GRAUPNER Kingpad mc-edition mc-28 Owner's manual

EN
Copyright © Graupner/SJ GmbH
Programming manual
Part 2
mc-26 / mc-28 / mc-28 4D
MC-28
MC-28
MC-28 MC-28
esc set
No. S1036 / 33028 / S1033
16 channel HoTT 2,4 GHz transmitter

3 / 80
33028_mc_28_Teil2_jh
Index
Introduction............................................................................. 7
Service Centre................................................................................7
Use and menu functions......................................................... 8
Short-Cuts ......................................................................................8
Definition of terms.................................................................. 9
Receiver configuration .......................................................... 10
Fixed-wing models .......................................................................10
Helicopter models.......................................................................11
Vehicles, boats .............................................................................11
Copter ..........................................................................................12
Receiver power supply.................................................................12
Symbols explication .............................................................. 13
Menus description ................................................................ 13
Meaning of the warnings...................................................... 13
Model selection..................................................................... 14
Copy/Delete........................................................................... 15
Export to SD card .........................................................................16
Import from SD ............................................................................16
Suppress menus .................................................................... 18
Suppress models ................................................................... 18
Model basic settings ............................................................. 18
Control mode...............................................................................19
Binding type .................................................................................19
Module.........................................................................................20
Receiver binding ..........................................................................21
Receiver output ...........................................................................22
RF module ....................................................................................22
Range test ....................................................................................22
DSC port .......................................................................................23
Throttle Cut..................................................................................23
Switch-on warning .......................................................................24
Auto trim......................................................................................24
Timer auto reset ..........................................................................24

4 / 80 33028_mc_28_Teil2_jh
Model type ............................................................................ 25
Motor on CH1 ..............................................................................26
Tail ................................................................................................26
Ailerons/Flaps ..............................................................................27
Brake offset ..................................................................................27
Servo adjustment .................................................................. 27
Sticks setting.......................................................................... 29
Controls setting ..................................................................... 29
Dual Rate / Expo.................................................................... 31
Throttle curve ........................................................................ 32
Switch display........................................................................ 34
Control switch........................................................................ 34
Logical switch......................................................................... 35
Announce............................................................................... 35
Phase setting ......................................................................... 36
Motor ...........................................................................37
Phase assignation.................................................................. 38
Phase trim.............................................................................. 38
Channels without delay ........................................................ 39
Timers (general) .................................................................... 39
Phase timer............................................................................ 41
Wing Mix................................................................................ 42
Programming of the wing type....................................................43
Model type: "1AIL" ......................................................................43
Model type: "1AIL 1FLAP"............................................................43
Model type: "2AIL" ......................................................................44
Model types with "2/4AIL 1/2/4FLAP" ........................................45
Model type: "2AIL 1FLAP"............................................................45
Model type: "2AIL 2FLAP"............................................................45
Model type: "2AIL 4FLAP"............................................................46
Model type: "4AIL 2FLAP"............................................................46
Model type: "4AIL 4FLAP"............................................................47
Multiflaps menu...........................................................................48
Brake setting ................................................................................50
AIL-> RUD (aileron-> rudder).......................................................52

5 / 80
33028_mc_28_Teil2_jh
FLAP-> ELE (flaps-> elevator).......................................................52
Free mixers ............................................................................ 53
MIX act. / Phase .................................................................... 56
Only mix channel................................................................... 56
Dual mixer.............................................................................. 57
Fail Safe.................................................................................. 57
Trainer.................................................................................... 58
Transmitter output................................................................ 58
Profitrim................................................................................. 59
Trim memory ......................................................................... 60
Telemetry............................................................................... 60
Channel sequencer................................................................ 61
Multichannel ......................................................................... 62
MP-3 Player ........................................................................... 64
Basic settings ......................................................................... 64
Loudspeaker (LS) Voice / Vario / Buttons ....................................64
Owner ..........................................................................................64
Control mode (preset) .................................................................65
Stick-type (only by mc-26) ...........................................................66
Module.........................................................................................66
DSC port .......................................................................................66
Pitch min ......................................................................................66
Contrast (upper/lower display)....................................................66
Display light..................................................................................66
Switch-on melody ........................................................................67
Battery alarm threshold...............................................................67
Switch-on warning .......................................................................67
Touch sensitivity...........................................................................67
DATA sel........................................................................................67
Ph. Name 1 … 10..........................................................................67
BT headset and following lines....................................................67
Vibration ................................................................................ 68
Servo display.......................................................................... 68
Servo test ............................................................................... 68
Key lock.................................................................................. 68

6 / 80 33028_mc_28_Teil2_jh
Info display ............................................................................ 69
Digital trim / Throttle switch-off trim (function) ................ 69
Heli programming.................................................................. 70
Throttle curve (Heli) .............................................................. 73
Sticks setting (Heli)................................................................ 73
Control adjust (Heli).............................................................. 73
Ring limit................................................................................ 75
Firmware update................................................................... 76
Update through memory card.....................................................76
Update through USB port ............................................................77
Problems during firmware update ..............................................77
Declaration of conformity..................................................... 77
Notes on environmental protection..................................... 78
Care and maintenance .......................................................... 78
Warranty................................................................................ 78

7 / 80
33028_mc_28_Teil2_jh
Introduction
Thank you very much for purchasing the Graupner mc-28 HoTT.
The transmitter manual is composed by two parts. Part 1, the short
manual, is included in this package. Part 2, the programming man-
ual, can be found in its last version on www.graupnerusa.com by
the related page of the transmitter.
Read this manual carefully to safely control your models and to
achieve the best results for your transmitter. If you experience any
trouble during operation look through the instructions, ask your
dealer or contact Graupner Service Centre.
Due to technical changes, the information in this manual may be
changed without prior notice. Keep updated on the products and
firmware by regularly checking our website,
www.graupnerusa.com.
Service Centre
Graupner Central Service
Graupner/SJ GmbH
Henriettenstraße 96
D-73230 Kirchheim/Teck
Servicehotline

(+49) (0)7021/722-130
Monday- Thursday:
9:15 am- 4:00 pm
Friday:
9:15 am- 1:00 pm
[e-mail]
Graupner USA
3941 Park Dr Suite 20-571
El Dorado Hills, CA 95762
Website: www.graupnerusa.com
Phone: [phone]
Email:[email protected]om
Graupner in Internet For the service centers outside Germany please refer to our web site
www.graupnerusa.com

8 / 80 33028_mc_28_Teil2_jh
Use and menu functions
Short-Cuts
The following key combinations can be used to directly call up cer-
tain menus and options:
CLEAR
Brief simultaneous touch of the keys or on the right touch pad
will restore the active entry field's changed parameter value back to
its default value.
"Servo screen"
Brief simultaneous activation of the keys of the left touch pad will
cause a jump to the “Servo” menu from the transmitter's base screen
or almost any menu position.
"Telemetry" menu
Press the center ESC key in the left touch pad for about 1 s to call up
the "Telemetry" menu from the transmitter's base screen.
To come back to the base screen it is enough a "normal" touch on
the ESC key.
Graphic display of telemetry data
Briefly touching one of the selection keys of the left or right touch
pad will cause a jump from the base screen directly to the transmit-
ter's graphic display of telemetry data or will allow paging back and
forth between individual graphic displays.
Briefly touching the ESC or SET key will cause a return back to the
base screen.
"HIDDEN MODE"
Press and hold arrow keys of the left touch pad then momentarily
touch the SET key of the right touch pad.
Key lock
Entry lockout is activated and deactivated from the base screen by
simultaneously pressing the ESC and SET keys for about two seconds.
The key lock function is displayed by a key symbol:
The controls remain operational.
Press the ESC and ENT buttons at the same time again for about two
second to release the lock.
Quick-Select
From the multi-function list, a jump can be made to a "Structure
overview" by a brief, simultaneous touch on the or keys of the
right touch pad.

9 / 80
33028_mc_28_Teil2_jh
Definition of terms
Control function
A control function is the signal for a specific control function. The
signal of a control function can be transmitted directly into one con-
trol channel or through a mixer to several control channels. The con-
trol function includes the influence of the mechanical control path
on the corresponding servo. This can be spread or concentrated and
modified from linear to highly exponential.
Controls
A "control" is the function element that the pilot can operate directly
in the transmitter. The controls connected to the servos, ESC etc. will
be controlled by the receiver.
Control channel
The term control channel is used if a signal contains all control infor-
mation necessary for a particular servo , directly from the control or
indirectly via a mixer.
Mixer
The transmitter software contains a variety of mixing functions.
These allow a control function to influence several control channels
and several servos. Several control function can influence control
channel (one servo).
Switch
The series of toggle switches can be included in the control program-
ming. The switches are generally intended to switch program options
such as to start and stop the timers, turn mixers on and off, etc. Each
switche can be assigned any number of functions.
Control switch
In these software switches, labelled with "G1 ... G8", the switching
point within the control travel can be set by simply pushing a button.
Logical switch
Two switches, controls and logical switches or the combination of
the three can be interconnected in an "AND" or "OR" switch. A total
amount of 8 logical switches "L1 … L8" can be programmed.
Fix switch FXI and FX
This kind of switch always turns a function on or off. You can also
assign to a control function a fix input signal, e.g. FX = +100 % and
FXi =-100 %.

10 / 80 33028_mc_28_Teil2_jh
Receiver configuration
The servos must be connected to the receiver in the indicated
sequence. Outputs that are not assaigned are available. To change
the settings go to the “Model basic setting” menu and then the
"Receiver outputs" line.
Fixed-wing models
Fixed-wing models with and without a motor with up to 4 ailerons
and up to 4 flaps and tail type "normal" or "2 elevator servos"
Tail type "V tail
Delta/flying wing models with and without a motor with up to 4
ailerons/elevators and 4 flap/elevator servos
receiver power supply
free or AILE2 left or special function
free or AILE2 right or special function
aileron or aileron left
free or special fucntion
receiver power supply
airbrake or engine servo or drive controller
aileron right or special function
flap or flap left
flap right or free or special function
free or FLAP2 left or special function
free or FLAP2 right or special function
elevator/rudder left
elevator/rudder right
receiver power supply
free or special function
free or special function
aile/elev left
aile/elev right
free or special function
receiver power supply
Airbrake or motor servo
or ESC for electric models
free or special function
fre or flap / elev left
free or flap / elev right
free or special function or flap 2 / elev left
free or special function or flap 2 / elev right
free or rudder
receiver power supply
free or AILERON2 left or special function
free or AILERON2 right or special function
rudder
AILERON or AILERON left
elevator or elevator1
free or 2nd elevator or special function
receiver power supply
Airbrake or engine servo or electric drive controller
AILERON right or special function
FLAP of FLAP left
FLAP right or free or special function
free or FLAP2 left or special function
free or FLAP2 right or special function

11 / 80
33028_mc_28_Teil2_jh
Helicopter models
Receiver assignment for helicopter models with 1 to 3 swashplate
servos
Receiver assignment for helicopter models with 4 swashplate ser-
vos
Vehicles, boats
receiver power supply
free or special function
free or special function
tail servo (gyro-system)
Roll-1-servo
Nick-1-servo
free or governor or special function
receiver power supply
Pitch- or Roll-2 or Nick-2-servo
free or special function
throttle servo or motor controller
gyro suppression
free or special function
free or special function
receiver power supply
free or special function
free or special function
Tail-servo (gyro-system)
Roll-1-servo
Nick-1-servo
free or governor or special function
receiver power supply
Roll-2-servo
Nick-2-servo
throttle servo or motor controller
gyro suppression
free or special function
free or special function
receiver power supply
free or special function
free or special function
free or special function
steering (left/right function)
free or special function
free or special function
receiver power supply
engine servo or speed controller (forward/backward)
free or special function
free or special function
free or special function
free or special function
free or special function

12 / 80 33028_mc_28_Teil2_jh
Copter
Receiver power supply
receiver power supply
free or special function
free or special function
Yaw
Roll
Nick
free or special function
receiver power supply
Motor/Pitch (up/down)
free or special function
free or special function
free or special function
free or special function
free or special function
special function
V-cable
No. 3936.11
PRX stabilized
receiver power
supply No. 4136
special function
V-cable
No. 3936.11
PRX stabilized
receiver power supply
No. 4136

13 / 80
33028_mc_28_Teil2_jh
Symbols explication
Always pay attention to the information indicated by this warning
sign. Pay particular attention to information additionally marked
CAUTION or WARNING. The signal word WARNING indi-
cates the potential for serious injury The signal word CAUTION
indicates possibility of lighter injuries.
The signal word Note indicates potential malfunctions.
Attention indicates potential damages to objects.
Menus description
The menus described are in the same order as they appear in the
lower display. To switch to the multifunction menu tap on the SET
button in the base display.
Each chapter of the manual is marked with a model type symbol.
These symbols are exactly the same as the ones used in the trans-
mitter. The symbols indicate the relevant paragraph for your model
type. These symbols help find the paragraph required for the model
programming.
Meaning of the warnings
Transmitter input voltage too low
"Bind?"
No receiver is bound to the active model memory. Shortly tap the
SET button to assign the related option.
The receiver of the active model is switched on while a model
change from the “Model select”menu is attempted.
No bound receiver in range.
Should the RF transmission be switched "ON" or "OFF"?
Appears only after switching the transmitter on with an already
bound receiver in active model memory.
Request to switch the RF transmission off
!
Battery
needs
charging !!
BIND?
OK
Warning!
Switch OFF the receiver
first!
CAN‘T
RECEIVE
DATA
OK
RF on/off?
OFF
ON
Please select
Switch
RF module
OFF
OK

14 / 80 33028_mc_28_Teil2_jh
Fail Safe setting not performed yet
Throttle or pitch control stick position or throttle limit for helicop-
ters too high
Connection between teacher and pupil transmitter disturbed
No SD or SDHC memory card in the card slot or card not readable.
The transmitter has not been used within the time set from the line
"Switch-on warning" of the "general settings" menu. An acoustic
warning alarm is emitted, the display shows the warning symbol,
and the WARNING LED on the right side of the On/Off switch
blinks. The transmitter will autonomously switch off after three
minutes of continued inactivity.
In case of too low battery voltage a model change is not possible for
safety reasons. The display shows a related message:
Continue (CONTINUE) or interrupte (INTERRUPT) the "Wireless
Teacher/pupil connection" used before the last switch off of the
transmitter?
Model selection
Tap on the SET button to access the menu. Now you can see the list
of the available model memories. Select the desired model memory
with the or buttons of the left or right touch-pad. Then tap on
the SET button.
To create a new model memory, select an empty model memory:
You will be requested to select one of the five available model types.
Select with the or buttons the appropriate symbol and then tap
on the SET button. The selected model memory will be installed with
the selected model type.
Fail-Safe
setup
t.b.d.
Thr
too
high!
No
pupil
signal
insert
SD card
OK
Power-on warning
is active!!!
actually not possible
voltage too low
Please select
Trainer connection?
ON OFF
Copy / Erase
Suppress menus
Suppress models
Model select
Base setup model
Model type
03
04
05
 free
02
01
06
R12
 free
 free
 free
 free
M

15 / 80
33028_mc_28_Teil2_jh
The selected model specific settings will be available in the menus.
Now you can program your model in this model memory.
The display changes to the base display of the new assigned model
memory after the initialization of the selected model memory. Con-
currently, a warning message that there is no connection with a
receiver will appear for a couple of seconds. Tap on the SET button
to directly enter the "Base menu". Here you are directly in the line
for binding. For more information on the binding process, please
read the details under the "Model base setting" menu description.
Tap on the ESC button to procede without binding.
Copy/Delete
Tap on the SET button to access the menu. Now you can see the list
of the available functions. On the right side of the display there is a
scrollbar. The scrollbar indicates that there are additional menu
items. Scroll with the selection buttons up or down.
Delete model
Select the "delete model" item and confirm with the SET button. On
the lower left side you can see an arrow facing down. The arrow indi-
cates that there are additional menu items. Scroll with the selection
buttons up or down.
Note
This deletion cannot be restored. All of the data in the selected
model memory is completely deleted.
If the active model memory is deleted, a favorite model type must
be defined soon after the deletion process. If an inactive model
memory is deleted,"àààfreeààà" appears soon after the model
selection.
Use the selection buttons  of the left or right touch-pad to select
the model to delete.
A safety question will appear. The deletion process will be performed
only if you move to YES and tap on the SET button. Selecting NO and
tapping on SET button interrupts the deletion process.
BIND?
OK
Select model type
Model select
Base setup model
Model type
Copy / Erase
Suppress menus
Suppress models
Copy phase
Erase model
Copy model–>model
=>
=>
=>
Export to SD
Import from SD =>
=>
=>
=>
01
03
04
05 frei 
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
Model to be erased:
R12
R12
R12
–––
M
M
G
M
Model really
GRAUBELE
to be erased ?
NO YES
01

16 / 80 33028_mc_28_Teil2_jh
Copy Mod¢Mod
Select the point "Copy Mod¢Mod" and confirm with the SET but-
ton.
You can always interrupt the process with the ESC button.
• Select the model to copy and confirm the selection with the SET
button.
• Select the target memory and confirm with the SET button.
A safety question will appear. If you select YES and press the SET but-
ton, the copy process will be performed. If you select NO, the copy
process will be interrupted.
Export to SD card
Select the "Export to SD" point and confirm with the SET button.
You can always interrupt the process with the ESC button.
Select the model to export and confirm the selection with the SET
button.
A safety question will appear. If you select YES and press the SET but-
ton, the export process will be performed. If you select NO, the pro-
cess will be interrupted.
Import from SD
Select the "Import from SD" point and confirm with the SET button.
You can always interrupt the process with the ESC button.
• Select the model to export from the SD card and confirm with
the SET button.
• Select the target memory and confirm with the SET button.
A safety question will appear. If you select YES and press the SET but-
ton, the import process will be performed. If you select NO, the
import process will be interrupted.
Note
The receiver connection remains if the imported model memory has
been created in the transmitter and is imported to the same model
memory. The receiver must be bound again if the model memory is
imported in another transmitter.
01
03
04
05 frei
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
Copy from model:
R12
R12
–––
R12
M
M
G
M
Model
ULTIMATE
export ?
NO YES
01
SD-CARD
Copy phase
Erase model
Copy model–>model
=>
=>
=>
Export to SD
Import from SD =>
=>
=>
=>
Model
ULTIMATE
export ?
NO YES
01
SD-CARD
05 frei
EXTRA
ALPINA
COBRA
BELL47G
Import from SD-CARD:
16/08/10
16/08/11
16/08/12
16/08/13
01
03
04
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
Import to model:
05 free
R12
R12
R12
–––
M
M
G
M

17 / 80
33028_mc_28_Teil2_jh
Copy phase
Select the "Copy phase" point and confirm with the SET button.
You can always interrupt the process with the ESC button.
• Select the phase to copy and confirm the selection with the SET
button.
• Select the target phase and confirm the selection with the SET
button.
A safety question will appear. If you select YES and press the SET but-
ton, the copy process will be performed. If you select NO, the copy
process will be interrupted.
Permanently save changes / undo changes
The last state of the programming of the model is saved in the model
memory if you perform a model change or if you switch the trans-
mitter off. The change will be manually edited during the use with
the “Permanently save changes / undo changes” function.
You can immediately and permanently save the edited programming
in the model memory with the “Permanently save changes / undo
changes” menu point.
You can undo programming changes implemented during use with
the “Permanently save changes / undo changes” menu point. This
menu point can restore the last performed programming. You can
choose when the undo action should start, either the last switch-off
or the last manual saving.
A safety question will appear. If you select YES and press the SET but-
ton, the related process will be performed. If you select NO the pro-
cess will be interrupted.
7
Copy to phase:
3
5=>
=>
2
4
6
1
Copy phase
Erase model
Copy model–>model
=>
=>
=>
Export to SD
Import from SD =>
=>
=>
=>
7
Copy from phase:
3
5=>
=>
2
4
6
1
Copy phase
=>
=>
=>
Export to SD
Import from SD
=>
=>
=>
=>
Store changes
undo changes
Copy phase
=>
=>
=>
Export to SD
Import from SD
=>
=>
=>
=>
Store changes
undo changes

18 / 80 33028_mc_28_Teil2_jh
Suppress menus
In this menu you can hide specific menu points from the menu func-
tion list. The hiding is related to the model memory.
Select the menu point to hide or to show and switch the status with
the SET button. The crossed-out menu points are then no longer dis-
played in the multifunction list.
The menu points are not deactivated. Programmed functions in the
hidden menus remain active.
Suppress models
In this menu you can hide model memories from the model selec-
tion list.
Select the model memory to hide or to display then tap on the SET
button to switch the status. The crossed-out model memories are
no longer displayed in the model selection list.
The model memories will not be deactivated. The programmed
options will be retained.
Model basic settings
In this menu you can set the base setting for the model memory.
Model name
You can insert a maximum of nine characters for a model name of
the active model memory.
With the left and right selection buttons you can move up or down
to the next place. With the SET button you can confirm the selection
and move to the next place. You can insert an empty space by tap-
ping simultaneously the up and down or left and right buttons.
You can leave the menu with the ESC button.
Suppress models
Model select
Base setup model
Model type
Copy / Erase
Suppress menus
Model select
Base setup model
Model type
Copy / Erase
Suppress models
Suppress : SET
Model select
Base setup model
Model type
Copy / Erase
Suppress menus
Suppress models
01
03
04
05
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
R12
R12
R12
–––
 free
Suppress : SET
M
M
G
M
Model type
Suppress models
Base setup model
Servo adjustment
Control adjust
Stick mode
Mod. Name
Stick mode
Module
1
n/a
Base setup model
bind
BD2
BD1
Rcv Ch Map n/a
HoTT
R08
!"#$%&’()�+,–./0123
456789:;
Mod Name GRAUB
FGHIJKLMNOPQRSTUVWX
YZ[¥]^_`abcdefghijk
?@ ABCDE

19 / 80
33028_mc_28_Teil2_jh
Control mode
In this function you can choose a control mode to be used for a
model memory. This function associates a control stick’s control
movement with a specific channel. Tap n the SET button, set the
desired mode through the selection buttons. In the "receiver assig-
nation" section you can see where each servo should be connected.
Binding type
Note
This menu line is only visible if there is no receiver bound to the
active model memory.
A binding type must be selected before the binding of a receiver. You
can select between "Global" and "Model".
"Global": All bound receivers react to the signals of each model
memory of the transmitter. For safety reasons, the model memory
can only be changed after switching the receiver off.
"Model": Bound receivers react only to the signals of the assigned
model memory. Accidental use through a non assigned model mem-
ory is not possible.
Mod. Name
Stick mode 1
Base setup model
SEL
GRAUBELE
n/a
bind
Module HoTT
Rcv Ch Map n/a
R08
Fixed-wing model Helicopter model / Copter model
Mod. Name
Control mode 1
Base setup model
SEL
GRAUBELE
n/a
n/a
Module HoTT
Binding type Model
Car / boat
MODE 2 (Throttle left)
Nick
Nick
Tail rotor
Tail rotor
Motor / Pitch
Motor / Pitch
Roll
Roll
Motor / Pitch
Motor / Pitch
Tail rotor
Tail rotor
Nick
Nick
Roll
Roll
Nick
Nick
Roll
Roll
Motor / Pitch
Motor / Pitch
Tail rotor
Tail rotor
Motor / Pitch
Motor / Pitch
Roll
Roll
Nick
Nick
Tail rotor
Tail rotor
MODE 1 (Throttle right)
MODE 3 (Throttle right) MODE 4 (Throttle left)
MODE 2 (Throttle left)
Elevator
Elevator
Rudder
Rudder
Full throttle
Motor idle
Querruder
Querruder
Full throttle
Motor idle
Rudder
Rudder
Elevator
Elevator
Aileron
Aileron
Elevator
Elevator
Aileron
Aileron
Full throttle
Motor idle
Rudder
Rudder
Full throttle
Motor idle
Aileron
Aileron
Elevator
Elevator
Rudder
Rudder
MODE 1 (Throttle right)
MODE 3 (Throttle right) MODE 4 (Throttle left)
MODE 2 (for/backward left)
left
right
forward/backward
forward/backward
forward/backward
forward/backward
left
right
forward/backward
forward/backward
left
right
forward/backward
forward/backward
left
right
MODE 1 (for/backward right)
MODE 3 (for/backward right) MODE 4 (for/backward left)

20 / 80 33028_mc_28_Teil2_jh
The binding type is indicated in the model memory list near the
model memory name:
"G" means global binding
"M" means model memory specific binding
Module
You can select the fields in the lines with the left and right selection
buttons . In the first "HoTT" field you have the following selection
possibilities:
HoTT- the integrated HoTT module will be used for the signal trans-
mission.
The following settings (EXT. and SP.) are included for eventual exter-
nal RF modules of other manufacturers. They do not work with HoTT
receivers.
EXT.- the signal transmission is emitted through the DSC port to an
optional external RF module. Here the value PPM 10 is set (max. 10
control channels). The "Range test" and "Receiver outputs" func-
tions are not available. Underneath appears a new line. Here you can
set the PPM signal to be emitted normally or inverted.
S P. - The signal transmission will be emitted as a special digital signal
through the DATA port. The binding will be performed through the
"BIND" field. Two new lines will appear underneath. In the first line
the number of the emitted channels
(6 or 8) will be set. In the second line you can set the signal to be
emitted normally or inverted. The "Range test" and "Receiver out-
puts" functions are not available.
If the external RF module has to be powered with the current com-
ing from the DATA port, then pay attention to the following informa-
tion:
Note
The output voltage of the DATA port of about 5 V must be reduced
through a stabilized step-down module to 3 / 3,3 V.
Pay attention to the switch scheme:
01
03
04
05 free
ULTIMATE
02
GRAUBELE
STARLET
BELL47G
R12
R12
R12
–––
M
M
G
M
06 free
Mod. name
Stick mode 1
n/a
Base setup model
bind
BD1
GRAUBELE
BD2
Rcv Ch Map R12 n/a
Module HoTT
Mod. name
Stick mode 1
Base setup model
SEL
GRAUBELE
PPM10
Module
EXT.PPM sig. normal
EXT.
Mod. name
Stick mode 1
Base setup model
BD
GRAUBELE
Module
SP channel 6
S P. BIND1
Mod
GND
Vcc IN = 5 V
DATA +
DATA S 125000 baud signal
Vcc
GND
DATA -
22µF/6.3 V 22µF/6.3 V
Vcc OUT = 3 ... 3.3 V
Low Drop
Voltage
Regulator SP.-MODULE
with
digital input signal