Grizzly G0508 User manual
COPYRIGHT © DECEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TS10264 PRINTED IN TAIWAN
The requirements for rewiring this dust collector for 440V operation have changed slightly from when the
manual was originally written. Refer to the photo and illustration below for detailed instructions for rewiring
the motor. All other 440V conversion instructions are the same (refer to Rewiring to 440V on Page 9 of
the manual).
Before rewiring your dust collector for 440V operation, you MUST read and understand this manual update
AND the original manual to reduce the risk of injury from improper use or setup.
If you need additional help with any of these procedures, contact our Tech Support at (570) 546-9663 or by
email at [email protected].
MODEL G0508
10 HP INDUSTRIAL
DUST COLLECTOR
MANUAL UPDATE
Figure 1. Wiring diagram on
the inside of the motor wiring
cover.
MODEL G0508
10 HP INDUSTRIAL
DUST COLLECTOR
OWNER'S MANUAL
COPYRIGHT © NOVEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TS8335 PRINTED IN TAIWAN
Table of Contents
INTRODUCTION ............................................................................................................................... 2
Foreword .................................................................................................................................... 2
Contact Info ................................................................................................................................ 2
Machine Data Sheet ................................................................................................................... 3
Identification ............................................................................................................................... 5
SECTION 1: SAFETY ....................................................................................................................... 6
Safety Instructions for Machinery ............................................................................................... 7
Additional Safety for Dust Collectors ......................................................................................... 8
SECTION 2: CIRCUIT REQUIREMENTS ........................................................................................ 9
220/440V 3-Phase ..................................................................................................................... 9
Grounding ................................................................................................................................... 9
Rewiring to 440V ........................................................................................................................ 9
SECTION 3: SET UP ...................................................................................................................... 10
Set Up Safety ........................................................................................................................... 10
Items Needed for Setup ........................................................................................................... 10
Unpacking ................................................................................................................................ 10
Inventory ................................................................................................................................... 11
Site Considerations .................................................................................................................. 12
Assembly .................................................................................................................................. 12
Test Run ................................................................................................................................... 15
SECTION 4: DESIGNING THE SYSTEM ....................................................................................... 17
General ..................................................................................................................................... 17
Duct Material ............................................................................................................................ 17
System Design ......................................................................................................................... 19
System Grounding ................................................................................................................... 23
SECTION 5: ACCESSORIES ......................................................................................................... 25
SECTION 6: OPERATIONS ........................................................................................................... 28
General ..................................................................................................................................... 28
SECTION 7: MAINTENANCE ........................................................................................................ 29
Schedule .................................................................................................................................. 29
Lubrication ................................................................................................................................ 29
Bag Cleaning ............................................................................................................................ 29
SECTION 8: SERVICE ................................................................................................................... 30
About Service ........................................................................................................................... 30
Troubleshooting ........................................................................................................................ 30
Electrical Components ............................................................................................................. 31
Wiring Diagram ........................................................................................................................ 32
Parts Breakdown ...................................................................................................................... 33
Label Placement ...................................................................................................................... 35
WARRANTY AND RETURNS ........................................................................................................ 36
-2- G0508 10 HP Industrial Dust Collector
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
C/O Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
E-Mail: [email protected]
We stand behind our machines. If you have any
service questions or parts requests, please call or
write us at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
Web Site: http://www.grizzly.com
Foreword
INTRODUCTION
Contact Info
We are proud to offer the Model G0508 10 HP
Industrial Dust Collector. This machine is part
of a growing Grizzly family of fine woodworking
machinery. When used according to the guide-
lines set forth in this manual, you can expect
years of trouble-free, enjoyable operation and
proof of Grizzly’s commitment to customer satis-
faction.
We are pleased to provide this manual with the
Model G0508; it will guide you through assembly,
safety considerations, and general operating pro-
cedures. It represents our effort to produce the
best documentation possible.
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G0508 as supplied when the manual was pre-
pared. However, owing to Grizzly’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
For your convenience, we always keep current
Grizzly manuals available on our website at www.
grizzly.com. Any updates to your machine will be
reflected in these manuals as soon as they are
complete. Visit our site often to check for the lat-
est updates to this manual!
G0508 10 HP Industrial Dust Collector -3-
Machine Data Sheet
MODEL G0508 10 HP INDUSTRIAL DUST COLLECTOR
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
MACHINE DATA
SHEET
Product Dimensions:
Weight .............................................................................................................................................................515 lbs.
Length/Width/Height .........................................................................................................................61 x 61 x 134 in.
Foot Print (Length/Width) .............................................................................................................................61 x 61 in.
Shipping Dimensions:
Type .......................................................................................................................................Cardboard/Wood Frame
Content ............................................................................................................................................................Machine
Weight ..............................................................................................................................................................560 lbs.
Length/Width/Height .............................................................................................................................47 x 53 x 31 in.
Electrical:
Switch ............................................................................................................. Magnetic with Thermal Overload Relay
Switch Voltage ..................................................................................................................................................... 220V
Cord Length ......................................................................................................................................................... 12 ft.
Cord Gauge .................................................................................................................................................. 10 gauge
Recommended Breaker Size ........................................................................................................................... 40 amp
Plug ..........................................................................................................................................................................No
Conversion To 440V ............................................................................................................... Part Number P0508037
Phase Converter .....................................................................................................................................Model G7979
Motors:
Type .......................................................................................................................................... TEFC Induction
Horsepower .............................................................................................................................................. 10 HP
Voltage ................................................................................................................................................220/440V
Prewired ..................................................................................................................................................... 220V
Phase ........................................................................................................................................................ Three
Amps ....................................................................................................................................................... 26/13A
Speed ................................................................................................................................................ 3450 RPM
Cycle .........................................................................................................................................................60 Hz
Number Of Speeds .......................................................................................................................................... 1
Power Transfer .................................................................................................................................Direct Drive
Bearings ...................................................................................................................... Shielded and Lubricated
Main Specifications:
Air Suction Capacity ..........................................................................................................................6700 CFM
Maximum Static Pressure Rating ..............................................................................................................21 in.
Main Inlet Size .............................................................................................................................................9 in.
Manifold Included ..........................................................................................................................................Yes
Manifold Inlets .................................................................................................................................................. 5
Manifold Inlet Size .......................................................................................................................................4 in.
Machine Collection Capacity ...........................................................................................................8 Machines
Maximum Material Collection Capacity ............................................................................................. 64.8 cu. ft.
Upper Bag Filtration ...........................................................................................................................2.5 micron
-4- G0508 10 HP Industrial Dust Collector
Bag Information
Number of Upper Bags .................................................................................................................................... 4
Upper Bag Capacity .......................................................................................................................... 17.8 cu. ft.
Lower Bag Capacity .......................................................................................................................... 13.7 cu. ft.
Number of Lower Bags .................................................................................................................................... 4
Upper Bags Total Area ......................................................................................................................... 71 cu. ft.
Lower Bags Total Area ...................................................................................................................... 54.8 cu. ft.
Upper Bag Diameter ........................................................................................................................... 23-5/8 in.
Upper Bag Length ......................................................................................................................................70 in.
Lower Bag Diameter ........................................................................................................................... 23-5/8 in.
Lower Bag Length ......................................................................................................................................54 in.
Impeller Information
Impeller Type ..................................................................................................................................... Radial Fin
Impeller Size ....................................................................................................................................... 14-3/4 in.
Impeller Blade Thickness ..........................................................................................................................1/4 in.
Construction
Upper Bag Material ...................................................................................................................... Woven Fabric
Lower Bag Material ..................................................................................................................................Plastic
Base Construction ............................................................................................... Pre-Formed Steel on Casters
Frame Construction ......................................................................................................................Formed Steel
Caster Construction .................................................................................................................................Plastic
Impeller Construction ....................................................................................................Balanced Welded Steel
Paint ...........................................................................................................................................Powder Coated
Other Specifications:
ISO Factory ................................................................................................................................................... ISO 9001
Country Of Origin .............................................................................................................................................. Taiwan
Warranty ............................................................................................................................................................. 1 Year
Serial Number Location .......................................................................................................... Data Label on Machine
Assembly Time ........................................................................................................................................... 1-1/2 hours
Features:
10 HP Industrial Motor
4 Heavy Duty Plastic Collection Bags
4 filtration Bags
Includes Steel Base with Casters
G0508 10 HP Industrial Dust Collector -5-
Identification
A. Upper Filter Bag
B. Collector
C. Lower Collection Bag
D. Caster
E. Upper Bag Hanger Assembly
F. Inlet
G. ON/OFF Power Switch
H. Motor
I. Base
Figure 1. Dust collector, front view.
A
B
C
D
E
F
G
H
I
-6- G0508 10 HP Industrial Dust Collector
G0508 10 HP Industrial Dust Collector -7-
Safety Instructions for Machinery
-8- G0508 10 HP Industrial Dust Collector
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machines there is danger associated
with this machine. Accidents are frequently
caused by lack of familiarity or failure to pay
attention. Use this machine with respect
and caution to lessen the possibility of
operator injury. If normal safety precautions
are overlooked or ignored, serious personal
injury may occur.
Additional Safety for Dust Collectors
6. AVOIDING FIRES. Do not allow steel to
strike against impeller—this may produce
a spark. Sparks can smolder in wood dust
for a long time before fire or flame is detect-
ed. If metal contacts metal during opera-
tion, immediately turn off the dust collector,
unplug the power cord from the outlet or flip
the disconnect switch and wait for all moving
parts to stop. Remove collection bags and
empty the dust into an approved air tight
metal container in case of spark. Remedy
the metal to metal contact problem before
resuming operation.
7. OPERATIONAL QUESTIONS. If at any time
you are experiencing difficulties perform-
ing the intended operation, stop using the
machine! Then contact our Tech Support
or ask a qualified expert how the operation
should be performed.
8. CLEANING AIR. Do not confuse this dust
collector with an air cleaner. This dust col-
lector is only designed to collect dust from
a machine, not clean dust suspended in the
air.
9. EMPTYING DUST. When emptying dust
from the collection bags or drum, wear a
respirator and safety glasses. Empty dust
into an approved container and dispose of
properly.
1. MACHINE USE. Do not use this dust col-
lector to pick up liquids and metal scrap
including, but not limited to, nails and filings.
Also, do not pick up material which cannot
safely pass through the impeller such as
solid wood scraps.
2. KEEPING FINGERS SAFE. Do not place
your hands or tools near the open inlet dur-
ing operation for any reason including, but
not limited to, unclogging material and test-
ing suction. The impeller could cause seri-
ous damage to body parts if touched while
spinning.
3. SAFE SERVICING. Disconnect power and
allow impeller to come to a complete stop
before servicing or working on the dust col-
lector ducting system.
4. SUSPENDED DUST PARTICLES AND
IGNITION SOURCES. Do not operate the
dust collector in areas where explosion risks
would be high if dust were dispersed into the
area. Areas of high risk include, but are not
limited to, areas near pilot lights and/or open
flames.
5. DUST HAZARD. Be aware that certain
woods may cause an allergic reaction in peo-
ple and animals, especially when exposed to
fine dust. Make sure you know what type of
wood dust you will be exposed to in case
there is a possibility of an allergic reaction.
Always wear an approved respirator during
and for a short time after machine opera-
tion!
G0508 10 HP Industrial Dust Collector -9-
Serious personal injury could occur if you
connect your machine to the power source
before you have completed the set up pro-
cess. DO NOT connect the machine to the
power source until instructed to do so.
220/440V 3-Phase
SECTION 2: CIRCUIT REQUIREMENTS
The Model G0508 can be rewired for 440V opera-
tion. This rewiring job consists of disconnecting
the dust collector from the power source, chang-
ing the magnetic switch, and rewiring the motor.
The necessary magnetic switch for this procedure
can be purchased by calling our customer service
number at (800) 523-4777 and ordering part num-
ber P0508037.
This procedure takes moderate electrical skill and
the rewiring job must be inspected by a qualified
electrician before the dust collector is connected
to the power source.
Rewiring to 440V
Amperage Draw
The Model G0508 features a 220/440V motor
that is prewired for 220V and draws the following
amps under maximum load:
Motor Draw at 220V ............................. 26 Amps
Motor Draw at 440V ............................. 13 Amps
Circuit Requirements
We recommend connecting your machine to a
dedicated and grounded circuit that is rated for
the amperage given below. Never replace a circuit
breaker on an existing circuit with one of higher
amperage without consulting a qualified electri-
cian to ensure compliance with wiring codes. If
you are unsure about the wiring codes in your
area or you plan to connect your machine to a
shared circuit, consult a qualified electrician.
220V Circuit ........................................... 40 Amps
440V Circuit ........................................... 20 Amps
Connection to Power
Have a qualified electrician hardwire this machine
to a dedicated locking shut-off switch that is con-
nected to the main power source.
In the event of an electrical short, grounding
reduces the risk of electric shock. The grounding
wire in the power cord must be properly connected
to the grounding prong on the plug; likewise, the
outlet must be properly installed and grounded.
All electrical connections must be made in accor-
dance with local codes and ordinances.
Improper connections of the electrical-grounding
conductor increases the risk of electric shock.
Check with a qualified electrician or one of
our service personnel if you do not understand
the grounding instructions, or if you doubt the
machine is properly grounded.
Grounding
Electrocution or fire could
result if this machine is
not installed correctly or
the electrical installation
does not comply with local
and state codes. Ensure
compliance by using a
qualified electrician for the
electrical installation!
-10- G0508 10 HP Industrial Dust Collector
Wear safety glasses dur-
ing the entire set up pro-
cess!
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Set Up Safety
SECTION 3: SET UP
The Model G0508 is a
heavy machine. DO NOT
over-exert yourself while
unpacking or moving
your machine—get assis-
tance.
The Model G0508 was carefully packed when it
left our warehouse. If you discover the machine
is damaged after you have signed for delivery,
please immediately call Customer Service at
(570) 546-9663 for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, you should inventory the
contents.
Unpacking
The following items are needed to complete the
set up process, but are not included with your
machine:
Description Qty
• Assistant ........................................1 or more
• Safety Glasses (for each person) .............. 1
• Gloves (for each person) ............................ 1
• Phillips Head Screwdriver .......................... 1
• Wrench 10mm ............................................ 1
• Wrenches 12mm ........................................ 2
• Ladder (for hanging upper bag) ................. 1
Items Needed for
Setup
Some metal parts may
have sharp edges on
them after they are
formed. Please examine
the edges of all metal
parts before handling
them. Failure to do so
could result in injury. Turn OFF the power at
the power disconnect
and do NOT turn ON
until instructed to do so.
Failure to heed this warn-
ing could result in seri-
ous personal injury or
death.
G0508 10 HP Industrial Dust Collector -11-
Inventory
After all the parts have been removed from the
two boxes, you should have the following items:
Contents (Figure 2–4) Qty
A. Main Housing with Motor ............................ 1
B. Inlet ............................................................. 1
C. Collectors ................................................... 4
D. Supporting Legs ......................................... 4
E. Base ........................................................... 1
F. Hanger Supports ........................................ 4
G. Hangers ...................................................... 4
H. Upper Filter Bags (fabric) ........................... 4
I. Lower Collection Bags (plastic) .................. 4
J. Casters ....................................................... 4
K. Rubber Gaskets ......................................... 4
L. Bag Clamps ................................................ 8
M. Hardware Bag (not shown) ......................... 1
— Combo Wrench 10/12mm ...................... 1
— Phillips Head Screw M6-1.0 x 10 ........... 1
— Flange Bolts 1⁄4"-20 x 1⁄2" ...................... 12
— Flange Bolts 5⁄16"-18 x 1⁄2" ..................... 32
— Flat Washers 5⁄16" ................................. 64
— Hex Bolts 5⁄16"-18 x 1" ........................... 32
— Hex Nuts 5⁄16"-18 .................................. 32
Figure 2. Model G0508 Inventory (A–D).
In the event that any nonproprietary parts are
missing (e.g., a nut or a washer), we would be
glad to replace them, or for the sake of expedi-
ency, replacements can be obtained at your local
hardware store.
NOTICE
Some hardware/fasteners listed in the inven-
tory may arrive pre-installed on the machine.
Check these locations before assuming that
any items from the inventory list are miss-
ing.
A
B
C
D
E
F
G
H
I
Figure 3. Model G0508 Inventory (E–I).
JK
L
Figure 4. Model G0508 Inventory (J–L).
-12- G0508 10 HP Industrial Dust Collector
Figure 6. Caster mounted on base.
Caster Mounting
Caster
Floor Load
Refer to the Machine Data Sheet on Page 3 for
the weight and footprint specifications of your
machine. Some floors may require additional
reinforcement to support both the machine and
operator.
Placement Location
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
your new machine. See Figure 5 for the minimum
working clearances.
Site Considerations
Figure 5. Model G0508 illustrated top view and
suggested clearances.
Assembly
To the dust collector system:
1. Place the base upside down on the floor.
2. Attach the casters with the (16) 5⁄16"-18 x 1⁄2"
flange bolts (see Figure 6).
3. With assistance, place the main housing on
the floor so that the motor is pointing up.
4. Place the end of the supporting leg with the
threaded holes on the inside of the housing
bracket (see Figure 7).
Figure 7. Supporting leg mounted to main
housing.
Flange Bolts
G0508 10 HP Industrial Dust Collector -13-
5. Attach the supporting legs to the housing
bracket with 5⁄16"-18 x 1⁄2" flange bolts.
6. Position the base on top of the supporting
legs (see Figure 8).
Figure 8. Base attached to supporting leg.
Flange Bolts
10. With assistance, position and hold the collec-
tor so the holes in the collector flange match
with those of the rubber gasket and main
housing.
11. Insert and hand tighten one 5⁄16"-18 x 1"
flange bolt, two 5⁄16" flat washers, and one 5⁄16"-
18 hex nut in all eight holes.
12. Tighten the eight flange bolts and nuts in a
alternating fashion so that the rubber gasket
is evenly compressed without deformation.
13. Repeat Steps 10–13 for the remaining col-
lectors.
14. Place the inlet on the top center circular
flange of the main housing (see Figure 10).
Figure 10. Inlet mounted on main housing.
Screw
7. Fasten the supporting legs to the base with
5⁄16"-18 x 1⁄2" flange bolts.
8. With assistance, turn the entire assembly
over so that the casters rest on the floor.
9. Position and hold the rubber gasket against
the square opening in the main housing (see
Figure 9).
Figure 9. Collector mounted to main housing.
Mounting Bolts
Rubber Gasket
Collector
Main Housing
15. Rotate the inlet so the hole in the inlet aligns
with the hole in the housing flange.
16. Use the M6-1 x 10 Phillips head screw to fas-
ten the inlet securely to the housing flange.
-14- G0508 10 HP Industrial Dust Collector
17. Slide the hanger into the hanger support,
aligning the two holes on each part.
18. Secure this hanger assembly with two 1⁄4"-20
x 1⁄2" flange bolts (see Figure 11).
Figure 11. Hanger attached to hanger support.
Hanger
Hanger Support
19. Mount the hanger assembly on the protruding
rod on the collector as shown in Figure 12.
Figure 12. Hanger assembly mounted onto
collector.
Hanger
Assembly
20. Align the hanger assembly so that the hook
at the top is directly over the center of the col-
lector.
21. Secure the hanger assembly with one 1⁄4"-20
x 1⁄2" flange bolt (see Figure 12).
22. Repeat Steps 18–22 for the remaining hang-
er assemblies.
23. Place the loop at the top of the upper col-
lection bag over the top hook of the hanger
assembly (see Figure 13).
Figure 13. Upper filter bag mounted on hanger
assembly.
Bag Loop
Hanger
Assembly
24. Thread the bag clamp into and around the
bottom seam of the upper collection bag (see
Figure 14).
Flange
Bolt
G0508 10 HP Industrial Dust Collector -15-
25. Slip the bottom of the bag over the top lip of
the collector so that the bag clamp is com-
pletely over the lip as well.
26. Fasten the locking mechanism of the bag
clamp to secure the bag to the collector (see
Figure 14).
27. Slip the lower collection bag over the bottom
lip of the collector and position the bag evenly
around the collector.
28. Snag the bag on the hooks to hold the bag
in place until the bag clamp can be secured
(see Figure 15).
Figure 14. Upper filter bag secured to collector.
Bag Clamp
Figure 15. Bottom collection bag snagged on
collector hooks.
Collector Hook
29. Wrap the bag clamp around the collector and
position it between the bottom lip of the col-
lector and the hooks, fasten the bag clamp to
secure the bag to the collector (see Figure
16).
Figure 16. Lower collection bag secured to
collector.
Bag Clamp
-16- G0508 10 HP Industrial Dust Collector
Once assembly is complete, test run your machine
to make sure it runs properly.
To test run the dust collector:
1. Make sure you have read and understand all
of the safety instructions starting on Page 6
of this manual, and make sure the machine is
set up properly.
2. Connect the dust collector to the proper power
source (reference Circuit Requirements on
Page 9).
3. Clear away from the machine all tools and
objects used during the setup.
4. Turn the machine ON by pushing in the
GREEN button on the power switch.
5. Listen and watch for abnormal noises or
operation. The machine should run smoothly
with little or no vibration or rubbing noises.
— Strange or unusual noises MUST be inves-
tigated and corrected before operating the
machine further. Always disconnect the
machine from power before investigating
or correcting potential problems.
—If you cannot easily locate the source of a
potential problem, refer to Troubleshooting
on Page 30 or contact our Technical
Support at (570) 546-9663.
6. Turn OFF the machine by pushing in the RED
button on the power switch.
Test Run
Wear safety glasses
whenever starting or
using machine. Failure
to comply may result in
serious personal injury.
Keep loose clothing
rolled up and out of the
way of machinery and
keep hair pulled back.
Do NOT put hands or
small objects near inlet
openings during opera-
tion. Objects sucked
into the inlet will meet
with the impeller blade.
Failure to heed this
warning could result in
property damage or per-
sonal injury.
G0508 10 HP Industrial Dust Collector -17-
Duct Material
General
The Model G0508 can be operated as either a sta-
tionary or mobile unit. There are advantages and
disadvantages to both set-ups. The advantage of
the mobile system is eliminating the cost of many
ducts and fittings. On the other hand, the station-
ary system is more versatile and convenient.
The Model G0508 is designed to be a central
dust collector system. Locate the dust collector
in an out of the way location such as a corner or
separate room. The dust collector is capable of
collecting dust from up to eight machines running
simultaneously. The large suction capacity of the
Model G0508 allows great flexibility in planning
and designing of your dust collection duct layout.
Grizzly offers a complete line of dust collection
accessories for setting up a stationary system.
Additionally, Grizzly offers a complete guide book
titled Dust Collection Basics.
A 5-port inlet is included with the Model G0508
for quick and economical dust collection setup.
However, depending upon your system design
using this feature, bags may fill at different rates
requiring you to empty some bags more often
than others.
Whatever system you choose, always make sure
there are no open flames (including pilot lights) in
the same room as the dust collector; otherwise
you risk an explosion if dust is dispersed into the
air.
SECTION 4: DESIGNING THE
SYSTEM
You have many choices regarding main line and
branch line duct material. For best results, use
metal duct for the main line and branch lines, then
use a short lengths of flexible hose to connect
each machine to the branch lines.
Plastic duct is also a popular material for home
shops. However, be aware that there is a fire or
explosion hazard if plastic duct material is used
for dust collection without being grounded against
static electrical charge build-up. This topic will be
discussed later in this section. Another problem
with using plastic is that it is less efficient per foot
than metal.
Metal Duct
Advantages of metal duct is its conductivity and
that it does not contribute to static electrical
charge build-up. However, static charges are still
produced when dust particles strike other dust
particles as they move through the duct. Since
metal duct is a conductor, it can be grounded quite
easily to dissipate any static electrical charges.
Figure 17. Examples of metal pipe and
components.
Other manuals for G0508
1
Table of contents
Other Grizzly Dust Collector manuals
Grizzly
Grizzly G0850 User manual
Grizzly
Grizzly G1030 User manual
Grizzly
Grizzly G1028 User manual
Grizzly
Grizzly G1028Z/G1029 User manual
Grizzly
Grizzly G0637HEP User manual
Grizzly
Grizzly G0637 User manual
Grizzly
Grizzly G8027 User manual
Grizzly
Grizzly G0710 User manual
Grizzly
Grizzly G0441 Quick start guide
Grizzly
Grizzly G1032 User manual
Grizzly
Grizzly G1028Z User manual
Grizzly
Grizzly G0442 Quick start guide
Grizzly
Grizzly G0441 User manual
Grizzly
Grizzly G0562 User manual
Grizzly
Grizzly G0638 Quick start guide
Grizzly
Grizzly T31639 User manual
Grizzly
Grizzly G0548 User manual
Grizzly
Grizzly G1029Z User manual
Grizzly
Grizzly G0852 User manual
Grizzly
Grizzly G0562Z User manual
Popular Dust Collector manuals by other brands
Oneida Air Systems
Oneida Air Systems Supercell XSK000035 owner's manual
PuriSystems
PuriSystems PuriCare 500 user manual
Nederman
Nederman FlexPAK Standard Installation and service manual
Donaldson Torit
Donaldson Torit E-100 Installation and operation manual
Craftsman
Craftsman 315.22100 Operator's manual
RoboVent
RoboVent VENTBOSS G130 owner's manual
Conair
Conair Dust Collector Size 3 user guide
Dustless
Dustless DustBudiie 16008 quick start guide
Donaldson
Donaldson DFPRE 6L Series Installation, operation and maintenance manual
Holzmann
Holzmann ABS 850 user manual
Imperial Systems
Imperial Systems CMAXX Installation, operation & maintenance manual
Makita
Makita DX10 instruction manual