Grandinroad Corinne 3707A User manual

grandinroad®
EMAIL
[email protected]
CONTACT 1.800.491.4958
for assembly questions on
Weekdays // 8am-8pm EST
Saturday // 9am-6:30pm EST
WARNING: Failure to follow these directions and
warnings can result in serious injury and/or product damage.
If any parts become missing, damaged or worn, discontinue use until
they are replaced with identical parts.
Never stand on or use this chair as a ladder.
!
Do not tip this chair when seated.
!
!
This item is intended for indoor use only.
!
#3707A
Corinne Arm Chair
Assembly Instructions
Item #175755

TOOLS
PARTS
Please confirm you have the necessary parts to complete the assembly.
1
1.800.491.4958
ALLEN
WRENCH
Chair Seat (x1)
HARDWARECOMPONENTS
ALong Bolt with Washers (x8) E
Front Legs (x2)
B
Right Back Leg (x1)
C
Left Back Leg (x1)
D

2
ASSEMBLE
Corinne Arm Chair
Chair Seat (x1)
A
Right Rear Leg (x1)
C
Long Bolt w/
Washers (x2)
E
HELP?
1.800.491.4958
FASTEN the Right Back Leg (C) in the
leg slot as shown below using two Long
Bolts with Washers (E) and an allen wrench.
NOTE: Do Not Over-tighten Bolts.
With assistance, FLIP the Chair Seat (A) upside down and rest it on a
table.
1
2
A
C
ALLEN WRENCH
E
2
x

3
ASSEMBLE
Corinne Arm Chair
4
3
Front Leg (x1)
B
Left Back Leg (x1)
D
HELP?
1.800.491.4958
CHAIR
ASSEMBLY
Long Bolt w/
Washers (x4)
E
FASTEN the Left Back Leg (D) in the leg
slot as shown below using two Long Bolts
with Washers (E) and an allen wrench.
NOTE: Do Not Over-tighten Bolts.
FASTEN the Front Leg (B) in the leg slot
as shown below using two Long Bolts with
Washers (E) and an allen wrench.
NOTE: Do Not Over-tighten Bolts.
D
B
E
2
x
E
2
x
ALLEN WRENCH

HELP?
1.800.491.4958
4
ASSEMBLE
Corinne Arm Chair
With assistance, FLIP the Chair upright and move to the desired
location.
6
5
Front Leg (x1)
B
CHAIR
ASSEMBLY
Long Bolt w/
Washers (x2)
E
FASTEN the Front Leg (B) in the leg slot
as shown below using two Long Bolts with
Washers (E) and an allen wrench.
NOTE: Do Not Over-tighten Bolts.
B
E
2
x
ALLEN WRENCH

5
ASSEMBLE
Corinne Arm Chair
CHAIR
ASSEMBLY
Please contact one of our Product Specialist for assembly assistance questions or questions at
1-800-491-4958. Specialist are available weekdays 8:00 AM to 8:00 PM EST or Saturdays 9:30
AM to 6:00 PM.
LEVELING
THE HOLES IN THE SEAT FRAME HAVE BEEN OVERSIZED TO ALLOW FOR EASIER ASSEMBLY.
If your chair is not sitting level, adjustment may be necessary.
To adjust, slightly loosen the bolts that connect the LEGS to the SEAT FRAME, until the parts can move
freely.
Next, set the chair upright (in its intended location) and apply pressure on the seat frame until all legs
touch the ground.
Re-tighten the bolts while keeping the parts in this configuration.
7
It may also be necessary, as a final adjustment,
to raise or lower leg height to eliminate wobble.
Rotate the adjustable foot glides on the legs right
to lower leg height. Rotate left to raise leg height.
LOWER
RAISE