Granberg Butler 720 User manual

Butler 722
Butler 720

Content
Section: Headline: Page:
1. Introduction................................................................................................................................................ 3
2. Declaration of Conformity
................................................................................................................... 3
3. Intended use - Technical data.............................................................................................................. 3
Operator’s information:
4.1 Operate......................................................................................................................................................... 4
4.2 Safe use......................................................................................................................................................... 4
4.3 Load distribution and side forces ....................................................................................................... 5
4.4 Actions after use
......................................................................................................................................... 5
4.5 Cleaning
...................................................................................................................................................... 6
4.6 Maintenance
.............................................................................................................................................. 6
5. Instructions for Recycling
........................................................................................................................ 6
6. Decals
............................................................................................................................................................. 7
7. Warranty
....................................................................................................................................................... 7
8. Service & maintenance records
............................................................................................................ 7
9. Faultfinding................................................................................................................................................. 8
10. Functional test........................................................................................................................................... 8
11. Spare parts list............................................................................................................................................ 9
12. CE-declaration of Conformity
................................................................................................................ 10

3. Intended use - Technical data
The Wardrobe lift Butler is intended to vertically lift and lower clothes on the clothes-rail to and from the wardrobe. The opera-
tion shall be indoors under normal housing conditions regarding temperature, humidity and lighting.
The Wardrobe lift must not be used in humid rooms.
Model: 720-06062 720-10062 722-06062 722-10062
Cabinet width, inside 545 - 868 mm 945 - 1568 mm 545 - 868 mm 945 - 1568 mm
Cabinet height, inside Adjusted for the length
of the clothes
Adjusted for the length
of the clothes
Adjusted for the length
of the clothes
Adjusted for the length
of the clothes
Cabinet depth, inside Adjusted for the clothes Adjusted for the clothes Adjusted for the clothes Adjusted for the clothes
Vertical stroke, max 704 mm 704 mm 1118 mm 1118 mm
Horizontal stroke, max 614 mm 614 mm 626 mm 626 mm
Machine height, vertical arm 695 mm 695 mm 710 mm 710 mm
Machine height, lowered arm 854 mm 854 mm 675 mm 675 mm
Time for a lift or lowering stroke, approx 15 sec. 15 sec. 24 sek. 24 sek.
Mains supply 100-240VAC, 50/60Hz,
2.0A
100-240VAC, 50/60Hz,
2.0A
100-240VAC,
50/60Hz, 2.0A
100-240VAC,
50/60Hz, 2.0A
El. protection class IP 20 IP 20 IP 20 IP 20
Max no. of full work cycles per hour 6 6 6 6
Weight 12 kg 12 kg 14 kg 14 kg
Max load on the clothes-rail 30 kg 30 kg 30 kg 30 kg
The noise pressure is less than 70 db(A) 70 db(A) 52 db(A) 52 db(A)
Technical data, Wardrobe lift Butler:
1. Introduction
We have the pleasure to deliver a Granberg Interior Wardrobe lift Butler, an electrically operated lifting and lowering
system for installation in new or existing wardrobes.
The Wardrobe lift has got a clothes-rail, where clothes can be hung. With the push button box the motorized clothes-rail is
lowered to a convenient height for handling the clothes.
The lift has adjustable width and there are two models.
Only authorized persons may use the Wardrobe lift!
Authorization means obligation to read and follow the instructions.
It is very important that you read and understands the instructions before you use the device.
If you have any questions - contact your supplier.
This Instruction manual shall be available for all concerned persons, be kept in a protected place and shall follow the product,
if it is moved to another installation site or another house or apartment owner.
Correct use, operation, inspections and maintenance are
decisive for ecient and safe work.
2. Declaration of Conformity with EU-directives
This product is CE-marked and is granted to conform to the basic safety and operation requirements, in accordance with de
actual Machinery, EMC- and Low voltage Directives. A separate “CE-Declaration of Conformity” is available in
section 12.

4.2 Safe use
The Wardrobe lift is provided with safety arrangements in order to prevent and avoid damages and accidents. It is however still
very important that the operator is well instructed in how to install and operate the Wardrobe lift.
 
 
 
authorized to use it.
 
 
appeared which influences the functions or the operation safety. It shall also not be used if it has been repaired,
altered or adjusted without permission of a responsible person.
 
enough for the total weight. Competent persons shall carry out the installation work.
 
the time when operations are taking place.
 
 
brought from the parking position. The parking position means when the Wardrobe lift is fully raised and brought to
the wall, i.e. at the top level.
 
 
the open door.
 
 
 Only stabile and securely loaded items may be handled. Hangers must be suitable for the clothes, and in good condition.
 
 
 
 
 
when handling heavy items, and clothes with dangerous content or sharp parts, such as needles.
 
 
 
 
 
 
make satisfactory arrangements to prevent persons from entering the hazardous area when the lift is being operated,
or it has been lowered from the parking position, e.g. by means of blocking the work area or by means of adding
protection devices.
 
 
 
be invalidated.
4.1 Operate
UP
STOP
DOWN
Remote
Control
Corded
handcontrol

Installationssteg
03721
WEIGHT:
A3
SHEET 1 OF 1 SCALE:1:8
DWG NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
MATERIAL:
DEBUR AND BREAK SHARP EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS TOLERANCES: LINEAR: SS-ISO 2768-m ANGULAR: SS-ISO 2768-m
DRAWN
Granberg Interior AB
Tel. [phone]
Fax. [phone]
[email protected]
www.granberg.se
Joel
2014-11-26
CHECKED
4.3 Load distribution and side forces
Note that the max. rated load 30 kg means that the load is distributed over the clothes-rail.
Point loads are not allowed.
Basic loading requirements:
* The load is distributed aver the entire clothes rail.
* Horizontal forces are not allowed.
Horizontal forces can appear, for example, when pressing onto the Wardrobe lift or the load.
It is dicult to estimate the size of the actual horizontal force, so utmost care must always be taken.
Further to the incorporated safety arrangements additional can safety actions may be required on or at the Wardrobe lift.
Discuss suitable actions with your Granberg representative or with the health and safety inspection.
We recommend that a Risk assessment in accordance with the Machinery Directive shall be made for the actual
working conditions.
4.4 Actions after use
The Wardrobe lift shall after use be left fully raised to the top level, the parking position.
Switch off the main switch or take out the electric plug if unauthorized use can occur. To prevent unauthorized use it can also
is possible top lace the push button box inside a lockable cabinet.

4.5 Cleaning
In its use in a house the mechanism can be exposed to dirt. As the Wardrobe lift contains electrical components it is very
important that cleaning is made according this instruction.
WARNING!
* The Wardrobe lift must absolutely not be connected to the electric supply when cleaning is carried out.
* The Wardrobe lift must absolutely not be rinsed with water!
Care instructions:
The Wardrobe lift is cleaned with lukewarm water and a non-scratching detergent containing soap or similar. Use a Wettex
swab or similar. After cleaning the surfaces shall be dried to avoid lime deposits.
Scratching detergents or tools e.g. steel wool may not be used.
The wardrobe shall be cleaned and maintained in accordance with the manufacturers’ instructions.
4.6 Maintenance
The Wardrobe lift is maintenance-free. Greasing and other actions are made during the manufacturing for the lifetime of the
lift. From safety point of view however some components shall be inspected each year.
* Inspections, service and repair work shall be made by competent persons.
* Remove the objects from the Wardrobe lift before maintenance and repair works are made.
1. Run the lift down and up all the way to resp. end position. Check that it runs freely without trapping risks and jarring
sounds. Check that it stops and stays in the lower resp. upper positions.
2. Check that the cables are not chafed, squeezed or breaking.
3. Check that the attachments are in proper order.
Accomplished inspections and repair works shall be specied in the service records in section 8.
5. Instructions for recycling
When the Wardrobe lift shall be re-used shall it must be cleaned, inspected and go through a full operation test before it is
installed on the new site.
We recommend the machine to be sent to Granberg or to the Granberg distributor to get this done.
The machine is manufactured from re-usable materials or from materials that can be recycled.

30
6. Decals
Two decals are included in the instruction manual envelope, and these must be placed in the wardrobe.
The Max. load decal shall be
placed at the handheld control.
The decal that explains that the
wardrobe is specially equipped shall be
placed close to the handheld control.
7. Warranty
In accordance with the warranty conditions Orgalime S 2000 the manufacturer will replace or repair all faults which depend on
manufacturing or material faults and which appear within twenty-four (24) months from the delivery. For further details about
the conditions, see Orgalime S 2000.
Note! Alternative warranty conditions may apply. See the Order Acknowledgement for actual conditions.
The warranty is only valid if inspections and maintenance is carried out in accordance with the instructions. This warranty does
not cover the cost of normal maintenance, settings or scheduled adjustments as specied in the instructions. Also the labour
costs for such actions are not covered by the warranty.
Damages caused by misuse or incorrect operation of the equipment means that the warranty would expire.
Before any warranty work is commenced by a customer Granberg must be contacted for analysis and approval. We do not ac-
cept to carry any warranty costs if the repair work has started without an agreement by us.
Do not return any parts that have been worn out during normal operation or accidentally damaged. Only return worn or dam-
aged parts if it is considered that the fault is covered by our warranty conditions. In such cases, return the parts without delay,
otherwise the right to replacement may be lost.
When returning parts always quote the details shown on the manufacturer’s plate, i.e.
Type, manufacturing number, year
and describe the operating conditions for the machine.
Remember to quote name, address and telephone number for the appropriate contact person.
8. Service and Maintenance Records
Service & maintenance
Date:______________________
Sign._______________________
Remarks:___________________
___________________________
___________________________
___________________________
Service & maintenance
Date:______________________
Sign._______________________
Remarks:___________________
___________________________
___________________________
___________________________
Service & maintenance
Date:______________________
Sign._______________________
Remarks:___________________
___________________________
___________________________
___________________________

9. Fault nding
The Wardrobe lift is designed and tested to achieve optimum operation reliability and long life, provided that the operation,
maintenance and inspections are carried out in accordance with the prescribed instructions. If in spite of this a fault appears
you can get guidance about what to do according to the faultfinding list below.
Remove the clothes from the rail before fault finding and repair work is carried out.
Fault finding, service and repair work shall made by competent persons only.
If any problem remains after you have taken actions in accordance with the list below you must contact a competent
technician or you supplier.
10. Functional test
When repair work has been carried out on the Wardrobe lift a complete functional test with full load shall be made:
Run the Wardrobe lift down and up all the way to respectively end position. Check that it moves freely, without hindrance and
jarring sounds. Check that no cables are jammed.
Symptom Action
The machine does not move when a control signal
is given. Check that the installation is done correctly according to the installation instructions. Carefully check
the left and right motor unit is connected to the appropriate plug on the control unit.
Check that there is voltage to the control unit. A blue light on the control unit illuminates when power
is applied.
Check the batteries in the remote control. Battery: 1 x CR2032
(Not USA/Canada which has corded hand control)
Disconnect power to the control unit in 30 sec. and reconnect.
If none of the above works, contact your supplier.
Clothes rail stops when driving upwards Check the maximum load. The clothes rail will stop to protect the motor if the clothes rail has more
than the allowable load (30 kg).
Clothes rail can not run down but slowly upward. There have been interruptions in the power supply to the control unit. Run the clothes rail all the way
up to the top until it stops by itself. Now, the device is reset and can be used again.

20
02095
WEIGHT:
A3
SHEET 1 OF 1 SCALE:1:5
DWG NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
MATERIAL:
DEBUR AND BREAK SHARP EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS TOLERANCES: LINEAR: SS-ISO 2768-m ANGULAR: SS-ISO 2768-m
DRAWN
Granberg Interior AB
Tel. [phone]
Fax. [phone]
[email protected]
www.granberg.se
Andreas
2014-02-04
CHECKED
A B
11. Spare parts list
If any component does not work or has broken, contact your supplier. Only Granberg original spare parts must be used when
replacing any parts. Our warranty commitment may otherwise be invalidated.
Return of spare parts:
Contact Granberg prior to any return of parts.
Do not return any parts that have been worn out during normal operation or accidentally damaged. Only return worn or dam-
aged parts if it is considered that the fault is covered by our warranty conditions. In such cases, return the parts without delay,
otherwise the right to replacement may be lost.
When ordering spare parts always quote the manufacturing number and type.
A - Lift mechanism, left
B - Lift mechanism, right
C - Control unit
D - Handheld control unit
E - Power cable
F - Motor cable
Okin nätkabel
WEIGHT:
A3
SHEET 1 OF 1 SCALE:1:5
DWG NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
MATERIAL:
DEBUR AND BREAK SHARP EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS TOLERANCES: LINEAR: SS-ISO 2768-m ANGULAR: SS-ISO 2768-m
DRAWN
Granberg Interior AB
Tel. [phone]
Fax. [phone]
[email protected]
www.granberg.se
Joel
2013-12-19
CHECKED
CD
EF

12. CE-Declaration of conformity
(According Machinery Directive 2006/42/EG, Annexe 2A)
Manufacturer: Granberg Interior AB Tel. [phone]
Box 6112,
SE-600 06 NORRKÖPING, Sweden
declares under sole responsibility that the
product:
to which this declaration relates, is in manufactured in conformity with the following harmonised documents,
following the provisions of Machinery Directive 2006/42/EG, the Low Voltage Directive 2014/35/EU and the EMC Directive
2014/30/EU.
It also conforms to the following harmonised standards:
EN 60204-1:2006 Safety of Machinery - Electrical Equipment of Machines -General Requirements
EN ISO 13857:2008 Safety distances to prevent hazard zones being reached by upper and lower limbs
EN 349:1993+A1:2008 Safety of machinery. Minimum gaps to avoid crushing of parts of the human body
The undersigned is authorized to assemble the technical documentation.
Norrköping, 2017-06-19
Tobias Granberg, VD
Managing Director
Space for machine plate