Green motion SMART ONE Guide

SMART ONE
TECHNICAL DOCUMENTATION
NON-CONTRACTUAL PICTURES | DOC. VERSION 26112020
Opening the charging station and any changes to the configuration must be done by a qualified electrician and must comply with local
regulations and laws for safety in the use of electricity. Failure to comply with the regulations in this manual will result in the end the
warranty period.

SMART ONE – TECHNICAL DOCUMENTATION Page 2
CONTENT
1. INTRODUCTION 3
1.1 TECHNICAL SPECIFICATIONS 3
1.2 DIMENSIONS AND WEIGHTS 3
2. INSTALLATION 4
2.1 MOUNTING 4
2.2 ELECTRICAL CONNECTION 5
2.3 CONNECTION TO THE LAN NETWORK 6
2.4 CAN CONNECTION 7
2.5 CONNECTION OF THE SMART ONE WITH THE GREEN MOTION PRIVATE ONE CHARGING STATIONS 8
2.6 SUPPORT 10
3. ANNEXES 11
3.1 SMART ONE HOUSING DIMENSIONS (MM) 11

SMART ONE – TECHNICAL DOCUMENTATION Page 3
1 INTRODUCTION
1.1 Technical Specifications
POWER INPUT
SMART POWER MANAGEMENT SYSTEM
Input voltage
1 x 230 VAC 50 Hz
Input current
1 x 8 Arms
Standby-consumption
<6 W
CHARGING STATIONS CONTROL
Types
Slow-charge stations as well as multi-standard Combo and CHAdeMO quick-
charge stations
Smart control
Control up to 100 charging stations
Power management
Dynamic load balancing
Station communication
RS 485, CAN, Ethernet cable
Maximale line length
200 meters
USER INTERFACE & CONTROL
Mobile phone app
iOS and Android
Control of access
RFID, App,Scan & Charge
Network interface
Ethernet cable (RJ45) ; 3G/4G
Remote Management
Management console with consumption statistics, management of users and
status of stations in real-time
ENVIRONMENTAL
Operating temperature
–25 °C to 45 °C
Altitude
Up to 2000 m (6500 ft.)
Setting
Wall ; indoor or outdoor
Humidity
<95% relative humidity
MECHANICAL
Dimensions
192 x 225 x 122 mm
Weight
2 kg
Housing material
Polycarbonate glass fibre reinforced
REGULATION
Conformity
IEC 61851-1
Protection rating
IP55
Communication protocol
OCPP 1.6J
1.2 Dimensions and weights
Width
192 mm
Height
225 mm
Depth
122 mm
Weight
2 Kg

SMART ONE – TECHNICAL DOCUMENTATION Page 4
2 INSTALLATION
2.1 Mounting
2.1.1 Mounting
Recommended mounting height: 1500 mm
Fixing with 4 screws according to the following diagram:
Screw through the SMART ONE terminal and, if necessary, use the supplied seals to ensure tightness.

SMART ONE – TECHNICAL DOCUMENTATION Page 5
2.2 Electrical connection
The electrical installation of the SMART ONE must be performed by a qualified electrician.
The SMART ONE should be connected to the single-phase 230 VAC on the terminals N-L-PE. Maximum
power consumption of the SMART ONE is 6 W.
Electric shock hazard! Please make sure that the main power supply is turned off before
trying to connect the power to the SMART ONE. In any case, working under voltage shall be
avoided.

SMART ONE – TECHNICAL DOCUMENTATION Page 6
2.3 Connection to the LAN network
The network cable is introduced below the SMART ONE and it should be connected onto the RJ45
socket, which is located on the electronics board. For edgewise connection there’s an optional adapter
available. If it used, ensure that the adaptor is not touching live parts on the electronics board.
There are two possible means of internet connection, by UMTS 3G or by RJ45 cable.
For UTMS 3G/4G connection, the modem is installed by Green Motion when ordering the charging
station. 3G/4G network coverage must be checked before installation of the SMART ONE is carried out.
Green Motion does not recommend using the 3G/4G network in an underground car parking or in areas
that have poor mobile network services.
Green Motion can also install a fiber optic SC port to ethernet RJ45 converter (multimode type or single
mode type). (Quote on demand).
The charging station and the payment system are configured in DHCP. It is not possible to assign fixed IP
addresses to the equipment. If it is essential to use a fixed IP address, Green Motion can install an
additional router in the charging station.
Green Motion charging stations communicate to the Green Motion server IP address 108.129.36.195 on
the TCP 83 port number.
Incoming data (NAT/PAT) is not necessary.

SMART ONE – TECHNICAL DOCUMENTATION Page 7
2.4 CAN connection
The connection between the SMART ONE and the controlled charging stations is made via a CAN bus by
a twisted shielded pair cable. The CAN bus cable is connected onto the terminals CAN+ and CAN-. Both
CAN+ and CAN- terminals must be used if the SMART ONE is located in the middle of the CAN bus.
The maximum CAN bus line length is 200 meters.
The CAN bus must have a termination resistance of 120 ohm at each end:
The termination resistance can be activated on the SMART ONE by putting a plug on “J15” and on “J14”.
SMART
ONE
Control
terminal
Control
terminal

SMART ONE – TECHNICAL DOCUMENTATION Page 8
2.5 Connection of the SMART ONE with the Green Motion PRIVATE ONE charging
stations
The connection between the SMART ONE and the PRIVATE ONE charging stations is made via a CAN
bus by a twisted pair cable (DATA Dca-flex C 2x2x0.75).
The maximum CAN bus line length is 200 meters.
The SMART ONE can be located at any point along the BUS. The termination resistance must be
activated if it is located at one end of the CAN bus.

SMART ONE – TECHNICAL DOCUMENTATION Page 9
The termination resistance can be activated on the SMART ONE by putting a plug on “J15” and on “J14”.
On the PRIVATE ONE charging station, the CAN bus cables is connected onto the terminals 17 (CAN+)
and 18 (CAN-):
This schema may vary according to the controlled P1 charging station.

SMART ONE – TECHNICAL DOCUMENTATION Page 10
There must be a shielded twisted pair cable (e.g., As DATA Dca-flex C 2x2x0.75 shielded) are used. The
cable must not be longer than 2 cm. The shield and the cables that are not used for the CAN, must be
connected to the ground terminal or GND. It is forbidden to use the free cables for other functions.
The termination resistance can be activated by activating the upper DIPSwitch number 2:
Deactivated: Activated:
On the SMART ONE, the CAN bus cables is connected onto the terminals CAN- and CAN+:
2.6 Support
Green Motion telephone support is available Monday to Friday from 08:00 to 12:00 and from 13:00 to
17:00 (16:00 on Friday) CET.
Email : [email protected]
Tel: [phone]

SMART ONE – TECHNICAL DOCUMENTATION Page 11
3 ANNEXES
3.1 SMART ONE housing dimensions (mm)

SMART ONE – TECHNICAL DOCUMENTATION Page 12
Green Motion Ltd
Chemin de Maillefer 61
1052 Le Mont-sur-Lausanne
Switzerland
GreenMotionEV.com
[email protected]
[phone]