Granberg BASELIFT 6300 User manual

2021-06-02
User manual Baselift
Products
Height adjustable frames for worktops
BASELIFT 6300 / 6310
BASELIFT CORNER 6301 / 6311
BASELIFT CORNER 6302 / 6312
BASELIFT CORNER 6303 / 6313
Height Adjustable Modular Worktops
Mini kitchen module Granberg ESF
Combi Kitchen module Granberg ES11S4
Combi Kitchen module Granberg ES20S4
Combi Kitchen module Granberg ES30S4
Combi Kitchen module Granberg ESHS4
Hob module Granberg S4
Mini kitchen module Granberg ES11S2
Mini kitchen module Granberg ESFS
Sink Module Granberg ES11
Sink Module Granberg ES20
Sink Module Granberg ES30
Sink module Granberg ESG
Sink module Granberg ESH
Workbench module Granberg CT
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se

Content
1. Introduction
2. Declaration of conformity with EU directives
3. Intended use
4. Technical data
5. Safe use
6. Safety arrangements
7. Load distribution and side forces
8. Actions after use
9. Instructions for recycling
10. Spare parts list
11. Electric system / Electric diagram
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se

1. Introduction
We have the pleasure to deliver a Granberg Interior worktop lift, an electrically operated lifting and lowering
system. The Worktop lift unit can be used separately, or together with the Granberg Wall cabinet lifts, and it
becomes then a total adaptation of the kitchen. The lift is suitable for kitchens of various makes, which are made
according the standards EN 1116 and EN 1153.
Only authorized persons may use the Worktop lift unit!
Authorization means obligation to read and follow the instructions.
It is very important that you read and understands the instructions before you use the device.
If you have any questions - contact your supplier.
This Instruction manual shall be available for all concerned persons, be kept in a protected place and shall follow
the product, if it is moved to another installation site or another house or apartment owner.
Correct use, operation, inspections and maintenance are decisive for efficient and safe work.
2. Declaration of conformity with EU directives
This product is CE-marked and is thereby declared to conform to the basic functionality and safety requirements of
current Machinery, EMC and Low Voltage Directives.
“EG Declaration of Conformity” is found in a separate document.
3. Intended use
The worktop lift is intended to vertically lift and lower the worktop to achieve a convenient location performing
normal kitchen work. The operation shall be indoors, under normal housing conditions regarding temperature,
humidity and lighting. Electric hob, a sink and drawers can be incorporated.
The worktop lift unit is not intended for use in moist environments.
It is assumed that the work top benches and the cabinets are made according the standards EN 1116 and EN 1153.
Countertop on adjacent cabinets must not protrude over its cabinet frame. Protrusion of the countertop to adjacent
cabinets constitute a risk of crushing and will not be accepted!
Any use other than the above is subject to approval by Granberg and definition of the current allowable working
conditions. Contact Granberg to planned change approved!
Solid wood benches are not recommended.
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se

4. Technical data
Wall-mounted 6300HA / 6300LA,
6301HA / 6301LA, 6302HA / 6302LA, 6303HA / 6303LA
Floor-mounted 6310HA / 6310LA,
6311HA / 6311LA, 6312HA / 6312LA, 6313HA / 6313LA
Front height, 40 mm 6300LA / 6310LA,
6301LA / 6311LA, 6301LA / 6312LA, 6303LA / 6313LA
Front height, 103 mm 6300HA / 6310HA,
6301HA / 6311HA, 6301HA / 6312HA, 6303HA / 6313HA
Frame depth from wall 560 - 590 mm
Depth top-board (15 mm shallower than top-boards
on fixed cabinets)
565-630 mm
Height adjustment 300 mm
Speed level 30 mm / Sek.
Electrical connection Plug for 230 V
Power consumption Max 5A, 1150W
Corner models: Max 10A, 2300W
Max no. of full work cycles per hour 5
Safety The safety strip is placed under the front edge of the
worktop.
If anything touches the safety strip, the lifting unit stops
Lifting force 100 kg
IP-class IP 20
Space to wall / adjoining cabinet 5 mm
Space to wall (for tiles) 15 mm
Tiling From 700 mm above floor (alternatively all the way
down to the floor)
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se

5. Safe use
The Worktop lift unit is provided with safety arrangements in order to prevent and avoid damages and accidents. It
is however still very important that the operator is well instructed in how to install and operate the Worktop lift
unit. In the following the Worktop lift unit means the lifting machine and the fitted accessories, such as drawers,
sink and hob.
Only use the Worktop lift unit for its intended purpose.
The operation and use must be made in such way that there is no risk for damages on persons and property.
The Worktop lift unit may only be operated by persons who have read and understood these instructions,
and are authorized to use it.
Be aware of that you as an operator are responsible for that nobody is damaged.The Worktop lift unit and
the work area must be in proper condition. The Worktop lift unit must not be used if any fault has appeared
which influences the functions or the operation safety. It shall also not be used if it has been repaired,
altered or adjusted without permission of a responsible person.
Do not touch any part of the lift when operating it. Only press the button for desired motion direction.
Do not put hands, arms, or any other part of the body or any object under the worktop or the cabinets when
it is operated.
Do not operate with drawn out drawers.
Do not raise the Worktop lift unit unless the space above it is free from persons or obstacles. In particular if
the Worktop lift unit is installed under a Wall cabinet lift with adjustable height there is an imminent risk
that you do not notice objects or equipment that might be trapped.
Notice the jamming risk between the Worktop lift units and adjacent worktops and cabinets.
Only stable and securely loaded items may be handled. Mind the tilting risk for objects on the worktop,
which are unstable, e.g. carelessly piled.
Safety devices must not be taken out of service or removed.
Alterations of the Worktop lift unit that influence the operational safety or the functions are not allowed.
Do not overload the Worktop lift unit and make sure that the load distribution is correct.
It is absolutely forbidden for persons to stay on the worktop, to stand on extended drawers or to use the lift
for lifting persons.
Always distribute the load uniformly on the worktop, to avoid cantilevered loading. Consider the risk that the
load can roll, slide or fall over.
Use safe and sufficient lifting methods when handling load to and from the Worktop lift unit. In particular
beware when handling heavy items, and goods with hazardous content or with sharp corners and edges.
Be aware of the risks when you work on Worktop lift unit. The risks are depending on the arrangements on
the worktop.
The Worktop lift unit shall regularly, once a year, be inspected in order to prevent accidents.
Applicable Building and Safe use Regulations must be complied with.
Do not use the Worktop lift unit as a lifting jack, e.g. for lifting things from the floor.
Do not use the Worktop lift unit in a potentially explosive environment.
When the operation is in a public location, particularly when children can enter the work area, the operator
shall make satisfactory arrangements to prevent persons from entering the hazardous area when the lift is
being operated, or it has been lowered from the parking position, e.g. by means of blocking the work area or
by means of adding protection devices.
Decals and markings must not be removed or made illegible.
During inspections, service and repair work there shall be no load on the worktop or in the cabinets. The
most common functions can be reached when the cover panels have been removed.
Competent persons only must carry out installation, service and repair works.
Only Granberg original spare parts shall be used when replacing any parts. Our warranty commitment can
otherwise be invalidated.
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se

6. Safety arrangements
The underside of the Worktop lift unit
is provided with a security strip. If the
security strip is pressed during
lowering, the worktop lift unit shall
stop immediately.
Check the security strip function
often.
7. Load distribution and side forces
Note that the max. rated load means that the load is distributed over and inside the entire Worktop Lift.
Point loads are not allowed.
It is absolutely forbidden for persons to stay on the worktop, to stand on extended drawers or to use the lift for
lifting persons.
Basic loading requirements:
100 % of the rated load distributed over the entire cabinet volume.
Horizontal forces are not allowed.
Horizontal forces can appear, for example, when pressing onto the shelves or the load.
It is difficult to estimate the size of the actual horizontal force, so utmost care must always be taken.
Further to the incorporated safety arrangements additional safety actions may be required on or at the Worktop lift
unit. Discuss suitable actions with your Granberg representative or with the health and safety inspection.
We recommend that a Risk assessment in accordance with the Machinery Directive shall be made for the actual
working conditions. If the owner fits accessories, contact Granberg to get approval for the loading conditions.
Maximum load: 100 kg
Top board and all other equipment must be included in the maximum load.
Note that the max. rated load means that the load is distributed over and inside the entire Worktop Lift. Point
loads are not allowed.
8. Actions after use
The Worktop lift unit shall after use be left in its current position.
Switch off the main switch and lock it in closed position, if unauthorized use can occur.
To prevent unauthorized use can it is also possible to furnish the control panel with a key switch, by means of which
the control circuit is disconnected.
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se

9. Instructions for recycling
When the Worktop lift shall be re-used it must be cleaned, inspected and go through a full operation test before it is
installed on the new site.
We recommend the machine to be sent to Granberg or to the Granberg distributor to get this done.
The machine is manufactured from re-usable materials or from materials that can be recycled.
10. Spare parts list
If any component does not work or has broken, contact your supplier. Only Granberg original spare parts must be
used when replacing any parts. Our warranty commitment may otherwise be invalidated.
Return of spare parts:
Contact Granberg prior to any return of parts.
Do not return any parts that have been worn out during normal operation or accidentally damaged. Only return worn
or
damaged parts if it is considered that the fault is covered by our warranty conditions. In such cases, return the parts
without delay, otherwise the right to replacement may be lost.
When ordering spare parts always quote the manufacturing number and type.
Motors Control box Key for safety lock
Safety strip Control button, Aluminium
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se

11. Electric system / Electric diagram
Powered by TCPDF (www.tcpdf.org)
Granberg Interior AB - Box 6112 - 600 06 Norrköping - SWEDEN
Tel: [phone] - E-mail: [email protected] - Internet: www.granberg.se