Grizzly H8094 User manual
Model H8094
21⁄2 Ton
Garage Jack
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR8825 PRINTED IN CHINA
Specifications
Maximum Lifting Capacity ................... 5000 Lbs.
Lifting Range .......................................51⁄4"–191⁄2"
Weight ..................................................... 62 Lbs.
If you need help with the Model H8094, call our
Technical Support line at: (570) 546-9663.
Failure to follow these instructions could
result in serious personal injury or death:
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle with appro-
priately rated support stands before
working under it.
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
5. Center the load on the jack to maintain
proper balance and stability.
6. DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
Figure 1. Jack controls.
Pump
Handle
Operation
Pump Handle (Figure 1): To raise the jack, rotate
the pump handle clockwise completely, then move
the pump handle up and down. To lower the jack,
slowly rotate the pump handle counterclockwise.
Maintenance
Keep the hydraulic rams clean and free of any
dust, dirt, or foreign debris. Abrasive material
stuck to the ram can damage the hydraulic seal
when the ram is retracted back into the jack.
Regularly wipe the hydraulic rams clean with a
lightly oiled rag.
The Model H8094 will require hydraulic fluid after
long-term use. This will be noticeable if the jack
will not reach its maximum height when pumped.
Only use a high quality hydraulic fluid.
To add hydraulic fluid:
1. Completely lower the jack.
2. Remove the fill plug shown in Figure 2.
Figure 2. Fill plug.
Bleeding the Air
If the jack becomes spongy or will not rise when
pumped, then air bubbles may be in the hydraulic
system.
To remove the air bubbles:
1. Remove the fill plug.
2. Rotate the pump handle counterclockwise
one full turn.
3. Pump the handle quickly ten times to purge
the air from the system.
4. Replace the fill plug and test the operation of
the jack.
—If the jack did not perform properly, then air
may need to be bled from the pump system
again.
3. Add fluid until it reaches the top of the fill plug
hole.
4. Replace the fill plug.
5. Test the operation of the jack by pumping
it up to the maximum height and applying a
load. The jack should hold the weight of the
load without a sinking or spongy feeling.
—If the jack did not perform properly, then
air may need to be bled from the pump
system.
Fill Plug
H8094 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH8094001 LIFTING ARM ASSEMBLY 22 PH8094022 TORSION SPRING
2 PH8094002 SADDLE 23 PR11M EXT RETAINING RING 25MM
3 PR03M EXT RETAINING RING 12MM 24 PH8094024 BRACE ROD
4 PH8094004 LINK ROD 25 PH8094025 COTTER PIN 4 X 50MM
5 PH8094005 RIGHT CONNECTING BOLT 26 PH8094026 EXTENSION SPRING
6 PLW12M LOCK WASHER 18MM 27 PH8094027 CONCAVE GEAR
7 PH8094007 BUTTON HD CAP SCR M12-1.75 X 25 28 PH8094028 PUMP ASSEMBLY
8 PLW05M LOCK WASHER 12MM 29 PH8094029 GEAR AXLE
9 PH8094009 FRAME 30 PW08M FLAT WASHER 16MM
10 PR07M EXT RETAINING RING 18MM 31 PH8094031 FLAT GEAR
11 PH8094011 FENDER WASHER 18MM 32 PLW06M LOCK WASHER 10MM
12 PH8094012 FRONT WHEEL 33 PH8094033 HEX NUT 10-1.5
13 PLW04M LOCK WASHER 8MM 34 PW01M FLAT WASHER 8MM
14 PN03M HEX NUT M8-1.25 35 PH8094035 COTTER PIN 2 X 12MM
15 PH8094015 REAR CASTER ASSEMBLY 36 PB52M HEX BOLT M6-1 X 35
16 PH8094016 SUPPORT ROD 37 PH8094037 LOWER HANDLE
17 PN09M HEX NUT M12-1.75 38 PH8094038 UPPER HANDLE
18 PH8094018 LEFT CONNECTING BOLT 39 PH8094039 HANDLE SLEEVE
19 PH8094019 PUMP CORE PIN 40 PH8094040 MACHINE ID LABEL
20 PH8094020 HANDLE SOCKET 41 PH8094041 FILL PLUG
21 PB49M HEX BOLT M12-1.75 X 20
The machine ID label warns about hazards and ways to prevent injury. The owner of the jack
MUST maintain the original location and readability of the label. If the label is removed or becomes
unreadable, contact Grizzly at (800) 523-4777 or www.grizzly.com to order a new label.
Other Grizzly Jack manuals
