Gree GWH09ACC-K6DNA1A/I User manual

Change for life
AIR CONDITIONER
Owner's Manual
Original Instructions
Thank you for choosing our product.
Please read this Owner’
retain it for future reference.
If you have lost the Owner's Manual, please contact the local agent
or visit www.gree.com or send an email to [email protected] for
the electronic version.
s Manual carefully before operation and
Split Air Conditioner

GWH12ACC-K6DNA1D/I
GWH12ACC-K6DNA2D/I
GWH12ACC-K6DNA3D/I
GWH18ACD-K6DNA1D/I
GWH18ACD-K6DNA2D/I
GWH24ACE-K6DNA1A/I
GWH24ACE-K6DNA2A/I
GWH24ACE-K6DNA3A/I
GWH12ACC-K6DNA5D/I
GWH12ACC-K6DNA4D/I
GWH24ACE-K6DNA4A/I
GWH24ACE-K6DNA5A/I
GWH18ACD-K6DNA3D/I
GWH18ACD-K6DNA4D/I
GWH18ACD-K6DNA5D/I
GWC24ACE-K6DNA1A/I
GWH09ACC-K6DNA1A/I
GWH09ACC-K6DNA2A/I
GWH09ACC-K6DNA3A/I
GWH09ACC-K6DNA4A/I
GWH09ACC-K6DNA5A/I

This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
1) Frequency band(s) in which the radio equipment operates：2400MHz-2483.5MHz
2) Maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment
If it needs to install, move or maintain the air conditioner, please contact dealer or local service
center to conduct it at first. Air conditioner must be installed, moved or maintained by appointed
unit. Otherwise, it may cause serious damage or personal injury or death.
operates：20dBm
This marking indicates that this product should not be disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
R32: 675
Content
Operation Notices
7KH5HIULJHUDQW
3UHFDXWLRQV
3DUWV1DPH
ScreenOperation Guide
%XWWRQVRQUHPRWHFRQWUROOHU
,QWURGXFWLRQIRULFRQVRQGLVSOD\VFUHHQ
,QWURGXFWLRQIRUEXWWRQVRQUHPRWHFRQWUROOHU
)XQFWLRQLQWURGXFWLRQIRUFRPELQDWLRQEXWWRQV
2SHUDWLRQJXLGH
5HSODFHPHQWRIEDWWHULHVLQUHPRWHFRQWUROOHU
(PHUJHQF\RSHUDWLRQ
Maintenance
&OHDQDQG0DLQWHQDQFH
Malfunction
0DOIXQFWLRQDQDO\VLV
Installation Notice
6DIHW\RSHUDWLRQRIIODPPDEOHUHIULJHUDQW
,QVWDOODWLRQGLPHQVLRQGLDJUDP
6DIHW\SUHFDXWLRQVIRULQVWDOOLQJDQGUHORFDWLQJWKHXQLW
7RROVIRULQVWDOODWLRQ
6HOHFWLRQRILQVWDOODWLRQORFDWLRQ
5HTXLUHPHQWVIRUHOHFWULFFRQQHFWLRQ
Installation
,QVWDOODWLRQRILQGRRUXQLW
&KHFNDIWHULQVWDOODWLRQ
Test and operation
7HVWRSHUDWLRQ
Attachment
&RQILJXUDWLRQRIFRQQHFWLRQSLSH
3LSHH[SDQGLQJPHWKRG

Explanation of Symbols
Exception Clauses
Indicates a hazardous situation that, if not avoided, will
Manufacturer will bear no responsibilities when personal injury or
1.Damage the product due to improper use or misuse of the product;
2.Alter, change, maintain or use the product with other equipment without abiding
by the instruction manual of manufacturer;
product;
4.After verification, defects are due to improper operation during transportation of
regulations;
5.Operate, repair, maintain the unit without abiding by instruction manual or related
performance of parts and components that produced by other manufacturers;
6.After verification, the problem or dispute is caused by the quality specification or
majeure.
7.The damage is caused by natural calamities, bad using environment or force
3.After verification, the defect of product is directly caused by corrosive gas;
property loss is caused by the following reasons.
result in death or serious injury.
Indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
Indicates a hazardous situation that, if not avoided, may
result in minor or moderate injury.
Indicates important but not hazard-related information,
used to indicate risk of property damage.
Indicates a hazard that would be assigned a signal word
WARNING or CAUTION.
DANGER
WARNING
CAUTION
NOTICE

1
The Refrigerant
WARNING
To realize the function of the air conditioner unit, a special refrigerant circulates in
the system. The used refrigerant is the fluoride R32, which is specially cleaned.
The refrigerant is flammable and inodorous. Furthermore, it can leads to explosion
under certain conditions. But the flammability of the refrigerant is very low. It can
be ignited only by fire.
Compared to common refrigerants, R32 is a nonpolluting refrigerant with no harm
to the ozonosphere. The influence upon the greenhouse effect is also lower. R32
has got very good thermodynamic features which lead to a really high energy
efficiency. The units therefore need a less filling.
Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacture. Should repair be necessary, contact your nea-
rest authorized Service Centre. Any repairs carried out by unqualified personnel
may be dangerous. The appliance shall be stored in a room without continuously
operating ignition sources. (for example: open flames, an operating gas appliance
or an operating electric heater.) Do not pierce or burn.
Appliance shall be installed, operated and stored in a room with a floor area larger
than X.m
Appliance filled with flammable gas R32. For repairs, strictly follow manufacturer’s
instructions only. Be aware that refrigrants not contain odour. Read specialist’s
manual.
2
Appliance filled with flammable gas R32.
Before use the appliance, read the owner’s manual first.
Before repair the appliance, read the service manual first.
Before install the appliance, read the installation manual first.
(Please refer to table "a" in section of " Safety Operation of Inflammable
Refrigerant" for Space X.)

Precautions
:$51,1*
'RQRWFRQQHFWDLUFRQGLWLRQHUWRPXOWLSXUSRVHVRFNHW
7KLVDSSOLDQFHFDQEHXVHGE\FKLOGUHQDJHGIURP
Operation and Maintenance
,IWKHVXSSO\FRUGLVGDPDJHGLWPXVWEHUHSODFHGE\
WKHPDQXIDFWXUHULWVVHUYLFHDJHQWRUVLPLODUO\TXDOLILHG
SHUVRQVLQRUGHUWRDYRLGDKD]DUG
'R QRWVSUD\ZDWHU RQ LQGRRU XQLW,WPD\FDXVH HOHFWULF
VKRFNRU PDOIXQFWLRQ
2WKHUZLVHLWPD\FDXVHILUHKD]DUG
&KLOGUHQVKDOOQRWSOD\ZLWKWKHDSSOLDQFH
&OHDQLQJDQGXVHUPDLQWHQDQFHVKDOOQRWEHPDGHE\
FKLOGUHQZLWKRXWVXSHUYLVLRQ
\HDUVDQGDERYHDQGSHUVRQVZLWKUHGXFHGSK\VLFDO
VHQVRU\RUPHQWDOFDSDELOLWLHVRUODFNRIH[SHULHQFH
DQGNQRZOHGJHLIWKH\KDYHEHHQJLYHQVXSHUYLVLRQRU
LQVWUXFWLRQFRQFHUQLQJXVHRIWKHDSSOLDQFHLQDVDIH
ZD\DQGXQGHUVWDQGWKHKD]DUGVLQYROYHG
'RQRWZDVKWKHDLUFRQGLWLRQHUZLWKZDWHUWRDYRLG
HOHFWULFVKRFN
$IWHUUHPRYLQJWKHILOWHUGRQRWWRXFKILQVWRDYRLGLQMXU\
'RQRWXVHILUHRUKDLUGU\HUWRGU\WKHILOWHUWRDYRLG
GHIRUPDWLRQRUILUHKD]DUG
'RGLVFRQQHFWSRZHUVXSSO\ZKHQFOHDQLQJDLU
FRQGLWLRQHU2WKHUZLVHLWPD\FDXVHHOHFWULFVKRFN



'RQRWEORFNDLURXWOHWRUDLULQOHW,WPD\FDXVH
PDOIXQFWLRQ
UHPRWHFRQWUROOHUPD\EHEURNHQ
Ɣ3RZHUFRUGLVRYHUKHDWLQJRUGDPDJHG
Ɣ7KHUH¶VDEQRUPDOVRXQGGXULQJRSHUDWLRQ
Ɣ&LUFXLWEUHDNWULSVRIIIUHTXHQWO\
Ɣ$LUFRQGLWLRQHUJLYHVRIIEXUQLQJVPHOO
Ɣ,QGRRUXQLWLVOHDNLQJ
FRQWDFWWKHGHDOHURUTXDOLILHGSURIHVVLRQDOVIRUVHUYLFH
:KHQWXUQLQJRQRUWXUQLQJRIIWKHXQLWE\HPHUJHQF\
RSHUDWLRQVZLWFKSOHDVHSUHVVWKLVVZLWFKZLWKDQLQVXODWLQJ
REMHFWRWKHUWKDQPHWDO
RXWOHW,WPD\FDXVHSHUVRQDOLQMXU\RUGDPDJH
Precautions
:$51,1*
FRQGLWLRQHUDQGGLVFRQQHFWSRZHULPPHGLDWHO\DQGWKHQ
,IWKHDLUFRQGLWLRQHURSHUDWHVXQGHUDEQRUPDOFRQGLWLRQV
LWPD\FDXVHPDOIXQFWLRQHOHFWULFVKRFNRUILUHKD]DUG
'RQRWVSLOOZDWHURQWKHUHPRWHFRQWUROOHURWKHUZLVHWKH
HOHFWULFVKRFNRUGDPDJH3OHDVHFRQWDFWGHDOHUZKHQ
\RXQHHGWRUHSDLUDLUFRQGLWLRQHU
'RQRWUHSDLUDLUFRQGLWLRQHUE\\RXUVHOI,WPD\FDXVH
REMHFWV,WPD\FDXVHGDPDJHRUSHUVRQDOLQMXU\
'RQRWVWHSRQWRSSDQHORIRXWGRRUXQLWRUSXWKHDY\
:KHQEHORZSKHQRPHQRQRFFXUVSOHDVHWXUQRIIDLU
'RQRWH[WHQGILQJHUVRUREMHFWVLQWRDLULQOHWRUDLU
0DLQWHQDQFHPXVWEHSHUIRUPHGE\TXDOLILHG
SURIHVVLRQDOV2WKHUZLVHLWPD\FDXVHSHUVRQDOLQMXU\
RUGDPDJH


'RLQVWDOOWKHFLUFXLWEUHDN,IQRWLWPD\FDXVHPDOIXQFWLRQ
RIDWOHDVWPPLQDOOSROHVVKRXOGEHFRQQHFWHGLQIL[HG
ZLULQJ
PDJQHWEXFNOH DQGKHDWLQJEXFNOHIXQFWLRQLWFDQSURWHFW
WKHFLUFXLWVKRUWDQG RYHUORDG
SRZHUVXSSO\FLUFXLWDQGFLUFXLWEUHDN
Precautions
:$51,1*
QRWH WKHIROORZLQJWDEOH$LUVZLWFKVKRXOGEHLQFOXGHG
0DNHVXUHWKHSRZHUVXSSO\PDWFKHVZLWKWKH
UHTXLUHPHQWRIDLUFRQGLWLRQHU8QVWDEOHSRZHUVXSSO\RU
LQFRUUHFWZLULQJRUPDOIXQFWLRQ3OHDVHLQVWDOOSURSHUSRZHU
VXSSO\FDEOHVEHIRUHXVLQJWKHDLUFRQGLWLRQHU
$QDOOSROHGLVFRQQHFWLRQVZLWFKKDYLQJDFRQWDFWVHSDUDWLRQ
0XVWIROORZWKHHOHFWULFVDIHW\UHJXODWLRQVZKHQLQVWDOOLQJ
WKHXQLW
JURXQGLQJZLUHRISRZHUVRFNHW
3URSHUO\FRQQHFWWKHOLYHZLUHQHXWUDOZLUHDQG
DQ\ZRUNUHODWHGWRHOHFWULFLW\DQGVDIHW\
%HVXUHWRFXWRIIWKHSRZHUVXSSO\EHIRUHSURFHHGLQJ
,QFOXGLQJDQFLUFXLWEUHDNZLWKVXLWDEOHFDSDFLW\SOHDVH
$LU&RQGLWLRQHUVKRXOGEHSURSHUO\JURXQGHG,QFRUUHFW
'RQWXVHXQTXDOLILHGSRZHUFRUG
JURXQGLQJPD\FDXVHHOHFWULFVKRFN
$FFRUGLQJWRWKHORFDOVDIHW\UHJXODWLRQVXVHTXDOLILHG
,QVWDOODWLRQPXVWEHSHUIRUPHGE\TXDOLILHGSURIHVVLRQDOV
2WKHUZLVHLWPD\FDXVHSHUVRQDOLQMXU\RUGDPDJH
Attachment


,QVWDOODWLRQPXVWEHSHUIRUPHGLQDFFRUGDQFHZLWKWKH
SHUVRQVLQRUGHUWRDYRLGDKD]DUG
PXVWEHSURSHUO\JURXQGLQJZLWKVSHFLDOL]HGJURXQGLQJ
GHYLFHE\DSURIHVVLRQDO3OHDVHPDNHVXUHLWLVDOZD\V
JURXQGHGHIIHFWLYHO\RWKHUZLVHLWPD\FDXVHHOHFWULFVKRFN
7KHDSSOLDQFHPXVWEHSRVLWLRQHGVRWKDWWKHSOXJLV
DFFHVVLEOH
,IWKHOHQJWKRISRZHUFRQQHFWLRQZLUHLVLQVXIILFLHQWSOHDVH
FRQWDFWWKHVXSSOLHUIRUDQHZRQH$YRLGH[WHQGLQJWKH
ZLUHE\\RXUVHOI
$OOZLUHVRILQGRRUXQLWDQGRXWGRRUXQLWVKRXOGEH
FRQQHFWHGE\DSURIHVVLRQDO
QDWLRQDOZLULQJUHJXODWLRQV
UHTXLUHPHQWRI1(&DQG&(&E\DXWKRUL]HGSHUVRQQHO
RQO\
Precautions
:$51,1*
ZLUHZKLFKFDQWEHXVHGIRURWKHUSXUSRVHV
7KHJURXQGLQJUHVLVWDQFHVKRXOGFRPSO\ZLWKQDWLRQDO
HOHFWULFVDIHW\UHJXODWLRQV
7KHDLUFRQGLWLRQHULVWKHILUVWFODVVHOHFWULFDSSOLDQFH,W
NHHSWKHLQWHUFRQQHFWLRQFDEOHDZD\IURPWKHFRSSHU
WXEH
7KHWHPSHUDWXUHRIUHIULJHUDQWFLUFXLWZLOOEHKLJKSOHDVH
WKHPDQXIDFWXUHULWVVHUYLFHDJHQWRUVLPLODUO\TXDOLILHG
,IWKHVXSSO\FRUGLVGDPDJHGLWPXVWEHUHSODFHGE\
7KH\HOORZJUHHQZLUHLQDLUFRQGLWLRQHULVJURXQGLQJ
7KHDSSOLDQFHVKDOOEHLQVWDOOHGLQDFFRUGDQFHZLWK
'RQRWSXWWKURXJKWKHSRZHUEHIRUHILQLVKLQJLQVWDOODWLRQ


The indoor unit should be installed close to the wall.
Instructions for installation and use of this product are
provided by the manufacturer.
Precautions
WARNING
place, only the qualified person can perform the work.
Otherwise, it may cause personal injury or damage.
If you need to relocate the air conditioner to another
must be installed in the line.
For the air conditioner without plug, an circuit break
far away from animals or plants.If it is unavoidable,
please add the fence for safety purpose.
Select a location which is out of reach for children and
reachable after finishing installation.
For the air conditioner with plug, the plug should be
Indoor side DB/WB(ćOutdoor side DB/WB(ć
Maximum cooling 32/23 43/26
Maximum heating 27/- 24/18
Working temperature range
6
Ɣerutarepmet-woLrof)erutarepmetroodtuo(egnarerutarepmetgnitarepoehT
cooling only unit is -15ć~ 43ć; for Low-temperature heat pump unit is
-22ć~ 43ć.
Indoor side DB/WB(ć) Outdoor side DB/WB(ć)
Maximum cooling 32/23 48/30
Maximum heating 27/- 24/18
ƔThe operating temperature range (outdoor temperature) for cooling only unit is
NOTICE:
NOTICE:
-15ć~ 48ć
For model:GWC24ACE-K6DNA1A
For some models:


display
power
indicator
temp.
indicator
receiver
window
Display
'LVSOD\FRQWHQWRUSRVLWLRQPD\EHGLIIHUHQWIURPDERYH
JUDSKLFVSOHDVHUHIHUWRDFWXDOSURGXFWV
UHPRWHFRQWURO
NOTICE:
$FWXDOSURGXFWPD\EHGLIIHUHQWIURPDERYHJUDSKLFVSOHDVHUHIHUWRDFWXDO
SURGXFWV
DLULQOHW
SDQHO
ILOWHU
DX[EXWWRQ
KRUL]RQWDOORXYHU
DLURXWOHW
Parts Name
Indoor Unit


Buttons on remote controller
Introduction for icons on display screen















EXWWRQ
EXWWRQ
 EXWWRQ
 7(03EXWWRQ
6/((3EXWWRQ
212))EXWWRQ
02'(EXWWRQ
)$1EXWWRQ
785%2EXWWRQ

Ÿ
ŸEXWWRQ
6HQGVLJQDO
7XUERPRGH
6FDYHQJLQJIXQFWLRQV
ćKHDWLQJIXQFWLRQ
6HWWHPSHUDWXUH
6HWWLPH ;)$1IXQFWLRQ
7,0(5217,0(52))
&KLOGORFN
8SGRZQVZLQJ
/HIWULJKWVZLQJ
/LJKW
7HPSGLVSOD\W\SH
6HWWHPS
2XWGRRUDPELHQWWHPS
,QGRRUDPELHQWWHPS
6OHHSPRGH
&ORFN
+HDWPRGH
)DQPRGH
'U\PRGH
&RROPRGH
$XWRPRGH
2SHUDWLRQPRGH
,IHHO
+HDOWK\PRGH
4XLHW
:L)L 7KLVLVDJHQHUDOUHPRWHFRQWUROOHU6RPH
PRGHOVKDYHWKLVIXQFWLRQZKLOHVRPH
GRQRW3OHDVHUHIHUWRWKHDFWXDOPRGHOV
^
6HWIDQVSHHG
,)((/EXWWRQ
 7,0(5217,0(52))EXWWRQ
 &/2&.EXWWRQ
 48,(7EXWWRQ
 :L)LEXWWRQ
 /,*+7EXWWRQ

9
Ɣ
ƔAfter selecting cool mode, air conditioner will operate under cool mode. Cool
indicator " " on indoor unit is ON (This indicator is not available for some
models). Pres
Ÿ
VŸRUEXWWRQWRDdjust set temperature. Press "FAN"
button to adjust fan speed. Press " " / " " button to adjust fan blowing angle.
ƔWhen selecting dry mode, the air cond tioner operates at low speed under dry
mode. Dry indicator " " on indoor unit is ON (This indicator is not available
for some models). Under dry mode, fan speed can’t be adjusted.
Press " " / " " button to adjust fan blowing angle.
Ɣdnagniloocon,nafwolbylnolliwrenoitdnocriaeht,edomnafgnitcelesnehW
no heating. All indicators are OFF,Operation indicator is ON. Press "FAN" button
ƔAfter putting through the power, the air conditioner will give out a sound.
Operation indicator " " is ON (red indicator the colour is different for different
models). After that, you can operate the air conditioner by using remote controller.
Ɣ
Under on status, pressing the button on the remote controller, the signal icon " "
on the display of remote controller will blink once and the air conditioner will give
out a “d
Ɣ
As for the models with functions of WiFi or wired controller, the indoor unit must
has been controlled by standard remote controller under auto mode first, and then
the function of adjustable temperature under auto mode can be realized by APP
or the wired controller.
Ɣ
This remote controller can adjust the temperature under auto mode. When matching
with the unit which is without the function of adjustable temperature under auto mode,
the set temperature under auto mode may be invalid, or the displayed set temperature
on the unit is not same as that on the remote controller under auto mode.
i” sound, which means the signal has been sent to the air conditioner.
MODE button
2
1ON/OFF button
Press this button to turn on the unit. Press this button again to turn off the unit.
Press this button to select your required operation mode.
AUTO COOL DRY FAN HEAT
" " / " " button can adjust fan blowing angle.
ƔThis is a general use remote controller it could be used for the air conditioners
with multifunction; For some function, which the model doesn't have, if press
the corresponding button on the remote controller that the unit will keep the
original running status.
Introduction for buttons on remote controller
Note:
gnidroccayllacitamotuaetarepolliwrenoitidnocria,edomotuagnitcelesnehW
to the sensed temperature. Press "FAN" button can adjust fan speed. Press

ƔFor preventing cold air, after starting up heating mode, indoor unit will delay 1~5
Ɣ
ƔUnder auto mode, temperature can be displayed;Under auto mode,
,
Low-Medium speed
Medium-High speed
Medium speed
High speed
Ɣ
Ɣ
10
Introduction for buttons on remote controller
Note:
set temperature can be adjusted.
to
Auto
Low speed
Note:
Ɣ
It’s Low fan speed under Dry mode
X-FAN function Hold fan speed button for 2s in COOL or DRY mode, the icon “ ” is
displayed and the indoor fan will continue operation for a few minutes in order to dry
the indoor unit even though you have turned off the unit. After energization, X-FAN
OFF is defaulted. X-FAN is not available in AUTO, FAN or HEAT mode.
4TURBO button
Under COOL or HEAT mode, press this button to turn to quick COOL or quick
HEAT mode. " " icon is displayed on remote controller. Press this button again
to exit turbo function and " " icon will disappear.
3FAN button
This button is used for setting Fan Speed in the sequence that goes from AUTO,
,, ,then back to Auto.
Having set X-FAN function on: After turning off the unit by pressing ON/OFF
button indoor fan will continue running for a few minutes. at low speed. In this
period, Hold fan speed button for 2s to stop indoor fan directly.
Having set X-FAN function off: After turning off the unit by pressing ON/OFF
button, the complete unit will be off directly.
This function indicates that moisture on evaporator of indoor unit will be blowed
after the unit is stopped to avoid mould.
Ɣ
minutes to blow air (actual delay time is depend on indoor ambient temperature).
Set temperature range from remote controller: 16~30ć(61-86°F);
Fan speed: auto, low speed, low-medium speed,medium speed, medium-high
speed,high speed.
to adjust fan speed. Press" " / " " button to adjust fan blowing angle.
ƔWhen selecting heating mode, the air conditioner operates under heat mode.
Heat indicator " " on indoor unit is ON (This indicator is not available for some
PRGHOV3UHVVŸRUEXWWRQWRDGMXVWVHWWHPSHUDWXUH3UHVV)$1EXWWRQ
to adjust fan speed. Press " " / " " button to djust fan blowing angle. (Cooling
only unit won’t receive heating mode signal. If setting heat mode with remote
controller, press ON/OFF button can’t start up the unit).
Ÿ

6
Ɣ
Ɣ
The
7
Ɣ
Ɣ
Ɣ
Ɣ
Press this button can select left & right swing angle. Fan blow angle can be selected
circularly as below:
Press this button can select up & down swing angle. Fan blow angle can be selected
circularly as below:
Note:
Ɣ
no display
(horizontal louvers stops
at current position)
When selecting " ", air conditioner is blowing fan automatically. Horizontal
louver will automatically swing up & down at maximum angle.
When selecting " ǃǃǃǃ DLUFRQGLWLRQHULVEORZLQJIDQDW¿[HG
position. Horizontal louver will stop at the¿[HGSRVLWLRQ
When selecting " ǃǃ DLUFRQGLWLRQHULVEORZLQJIDQDW¿[HGDQJOH
+RUL]RQWDOORXYHUZLOOVHQGDLUDWWKH¿[Hd angle.
Hold " " button above 2s to set your required swing angle. When reaching your
required angle, release the button.
When setting TIMER ON, TIMER OFF oU&/2&.SUHVVŸRUEXWWRQWR
Ÿ
adjust time. (Refer to CLOCK, TIMER ON, TIMER OFF buttons) When setting
TIMER ON, TIMER OFF or CLOCK, press "Ÿ" or "
Ÿ
" button to adjust time. (Refer
to CLOCK, TIMER ON, TIMER OFF buttons)
Introduction for buttons on remote controller
Ɣ
The function is only available for some model.
Press this button continuously more than 2s, the main unit will swing back an
forth from left to right, and then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immediately.
Under swing left and right mode, when the status is switched from off to , if
press this button again 2s later, status will switch to off status directly; if press
this button again within 2s, the change of swing status will also depend on the
circulation sequence stated above.
Ɣ
so that the ambient temp. approachs the preset temp. as soon as possible.
Ÿ
ŸEXWWRQ
5
+ROGLQJŸRUEXWWRQVODW
Ÿ
er, set temperature on remote controller will
change quickly2QUHOHDVLQJEXWWRQDIWHUVHWWLQJLV¿QLVKHGWHPSHUDWXUHLQGica-
tor on indoor unit will change accordingly.
3UHVVŸRU" " button once increase or decrease set temperature 1
ć(°F).
If start this function, the unit will run at super-high fan speed to cool or heat quickly
11

12
Introduction for buttons on remote controller
the Sleep, circulate between these, after electrified, Sleep Cancel is defaulted.
Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run for one hour, the
main unit setting temperature will increase 1 , two hours, setting temperature increa-
sed 2 , then the unit will run at this setting temperature; In Heat mode: sleep status
after run for one hour, the setting temperature will decrease 1 , two hours, setting
temperature will decrease 2 , then the unit will run at this setting temperature.
ƔSleep 2 is sleep mode 2, that is air conditioner will run according to the presetting a
group of sleep temperature curve.
ƔSleep 3-the sleep curve setting under Sleep mode by DIY;
(1)Under Sleep 3 mode, press “Turbo” button for a long time, remote controller enters
into user individuation sleep setting status, at this time, the time of remote controller
will display “1hour”, the setting temperature “88” will display the corresponding temp-
erature of last setting sleep curve and blink (The first entering will display according to
the initial curve setting value of original factory);
(2)Adjust Ÿ and " "
Ÿ
button, could change the corresponding setting temperature,
after adjusted, press “Turbo” button for confirmation;
(3) At this time, 1hour will be automatically increased at the timer postion on the remote
control, (that are "2hours" or "3hours" or "8hours"), the place of setting temperature "88"
will display the corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours temperature setting finished,
sleep,curve setting finished, at this time, the remote controller will resume the original
timer display; temperature display will resume to original setting temperature.
Ɣ Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep
curve,
enter into user individuation sleep setting status, but do not change the tempera-
ture, press “Turbo” button directly for confirmation. Note: In the above presetting or
enquiry procedure, if continuously within 10s, there is no button pressed, the sleep
curve setting within 10s, there is no button pressed, the sleep curve setting status will
be automatically quit and resume to display the original displaying. In the presetting or
8SLEEP button
ƔPress this button, can select Sleep 1 ( ), Sleep 2 ( ), Sleep 3 ( ) and cancel
Ɣ
Ɣ
ǃǃ
" may not be available. When air conditioner receives this signal, the
air conditioner will blow fan automatically.
Press this button continuously more than 2s, the main unit will swing back an
forth from up to down, and then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immediately.
Under swing up and down mode, when the status is switched from off to , if
press this button again 2s later, status will switch to off status directly; if press
this button again within 2s, the change of swing status will also depend on the
circulation sequence stated above.
Note:
Ɣ

13
Introduction for buttons on remote controller
Note:
ƔUnder on and off status, you can set TIMER OFF or TIMER ON simultaneously.
ƔBefore setting TIMER ON or TIMER OFF, please adjust the clock time.
ƔAfter starting up TIMER ON or TIMER OFF, set the constant circulating valid.
After that, air conditioner will be turned on or turned off according to setting time.
ON/OFF button has no effect on setting. If you don’t need this function, please
use remote controller to cancel it.
the remote controller near the object of high temperature or low temperature in
order to avoid detecting inaccurate ambient temperature. When I FEEL function
is turned on, the remote controller should be put within the area where indoor
unit can receive the signal sent by the remote controller.
ƔTIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, " "
LFRQGLVDSSHDUVDQGWKHZRUG21RQUHPRWHFRQWUROOHUEOLQNV3UHVVŸRU
Ÿ
" " button to adjust TIMER ON setting.$IWHUHDFKSUHVVLQJŸRUEXWWRQ
Ÿ
7,0(521VHWWLQJZLOOLQFUHDVHRUGHFUHDVHPLQ+ROGŸRUEXWWRQV
Ÿ
later, the time will change quickly until reaching your required time.
Press "TIMER ON" to confirm it. The word "ON" will stop blinking. " " icon
resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is
started up, press "TIMER ON" button to cancel it.
ƔTIMER OFF button
"TIMER OFF" button can set the time for timer off.After pressing this button," "
icon disappears and the word "OFF" on UHPRWHFRQWUROOHUEOLQNV3UHVVŸRU
Ÿ
" " button to adjust TIMER OFF setting.$IWHUHDFKSUHVVLQJŸRUEXWWRQ
Ÿ
7,0(52))VHWWLQJZLOOLQFUHDVHRUGHFUHDVHPLQ+ROGŸRUEXWWRQV
Ÿ
later, the time will change quickly until reaching your required time.
Press "TIMER OFF" word "OFF" will stop blinking. " " icon resumes displaying.
Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press
"TIMER OFF" button to cancel it.
10 TIMER ON / TIMER OFF button
11 CLOCK button
Press this button to set clock time. " " icon on remote controller will blink. Press
9I FEEL button
Press this button to start I FEEL function and " " will be displayed on the remote
controller. After this function is set, the remote controller will send the detected
ambient temperature to the controller and the unit will automatically adjust the
indoor temperature according to the detected temperature. Press this button again
to close I FEEL function and " " will disappear.
ƔPlease put the remote controller near user when this function is set. Do not put
enquiry procedure, press
"ON/OFF" button, "Mode" button, "Timer" button or "Sleep"
button, the sleep curve setting or enquiry status will quit similarly.

14
14 LIGHT button
Press this button to turn off display light on indoor unit. " " icon on remote
controller disappears. Press this button again to turn on display light. " " icon is
displayed.
Introduction for buttons on remote controller
15 button
Press this button to achieve the on and off of healthy and scavenging functions in
operation status. Press this button for the first time to start scavenging function;
13 WiFi button
12 QUIET button
Press this button, the Quiet status is under the Auto Quiet mode (display " " and
"AUTO" signal ) and Quiet mode (display " " singal) and Quiet OFF (there is no
signal of " " displayed), after powered on, the Quiet OFF is defaulted.
Note:
Ɣ The Quiet function can be set up in all modes; Under the Quiet mode, the fan
speed is not available.
Ɣ
Ɣ
The Quiet function is only available for some models.
When quiet function is selected
Under cooling mode: indoor fan operates at notch 4 speed. 10 minutes later or
ZKHQLQGRRUDPELHQWWHPSHUDWXUHƇLQGRRUIDQZLOORSHUDWHDWQRWFKVSHHG
or quiet mode according to the comparison between indoor ambinet temperature
and set temperature.
Under heating mode: indoor fan operates at notch 3 speed or quiet mode according
to the comparison between indoor ambient temperature and set temperature.
Under dry, fan mode: indoor fan operates at quiet mode.
Under auto mode: the indoor fan operates at the auto quiet mode according to
actual cooling, heating or fan mode.
ƔThis function is only available for some models.
Press " WiFi " button to turn on or turn off WiFi function. When WiFi function is
turned on, the " WiFi " icon will be displayed on remote controller; Under status
of remote controller off, press "MODE" and "WiFi" buttons simultaneously for 1s,
WiFi module will restore to factory default setting.
Note:
Ɣ &ORFNWLPHDGRSWVKRXUPRGH
ƔThe interval between two operation can¶WH[FHHGVV2WKHUZLVHUHPRWHFRQWUR
ller will quit setting status. Operation for TIMER ON/TIMER OFF is the same.
clock time will increase or decrease 1 minXWH,IKROGŸRUEXWWRQVODWHU
Ÿ
,
time will change quickly. Release this button when reaching your required time.
Press "CLOCK" button to confirm the time. " " icon stops blinking.
Ÿ
ŸRUEXWWRQZLWKLQVWRVHWFORFNWLmH(DFKSUHVVLQJRIŸRUEXWWRQ
Ÿ

15
Function introduction for combination buttons
Energy-saving function
Under cooling mode, press "TEMP" and "CLOCK" buttons simultaneously to
start up or turn off energy-saving function. When energy-saving function is started
up, "SE" will be shown on remote controller, and air conditioner will adjust the set
temperature automatically according to ex-factory setting to reach to the best
energy-saving effect. Press "TEMP" and "CLOCK" buttons simultaneously again to
exit energy-saving function.
Note:
Under energy-saving function, fan speed is defaulted at auto speed and it can’tƔbe adjusted.
16 TEMP button
By pressing this button, you can see indoor set temperature, indoor ambient temp-
erature or outdoor ambient temperature on indoor unit’s display. The setting on
remote controlleris selected circularly as below:
no display
ƔWhen selecting " " or no display with remote controller, temperature indicator
on indoor unit displays set temperature.
ƔWhen selecting " " with remote controller, temperature indicator on indoor unit
displays indoor ambient temperature.
ƔWhen selecting " " with remote controller, temperature indicator on indoor unit
displays outdoor ambient temperature.
Note:
Ɣ Outdoor temperature display is not available for some models. At that time, indoor
unit receives " " signal, while it displays indoor set temperature.
ƔIts defaulted to display set temperature when turning on the unit.There is no
display in the remote controller.
ƔOnly for the models whose indoor unit has dual-8 display.
ƔWhen selecting displaying of indoor or outdoor ambient temperature, indoor
temperature indicator displays corresponding temperature and automatically turn
WRGLVSOD\VHWWHPSHUDWXUHDIWHUWKUHHRU¿YHVHFRQGV
LCD displays " ". Press the button for the second time to start healthy and
scavenging functions simultaneously; LCD displays " " and " " . Press this
button for the third time to quit healthy and scavenging functions simultaneously.
Press the button for the fourth time to start healthy function; LCD display " " .
Press this button again to repeat the operation above.
Ɣ This function is applicable to partial of models.
Introduction for buttons on remote controller


Function introduction for combination buttons
Child lock function
3UHVVŸDQGVLPXOWDQHRXVO\WRWXUQRQRUWXUQRIIFKLOGORFNIXQFWLRQ:KHQ
FKLOGORFNIXQFWLRQLVRQLFRQLVGLVSOD\HGRQUHPRWHFRQWUROOHU,I\RXRSHUDWH
WKHUHPRWHFRQWUROOHUWKHLFRQZLOOEOLQNWKUHHWLPHVZLWKRXWVHQGLQJVLJQDOWR
WKHXQLW
Ÿ
Temperature display switchover function
8QGHU2))VWDWXVSUHVVDQG02'(EXWWRQVVLPXOWDQHRXVO\WRVZLWFKWHPS
HUDWXUHGLVSOD\EHWZHHQćDQG
Ÿ
Note:
Ɣ 8QGHUćKHDWLQJIXQFWLRQIDQVSHHGLVGHIDXOWHGDWDXWRVSHHGDQGLWFDQ¶WEH
DGMXVWHG
Ɣ 8QGHUćKHDWLQJIXQFWLRQVHWWHPSHUDWXUHFDQ¶WEHDGMXVWHG3UHVV
 785%2 
EXWWRQDQGWKHUHPRWHFRQWUROOHUZRQ¶WVHQGVLJQDO
Ɣ 6OHHSIXQFWLRQDQGćKHDWLQJIXQFWLRQFDQ¶WRSHUDWHDWWKHVDPHWLPH,Ić
KHDWLQJIXQFWLRQKDVEHHQVHWXQGHUFRROLQJPRGHSUHVVVOHHSEXWWRQZLOOFDQFHO
ćKHDWLQJIXQFWLRQ,IVOHHSIXQFWLRQKDVEHHQVHWXQGHUFRROLQJPRGHVWDUWXS
WKHćKHDWLQJIXQFWLRQZLOOFDQFHOVOHHSIXQFWLRQ
Ɣ 8QGHUWHPSHUDWXUHGLVSOD\WKHUHPRWHFRQWUROOHUZLOOGLVSOD\ KHDWLQJ
8ćheating function
8QGHUKHDWLQJPRGHSUHVV7(03DQG&/2&.EXWWRQVVLPXOWDQHRXVO\WRVWDUW
XSRUWXUQRII
ć
KHDWLQJIXQFWLRQ:KHQWKLVIXQFWLRQLVVWDUWHGXSDQG
ć
 
ZLOOEHVKRZQRQUHPRWHFRQWUROOHUDQGWKHDLUFRQGLWLRQHUNHHSWKHKHDWLQJVWDWXV 
DWć3UHVV7(03DQG&/2&.EXWWRQVVLPXOWDQHRXVO\DJDLQWRH[LWć
KHDWLQJIXQFWLRQ
Ɣ 8QGHUHQHUJ\VDYLQJIXQFWLRQVHWWHPSHUDWXUHFDQ¶WEHDGMXVWHG3UHVV785%2
EXWWRQDQGWKHUHPRWHFRQWUROOHUZRQ¶WVHQGVLJQDO
Ɣ 6OHHSIXQFWLRQDQGHQHUJ\VDYLQJIXQFWLRQFDQ¶WRSHUDWHDWWKHVDPHWLPH,I
HQHUJ\VDYLQJIXQFWLRQKDVEHHQVHWXQGHUFRROLQJPRGHSUHVVVOHHSEXWWRQZLOO
FDQFHOHQHUJ\VDYLQJIXQFWLRQ,IVOHHSIXQFWLRQKDVEHHQVHWXQGHUFRROLQJ
PRGHVWDUWXSWKHHQHUJ\VDYLQJIXQFWLRQZLOOFDQFHOVOHHSIXQFWLRQ