disposal at End of Life . . . . . . . . . . . . . . . . . . . . . . . . . . 66

3A6748B 3
Parts - Hopper Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Parts List - Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Parts - Power Module 506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Parts List - Power Module 506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Parts - Power Module 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Parts List - Power Module 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Parts - Pump 289555 (506) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Parts List - Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Parts - Pump 289556 (657) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Parts List - Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Parts - Pump 25E668 (6912) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Parts List - Pump 25E668 (6912) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Parts - Control Box 506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Parts List - Control Box 506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Parts - Control Box 6912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Parts List - Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
506/657 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6912 - US . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6912 - UK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
CALIFORNIA PROPOSITION 65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Models
43A6748B
Models
T-MAX 506
Model Hoses Applicator 17 Gallon
Hopper
Power
Cord VAC
17Z169 Bare Unit
CEE 7/7 230VAC
17X980 3m whip
5m T-Max Applicator 
17Z170 Bare Unit
UK 110VAC
17X982 3m whip
5m T-Max Applicator 
17Z291 Bare Unit
Multi-Cord 230VAC
17X981 3m whip
5m T-Max Applicator 
T-MAX 657
Model Hoses Applicator 17 Gallon
Hopper
Power
Cord VAC
17Z171 Bare Unit
CEE 7/7 230VAC
17X983 3m whip
5m T-Max Applicator 
17Z172 Bare Unit
UK 110VAC
17X985 3m whip
5m T-Max Applicator 
17Z292 Bare Unit
Multi-Cord 230VAC
17X984 3m whip
5m T-Max Applicator 

Models
3A6748B 5
T-MAX 6912
Model Hoses Applicator 25 Gallon
Hopper
Air
Manifold
Power
Cord VAC
17Z173 Bare Unit
CEE 7/7 230VAC
17Z626
3m whip
5m
10m

17X986
3m whip
5m
10m
T-Max
Applicator 
17Z532
3m whip
5m
10m
Inline
Applicator 
17X990
3m whip
5m
10m
Free-Flow
Applicator 
17X993
3m whip
5m
10m
STX
Spray Gun 
17Z285
3m whip
5m
10m
T-Max
Applicator
Free-Flow
Applicator

17Z288
3m whip
5m
10m
T-Max
Applicator
STX
Spray Gun

17Z529
3m whip
5m
10m
T-Max
Applicator
Pole
Applicator

17Z174 Bare Unit
UK 110VAC
17Z629
3m whip
5m
10m

17X988
3m whip
5m
10m
T-Max
Applicator 
17Z534
3m whip
5m
10m
Inline
Applicator 
17X992
3m whip
5m
10m
Free-Flow
Applicator 
17Z282
3m whip
5m
10m
STX
Spray Gun 
17Z287
3m whip
5m
10m
T-Max
Applicator
Free-Flow
Applicator

17Z290
3m whip
5m
10m
T-Max
Applicator
STX
Spray Gun

17Z531
3m whip
5m
10m
T-Max
Applicator
Pole
Applicator


Models
63A6748B
T-MAX 6912 continued
Model Hoses Applicator 25 Gallon
Hopper
Air
Manifold
Power
Cord VAC
17Z293 Bare Unit
Multi-Cord 230VAC
17Z628
3m whip
5m
10m

17X987
3m whip
5m
10m
T-Max
Applicator 
17Z533
3m whip
5m
10m
Inline
Applicator 
17X991
3m whip
5m
10m
Free-Flow
Applicator 
17X994
3m whip
5m
10m
STX Spray
Gun 
17Z286
3m whip
5m
10m
T-Max
Applicator
Free-Flow
Applicator

17Z289
3m whip
5m
10m
T-Max
Applicator
STX SPray
Gun

17Z530
3m whip
5m
10m
T-Max
Applicator
Pole
Applicator

17Z175 Bare Unit
NA 120VAC
17Z630 
17X989 50’
9’ whip
T-Max
Applicator 
17Z283 50’
9’ whip
STX Spray
Gun 
17Z284 100’
9’ whip
STX Spray
Gun 
17Z703 100’
9’ whip
STX Spray
Gun 

Warnings
3A6748B 7
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this
equipment. The exclamation point symbol alerts you to a general warning and the hazard
symbols refer to procedure-specific risks. When these symbols appear in the body of this
manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols
and warnings not covered in this section may appear throughout the body of this manual
where applicable.
WARNING
GROUNDING
This product must be grounded. In the event of an electrical short circuit, grounding
reduces the risk of electric shock by providing an escape wire for the electric current.
This product is equipped with a cord having a grounding wire with an appropriate
grounding plug. The plug must be plugged into an outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
•Improper installation of the grounding plug is able to result in a risk of electric
shock.
•When repair or replacement of the cord or plug is required, do not connect the
grounding wire to either flat blade terminal.
•The wire with insulation having an outer surface that is green with or without
yellow stripes is the grounding wire.
•Check with a qualified electrician or serviceman when the grounding instructions
are not completely understood, or when in doubt as to whether the product is
properly grounded.
•Do not modify the plug provided; if it does not fit the outlet, have the proper outlet
installed by a qualified electrician.
•This product is for use on a nominal 110V or 230V circuit and has a grounding
plug similar to the plugs illustrated in the figure below.
•Only connect the product to an outlet having the same configuration as the plug.
•Do not use an adapter with this product.
Extension Cords:
•Use only a 3-wire extension cord that has a grounding plug and a grounding
receptacle that accepts the plug on the product.
•Make sure your extension cord is not damaged. If an extension cord is necessary
use 12 AWG (2.5mm) minimum to carry the current that the product draws.
•An undersized cord results in a drop in line voltage and loss of power and
overheating.
ti24583a
230V
110V UK 120V

Warnings
83A6748B
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and material fumes, in work area can ignite or
explode. To help prevent fire and explosion:
•Do not spray flammable or combustible materials near an open flame or sources
of ignition such as cigarettes, motors, and electrical equipment.
•Material or solvent flowing through the equipment is able to result in static
electricity. Static electricity creates a risk of fire or explosion in the presence of
material or solvent fumes. All parts of the spray system, including the pump, hose
assembly, spray gun, and objects in and around the spray area shall be properly
grounded to protect against static discharge and sparks. Use Graco conductive
or grounded high-pressure airless material sprayer hoses.
•Verify that all containers and collection systems are grounded to prevent static
discharge. Do not use pail liners unless they are anti-static or conductive.
•Connect to a grounded outlet and use grounded extensions cords. Do not use
a 3-to-2 adapter.
•Do not use a material or a solvent containing halogenated hydrocarbons.
•Do not spray flammable or combustible liquids in a confined area.
•Keep spray area well-ventilated. Keep a good supply of fresh air moving through
the area.
•Sprayer generates sparks. Keep pump assembly in a well ventilated area a least
20 feet (6.1 m) from the spray area when spraying, flushing, cleaning, or
servicing. Do not spray pump assembly.
•Do not smoke in the spray area or spray where sparks or flame is present.
•Do not operate light switches, engines, or similar spark producing products in the
spray area.
•Keep area clean and free of material or solvent containers, rags, and other
flammable materials.
•Know the contents of the materials and solvents being sprayed. Read all Safety
Data Sheets (SDSs) and container labels provided with the materials and
solvents. Follow the material and solvents manufacturer’s safety instructions.
•Keep a working fire extinguisher in the work area.
ELECTRIC SHOCK HAZARD
This equipment must be grounded.Improper grounding, setup, or usage of the
system can cause electric shock.
•Turn off and disconnect power cord before servicing equipment.
•Connect only to grounded electrical outlets.
•Use only 3-wire extension cords.
•Ensure ground prongs are intact on power and extension cords.
•Do not expose to rain. Store indoors.
•Wait five minutes after disconnecting power cord before servicing.

Warnings
3A6748B 9
WARNING
SKIN INJECTION HAZARD
High-pressure spray is able to inject toxins into the body and cause serious injury
that can result in amputation. In the event that injection occurs, get immediate
surgical treatment.
•Do not aim the gun at, or spray any person or animal.
•Keep hands and other body parts away from the discharge. For example, do not
try to stop leaks with any part of the body.
•Always use the spray tip guard. Do not spray without spray tip guard in place.
•Use Graco spray tips.
•Use caution when cleaning and changing spray tips. In the case where the spray
tip clogs while spraying, follow the Pressure Relief Procedure for turning off the
unit and relieving the pressure before removing the spray tip to clean.
•Equipment maintains pressure after power is shut off. Do not leave the
equipment energized or under pressure while unattended. Follow the Pressure
Relief Procedure when the equipment is unattended or not in use, and before
servicing, cleaning, or removing parts.
•Check hoses and parts for signs of damage. Replace any damaged hoses or
parts.
•This system is capable of producing 1000 psi (69 bar, 6.9 MPa). Use Graco parts
or accessories that are rated a minimum of 1000 psi (69 bar, 6.9 MPa).
•Verify that all connections are secure before operating the unit.
•Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with
the controls.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can
cause serious chemical reaction and equipment rupture. Failure to follow this
warning can result in death, serious injury, or property damage.
•Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated
hydrocarbon solvents or fluids containing such solvents.
•Do not use chlorine bleach.
•Many other fluids may contain chemicals that can react with aluminum. Contact
your material supplier for compatibility.

Warnings
10 3A6748B
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•Do not operate the unit when fatigued or under the influence of drugs or alcohol.
•Do not exceed the maximum working pressure or temperature rating of the
lowest rated system component. See Technical Specifications in all
equipment manuals.
•Use fluids and solvents that are compatible with equipment wetted parts. See
Technical Specifications in all equipment manuals. Read fluid and solvent
manufacturer’s warnings. For complete information about your material, request
Safety Data Sheets (SDSs) from distributor or retailer.
•Do not leave the work area while equipment is energized or under pressure.
•Turn off all equipment and follow the Pressure Relief Procedure when
equipment is not in use.
•Check equipment daily. Repair or replace worn or damaged parts immediately
with genuine manufacturer’s replacement parts only.
•Do not alter or modify equipment. Alterations or modifications may void agency
approvals and create safety hazards.
•Make sure all equipment is rated and approved for the environment in which you
are using it.
•Use equipment only for its intended purpose. Call your distributor for information.
•Route hoses and cables away from traffic areas, sharp edges, moving parts, and
hot surfaces.
•Do not kink or over bend hoses or use hoses to pull equipment.
•Keep children and animals away from work area.
•Comply with all applicable safety regulations.
MOVING PARTS HAZARD
Moving parts can pinch, cut, or amputate fingers and other body parts.
•Keep clear of moving parts.
•Do not operate equipment with protective guards or covers removed.
•Equipment can start without warning. Before checking, moving, or servicing
equipment, follow the Pressure Relief Procedure and disconnect all power
sources.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent
serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns.
This protective equipment includes but is not limited to:
•Protective eyewear, and hearing protection.
•Respirators, protective clothing, and gloves as recommended by the fluid and
solvent manufacturer.

Component Identification 506
3A6748B 11
Component Identification 506
NOTE: All hoses sent with the unit are for
water-based material application only.
* See page14 for all applicators.
1 Pump Module
2 Hopper Frame
3Pump
4 Pump Outlet
5 Pressure Relief Valve
6 Module Securing Clamp
7 Power Cord
8 ON/OFF Switch
9 Display
10 Pressure Control Knob
11 Locking Pin
12 Hopper Plug
13 Scraper Tool
14 Whip Hose
15 Material Hose
16 T-Max Applicator
17 Inline Applicator
18 Tool Box

Component Identification 657
12 3A6748B
Component Identification 657
NOTE: All hoses sent with the unit are for
water-based material application only.
* See page14 for all applicators.
1 Pump Module
2 Hopper Frame
3Pump
4 Pump Outlet
5 Pressure Relief Valve
6 Module Securing Clamp
7 Power Cord
8 ON/OFF Switch
9 Display
10 Pressure Control Knob
11 Locking Pins
12 Hopper Plug
13 Scraper Tool
14 Whip Hose
15 Material Hose
16 T-Max Applicator
17 Inline Gun
18 Tool Box

Component Identification 6912
3A6748B 13
Component Identification 6912
NOTE: All hoses sent with the unit are for
water-based material application only.
* See page14 for all applicators.
1 Pump Module
2 Hopper Frame
3Pump
4 Pump Outlet
5 Pressure Relief Valve
6 Module Securing Clamp
7 Power Cord
8 Pump Mode Switch
9 ON/OFF Switch
10 Amp Switch
11 Display
12 Pressure Control Knob
13 Locking Pins
14 Hopper Plug
15 Signal / Air Hose
16 Scraper Tool
17 Material Hose
18 Whip Hose
19 Tool Box
20 Free Flow Applicator
21 STX Spray Gun

Component Identification
14 3A6748B
Component Identification
Free Flow
Applicator (17Z128)
T-Max Applicator
(17Z054)
STX Spray Gun
(17Y910)
18m Remote
Switch (17Z157)
30m Remote
Switch (17Z158)
13m Signal/Air
Hose (17Z144)
18m Signal/Air
Hose (17Z148)
33m Signal/Air
Hose (17Z151)
Inline Applicator
(17Y907)

Pump Control Settings
3A6748B 15
Pump Control Settings
T-Max 506/657
Flow Mode (first half of Pressure Control
Knob):
The motor will run continuously at the
speed determined by the Pressure Control
Knob (K). 0-100%
Pressure Mode (second half of Pressure
Control Knob):
The motor will run to meet the
pressure determined by the Pressure Control
Knob (K).
T-Max 6912 Operation
The motor power switch (S) must be
ON for the sprayer to pump material.
K
Pump Control
Setting Description
Pressure
Mode
The motor will run to meet the
pressure determined by the
Pressure Control Knob (K).
Flow Mode
with Remote
Control
The “Flow Mode with Remote
Control” setting allows the
user to control ON/OFF
functionality of the pump
through the remote toggle
switch or the STX Spray
Gun. When the remote toggle
switch or the STX Spray Gun
is installed and the pump
control settings are set to
“Flow Mode with Remote
Control”, they can be used to
turn the pump ON and OFF.
Flow Mode
The motor will run
continuously at the speed
determined by the Pressure
Control Knob (K). 0-100%
S

Preparation
16 3A6748B
Preparation
Grounding
This product is equipped with a cord having
a grounding wire with an appropriate
grounding plug. The plug must be plugged
into an outlet that is properly installed and
grounded in accordance with all local codes
and ordinances.
Do not modify the plug provided; if it does not
fit the outlet, have the proper outlet installed
by a qualified electrician.
Solvent-Based Materials
NOTE: All hoses sent with the unit are for
water-based material application only.
Solvent compatible hoses and applicators
must be used.
Flush the Equipment
•Flush before changing materials, before
fluid can dry or cure in the equipment, at
the end of the day, before storing, and
before repairing equipment.
•Flush with a fluid that is compatible with
the fluid being dispensed and the
equipment wetted parts.
•Flush at the lowest pressure possible.
Check connectors for leaks and tighten
as necessary.
1. Follow Pressure Relief Procedure,
page 19.
2. Set pump to lowest possible fluid
pressure, and start pump.
3. Hold a metal part of the gun firmly to a
grounded metal pail. Trigger the gun
until clean solvent dispenses.
Amp Switch
Select 15A or 20A depending on your circuit
rating. 110V units require 100-120 VAC,
50/60 Hz, 15 – 20A, 1 phase
Select 10A or 16A depending on your circuit
rating. 230V units require 220-240 VAC,
50/60 Hz, 10 – 16A, 1 phase
The equipment must be grounded to
reduce the risk of static sparking and
electric shock. An electric or static spark
can cause fumes to ignite or explode. An
improper ground can cause electric shock.
A good ground provides an escape wire for
the electric current.
To avoid fire and explosion, always
ground equipment and waste container.
To avoid static sparking and injury from
splashing, always flush at the lowest
possible pressure.

Preparation
3A6748B 17
Extension Cords
Use an extension cord with an undamaged
ground contact. If an extension cord is
necessary, use a 3-wire, 12 AWG (2.5 mm2)
minimum.
NOTE: Lighter gauge or longer extension
cords may reduce sprayer performance.
Mixing Material
NOTE: Correct material mixture is essential.
The pump and spray gun will not operate if
the mixture is too thick. Use water-based
materials only.
1. Mix the material and water in a
separate container.
Dry Mix
Carefully mix texture material and water
according to manufacturer instructions
on bag.
Premix
Slowly add water to a 5 gallon (18.9 liter)
bucket of premix.
2. Agitate to mix with mixing paddle, to a
smooth, lump-free consistency.
3. Make certain all dry powder clumps are
mixed throughly before pouring mixture
into the sprayer hopper.
ti2496c
40 lb.
TEXTURE MIX
5 GAL
NOTICE
Failure to make certain that all dry powder
is throughly mixed may cause tip or pump
clogging.
PREMIX
5
GAL
ti2493b
ti30766a

Preparation
18 3A6748B
Hose Lubrication Mixing Instructions
Hose lubrication (17Z224) is used to lube the
pump and hose passages to reduce the risk
of packout when priming aggregate material.
NOTE: If using other hose lubricants, follow
manufacturer’s mixing instructions.
1. Empty one bag of hose lubricant into
five-gallon bucket and half fill with water.
2. Stir for one minute.
3. Fill remainder of bucket with water. Stir
for one minute.
4. Let mix stand for at least five minutes or
until a slick-like texture develops.

Preparation
3A6748B 19
Pressure Relief Procedure
Follow the Pressure Relief
Procedure whenever you see this
symbol.
1. Turn ON/OFF Switch to OFF and turn
Pressure Control Knob fully
counterclockwise to OFF.
2. Point applicator into hopper. Turn
applicator ON.
This equipment stays pressurized until
pressure is manually relieved. To help
prevent serious injury from pressurized
fluid, such as skin injection, splashing fluid
and moving parts, follow the Pressure
Relief Procedure when you stop spraying
and before cleaning, checking, or
servicing the equipment.

Preparation
20 3A6748B
3. If you suspect the spray tip or hose is
clogged or that pressure has not been
fully relieved:
a. If installed, turn prime valve down to
prime position.
b. VERY SLOWLY loosen the
retaining ring, hose end coupling, or
pressure relief valve to relieve
pressure gradually.
c. Loosen the retaining nut or the
coupling completely.
d. Clear the obstruction in the hose or
tip.
NOTE: If pressure relief valve was used to
relieve pressure, be sure to disassemble and
clean thoroughly.