Graco 244766 Operation manual

Instructions -- Parts List

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440- 1441

Water Sandblaster Kit

- For suction fed injection of sand into the water stream

for abrasive cleaning -

Model 244766

5500 psi (39 MPa, 385 bar) Maximum Working Pressure

Gun and wand not included.

308544D

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

5500 psi (39 MPa, 385 bar) Maximum Working Pressure

Gun and wand not included.

Parts

2 308544

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

WARNING

FUEL HAZARD

The fuel used in this pressure washer is combustible. When spilled on a hot surface it can ignite and

cause a fire.

Do not fill fuel tank while engine is running or hot.

EXHAUST HAZARD

The engine exhaust contains poisonous carbon monoxide, which is colorless and odorless.

Do not operate this equipment in a closed building.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

DDo not alter or modify this equipment. Use only genuine Graco parts and accessories.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum working pressure of the lowest-rated system component. See

Technical Data for the maximum working pressure of this equipment.

DUse fluids and solvents that are compatible with the equipment wetted parts. See the Technical

Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

DFollow pressure relief before cleaning, checking or servicing this equipment.

DWear ear and eye protection when you operate this equipment.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,

inhaled, or swallowed.

DKnow the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.

DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,

state, and national guidelines.

DAlways wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and

solvent manufacturer.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum wo

for the maximum working pressure of this equipment.

Do not fill fuel tank while engine is running or hot.

The engine exhaust contains poisonous carbon monoxide, which is colorless and odorless.

Do not operate this equipment in a closed building.

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

rking pressure of the lowes

for the maximum working pressure of this equipment.

Use fluids and solvents that are compatible with the equipment wetted parts. See the

section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

before cleaning, checking or servicing this equipment.

Wear ear and eye protection when you operate this equipment.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

t-rated system

for the maximum working pressure of this equipment.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

rking pressure of the lowes

t-rated system

for the maximum working pressure of this equipment.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum wo

rking pressure of the lowes

for the maximum working pressure of this equipment.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum wo

for the maximum working pressure of this equipment.

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,

Wear ear and eye protection when you operate this equipment.

before cleaning, checking or servicing this equipment.

Wear ear and eye protection when you operate this equipment.

section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

before cleaning, checking or servicing this equipment.

Use fluids and solvents that are compatible with the equipment wetted parts. See the

section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

before cleaning, checking or servicing this equipment.

Use fluids and solvents that are compatible with the equipment wetted parts. See the

section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Use fluids and solvents that are compatible with the equipment wetted parts. See the

section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

3308544

WARNING

INJECTION HAZARD

Spray from the gun, leaks, or ruptured components can inject fluid into your body and cause extremely

serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also

cause serious injury.

DFluid injected into the skin is a serious injury. The injury might look like just a cut, but it is a serious

injury. Get immediate surgical treatment.

DDo not point the gun at anyone or at any part of the body.

DDo not put your hand or fingers over the spray tip.

DDo not stop or deflect leaks with your hand, body, glove or rag.

DDo not “blow back” fluid; this is not an air spray system.

DFollow the Pressure Relief Procedure if the spray tip clogs and before you clean, check, or

service this equipment.

DTighten all fluid connections before you operate this equipment.

DEngage gun safety whenever you stop spraying.

DCheck the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not

repair high-pressure couplings; you must replace the entire hose.

Tighten all fluid connections before you operate this equipment.

Engage gun safety whenever you stop spraying.

Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not

repair high-pressure couplings; you must replace the entire hose.

4 308544

Installation

WARNING

Pressure Relief Procedure

To reduce the risk of serious bodily injury, including

fluid injection and splashing in the eyes or on the skin,

always follow this procedure whenever you stop

spraying for more than 10 minutes, when shutting

down, and before checking or repairing any part of

the system.

1. Engage the trigger safety latch.

2. Turn the sprayer off.

3. Remove the ignition cable from the spark plug,

disconnect the air or disconnect the electricity.

4. Shut off the water supply.

5. Disengage the trigger safety latch and trigger the

gun to relieve pressure, and then engage the

trigger safety latch again.

NOTE: Check the spray tip application chart (308514)

to order the proper spray tip for your model of

pressure washer.

Refer to the Parts Drawing on page 7 for the

numbers in parentheses in the text.

1. Remove the tip and male quick coupler from the gun

assembly. Keep these parts for reinstallation on the

gun after sandblasting.

2. Assemble the spray tip (not supplied with kit), to the

tip adapter (4) and male quick coupler (5). Use pipe

sealant on all threads. Connect the assembly to the

female quick coupler on the gun.

3. Assemble the mixer housing (2) to the adapter (4).

Be sure that the sand inlet is located at the top of the

mixing head. See the Parts Drawing.

4. Attach the sand hose (10) to the mixing head.

5. Attach the other end of the sand hose to the sand

probe (1).

to order the proper spray tip for your model of

Refer to the Parts Drawing on page 7 for the

numbers in parentheses in the text.

5. Disengage the trigger safety latch and trigger the

gun to relieve pressure, and then engage the

Check the spray tip application chart (308514)

to order the proper spray tip for your model of

Refer to the Parts Drawing on page 7 for the

numbers in parentheses in the text.

to order the proper spray tip for your model of

Refer to the Parts Drawing on page 7 for the

numbers in parentheses in the text.

5308544

Operation

WARNING

To reduce the risk of injury, always protect eyes

and face with goggles and mask, and hands and

arms with heavy work gloves when spraying abra-

sive materials.

Place the sand induction probe in the sand supply

container.

To Sandblast

1. Connect and open the water supply line before

starting the pressure washer.

2. Trigger the gun to relieve air in the equipment.

3. Start the pressure washer. See its instruction

manual.

4. Trigger the gun to activate the spray.

CAUTION

Always test spray on a scrap of similar material first!

The high pressure spray could damage the surface if

the sandblaster is held too close. See Step 5, below.

5. To check the distance you will need to hold the spray

nozzle from the surface, start to spray at the scrap of

material from a distance of several feet.

Gradually move closer, checking frequently to see if

the high pressure spray is damaging the surface.

6. See the APPLICATION on page 5 for the type of

sand recommended for your work surface.

Always point the sand nozzle downward when not

spraying. This prevents water from entering the sand

supply. If water does get into the sand supply hose,

remove the probe from the sand, hold the gun trigger

open, and let the hose air dry. Always be sure the sand

hose is dry before using.

Keep the sand covered to prevent the overspray from

wetting the sand.

Do not allow small pieces of the sand bag to fall into the

sand supply. A small paper piece could prevent the flow

of sand.

NOTE: To extend the life of the tungsten carbide sand

nozzle (3) rotate the nozzle 45_after every 15

minutes of use.

Sand Saver Operation (Optional)

The spring--loaded collar on the Sand--Saver rotates to

give four different rates of sand injection. From setting

number 1, (maximum sand injection) to setting number 4,

(minimum sand injection).

By experimenting with the different settings on your

Sand--Saver during sandblasting you can determine

which setting is the most economical for the job. See the

table below for approximate sand usage per minute at

each setting.

Setting

Number

Hole

Diameter

Sand Injection Rate

Pounds/Minute*

1None 14

23/16” 7

31/4” 4.2

45/16” 3.6

* Sand injection was calibrated using standard 20’ length

of sand hose. Added length to sand hose will decrease

sand usage.

Shutdown

After the sandblasting operation is complete, remove the

probe from the sand, trigger the gun to clear the hose and

probe of sand. Then, remove the hose from the mixing

head and rinse with water to remove all the sand before

storage.

Before using the gun for other applications, be sure to

reinstall the tip and male quick coupler.

Always test spray on a scrap of similar material first!

The high pressure spray could damage the surface if

the sandblaster is held too close. See Step 5, below.

5. To check the distance you will need to hold the spray

nozzle from the surface, start to spray at the scrap of

2. Trigger the gun to relieve air in the equipment.

3. Start the pressure washer. See its instruction

4. Trigger the gun to activate the spray.

CAUTION

Always test spray on a scrap of similar material first!

The high pressure spray could damage the surface if

* Sand injection was calibrated using standard 20’ length

of sand hose. Added length to sand hose will decrease

sand usage.

5. To check the distance you will need to hold the spray

nozzle from the surface, start to spray at the scrap of

material from a distance of several feet.

move closer, checking frequently to see if

the high pressure spray is damaging the surface.

ATION on page 5 for the type of

sand recommended for your work surface.

Always point the sand nozzle downward when not

Before using the gun for other applications, be sure to

reinstall the tip and male quick coupler.

After the sandblasting operation is complete, remove the

probe from the sand, trigger the gun to clear the hose and

probe of sand. Then, remove the hose from the mixing

head and rinse with water to remove all the sand before

Shutdown

After the sandblasting operation is complete, remove the

probe from the sand, trigger the gun to clear the hose and

probe of sand. Then, remove the hose from the mixing

head and rinse with water to remove all the sand before

storage.

Always test spray on a scrap of similar material first!

The high pressure spray could damage the surface if

the sandblaster is held too close. See Step 5, below.

5. To check the distance you will need to hold the spray

nozzle from the surface, start to spray at the scrap of

Always test spray on a scrap of similar material first!

The high pressure spray could damage the surface if

the sandblaster is held too close. See Step 5, below.

5. To check the distance you will need to hold the spray

nozzle from the surface, start to spray at the scrap of

spraying. This prevents water from entering the sand

supply. If water does get into the sand supply hose,

reinstall the tip and male quick coupler.

Before using the gun for other applications, be sure to

reinstall the tip and male quick coupler.

Before using the gun for other applications, be sure to

reinstall the tip and male quick coupler.

Before using the gun for other applications, be sure to

6 308544

Application

Sand Mesh

Sand mesh refers to the size of sieve through which a

particular grade of sand will pass. A “16/50” mesh means

that normally, most of these particles will pass through a

No. 16 sieve and a very small percentage will pass

through a No. 50 sieve.

NOTE A No. 16 sieve is a mesh that has 16, 0.046 sq.

in. (1.19 mm) openings per inch.

Round Sand

This refers to the round edge of the grain of sand. River

sand is a good example of sand worn to its size by water.

Angular Sand

This refers to grains of sand which have

triangular--shaped edges. Crushed rock or sand is

usually of this type.

Blasting Angle and Distance

The blasting angle can affect the nozzle distance. Always

maintain the recommended blasting angle and the

proper distance from your work surface for the best

sandblasting performance. See below.

BLASTING

ANGLE 30

�

NOZZLE

�

DISTANCE AT 0˚

DISTANCE

AT 30�

NOZZLE

DISTANCE AT

30�

NOZZLE

DISTANCE AT 0�

Removal Of:

Sand

Mesh

Sand

Type

Blasting

Angle

Paint from Metal 20/40 Round

Silica

0 -- 3 0 _

Paint from Masonry 20/40 Round

Silica

0 -- 2 0 _

Rubber Base Paint from

Masonry

10/35 Angular 0 -- 1 5 _

Paint from Wood (Coarse,

Rough Cut Effect)

40/60 Round 1 -- 1 0 _

Paint from Wood

(Smoother, Driftwood

Effect)

20/40 Round 1 -- 1 0 _

Metal Scale 20/40 Round 0 -- 1 5 _

Rust 16/50 Angular 0 -- 2 5 _

The blasting angle can affect the nozzle distance. Always

maintain the recommended blasting angle and the

proper distance from your work surface for the best

sandblasting performance. See below.

Paint from Metal

Paint from Masonry

Rubber Base Paint from

Masonry

Rust

Paint from Wood (Coarse,

Rough Cut Effect)

Paint from Wood

(Smoother, Driftwood

Effect)

Metal Scale

16/50

20/40

7308544

Troubleshooting

Problem Probable Cause Solution

No sand. Plugged sand probe.

Plugged gun.

Wet sand.

Low vacuum.

Clear obstruction and make sure air vents in sand probe

are open.

Remove mixing nozzle and inspect mixing chamber.

Dry or replace sand.

Valve open; air leaks in system. Tighten hose clamps.

Not enough

sand.

Incorrect water nozzle.

Collapsed hose.

Partial obstruction to sand probe.

Low sand level.

Low water pressure and/or flowrate.

Change to 15_spray angle.

Replace hose or remove restriction.

Clear rocks or paper from sand probe inlet.

Change probe to new bag of sand.

See Troubleshooting Chart in pressure washer instruction

manual.

Low water pressure and/or flowrate.

Change probe to new bag of sand.

See Troubleshooting Chart in pressure washer instruction

manual.

8 308544

Parts

Model 244766

3 6 2 4 5

SPRAY TIP — SEE

NOTE

NOTE: A spray tip is not included with the water sandblaster kit. The proper tip must be ordered separately.

REF PART

NO. NO. DESCRIPTION QTY

1 801114 PROBE, Sand 1

2 801115 HOUSING, Mixing head 1

3 801116 NOZZLE, Sand 1

4 801117 ADAPTER, Tip 1

5 801091 COUPLER,Male quick

disconnect 1

6 801120 GASKET 1

7 801121 BARB, Hose, 3/4 npt x 3/4 ID 1

800031 SAND SAVER, (Optional) 1

8 801122 THUMBSCREW 1

9 103927 CLAMP, Hose 2

10 801124 HOSE, Sand, 20 ft. 1

Wetted Parts: Aluminum, Stainless Steel, Tungsten

Carbide, Zinc Plated Carbon Steel,

Polyvinyl Chloride, Buna--N.

A spray tip is not included with the water sandblaster kit. The proper tip must be ordered separately.

NO. NO. DESCRIPTION QTY

1 801114 PROBE, Sand 1

SPRAY TIP — SEE

NOTE

2 801115 HOUSING, Mixing head 1

3 801116 NOZZLE, Sand 1

4 801117 ADAPTER, Tip 1

disconnect 1

6 801120 GASKET 1

7 801121 BARB, Hose, 3/4 npt x 3/4 ID 1

800031 SAND SAVER, (Optional) 1

A spray tip is not included with the water sandblaster kit. The proper tip must be ordered separately.

Wetted Parts: Aluminum, Stainless Steel, Tungsten

Carbide, Zinc Plated Carbon Steel,

Polyvinyl Chloride, Buna--N.

A spray tip is not included with the water sandblaster kit. The proper tip must be ordered separately.

Wetted Parts: Aluminum, Stainless Steel, Tungsten

Carbide, Zinc Plated Carbon Steel,

A spray tip is not included with the water sandblaster kit. The proper tip must be ordered separately.

NO. NO. DESCRIPTION QTY

1 801114 PROBE, Sand 1

A spray tip is not included with the water sandblaster kit. The proper tip must be ordered separately.

NO. NO. DESCRIPTION QTY

1 801114 PROBE, Sand 1

Polyvinyl Chloride, Buna--N.

Carbide, Zinc Plated Carbon Steel,

Polyvinyl Chloride, Buna--N.

9308544

Notes

10 308544

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from

defects in material and workmanship on the date of sale to the original purchaser for use. With the exception ofany special, extended,

or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the

equipment determined by Graco to be defective. This warranty applies only when the equipment is installed,operated and maintained

in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by

faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or

substitution of non--Graco component parts. Nor shall Graco be liable for malfunction, damage or wearcaused by the incompatibility of

Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,

installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for

verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The

equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect

in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and

transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT

NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other

remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any

other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the

date of sale.

Graco MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT

NOT MANUFACTURED BY Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.),

are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim

for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

breach of warranty, the negligence of Graco, or otherwise.

FOR Graco BRAZILIAN/CANADIAN/COLUMBIAN CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings

entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English.

TO PLACE AN ORDER OR FOR SERVICE, contact your Graco distributor,

or call 1--800--690--2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

MM 308544

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

www.graco.com

PRINTED IN USA 308544D 5/1991 Rev. 5/2005

Graco MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORI

NOT MANUFACTURED BY Graco

are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim

for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT

NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other

remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any

other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the

Graco MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORI

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

breach of warranty, the negligence of Graco, or otherwise.

FOR Graco BRAZILIAN/CANADIAN/COLUMBIAN CUST

OMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings

entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English.

TO PLACE AN ORDER OR FOR SERVICE

to identify the nearest distributor.

Graco MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

ES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT

. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.),

are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

Graco MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

ES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT

. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.),

are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

Graco MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORI

. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.),

are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

Graco MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORI

NOT MANUFACTURED BY Graco

. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.),

are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim

for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

to identify the nearest distributor.

, contact your Graco distributor,