Grizzly H5528 User manual

This gravity feed spray gun includes a 1.4mm
nozzle, a durable 600cc cup, an air adjust valve,
and a chrome finish for easy clean-up.
Figure 1. Spray gun controls.
Fluid
Control
Nozzle
Control Paint
Reservoir
Pattern
Control
Air Flow
Control
Model H5528 & H5529
Medium Duty Spray Gun
SETUP
1. Thread the paint reservoir onto the top of the
spray gun and attach the airline with a 1⁄4" NPT
fitting.
2. Adjust the air pressure so that the gun is
supplied with 30 PSI.
COPYRIGHT © SEPTEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
ADJUSTMENTS
Identify the spray gun controls in Figure 1 and
adjust in the following order:
1. Fluid Control—Adjusts how far back the
trigger can be pulled, which affects the
volume of finish released.
2. Air Flow Control—Adjusts the volume of air
that mixes with the finish, and thus,
increases or decreases the finish
atomization.
3. Pattern Control—Variably adjusts the spray
pattern from round to a wide fan.
4. Nozzle Control—Adjusts the spray pattern
from vertical to horizontal.
OPERATION
Hold the sprayer 6"–8" from the workpiece, and
keep the spray gun perpendicular to the
workpiece during strokes. DO NOT pivot your
wrist when spraying! Feather strokes by starting
your stroke before triggering the spray gun, and
releasing the trigger before finishing the stroke.
Overlap strokes by 50%
MAINTENANCE
1. Clean the spray gun passages after each use
by spraying a small amount of thinner. DO
NOT immerse the spray gun in the thinner.
2. To avoid internal damage, use only the
included brush soaked with thinner when
cleaning inside the spray gun.
3. Regularly clean the filter between the
reservoir and the spray gun.
4. Trigger, control valves, and springs should be
lubricated periodically.
EXPLOSION HAZARD! Do
not spray flammable
fluids near an open flame
or ignition source.
RESPIRATORY HAZARD!
Always wear a respirator
rated for paint and
solvent vapors when
operating the H5528 and
H5529 Spray Guns.
If you need additional help with these procedures,
call our service department at: [phone].

1
2
3 (H5528)
4 (H5529)
5
6
7
8
91011
12
13
14
15
16
1718
19 20
21
22
23
24
25
26
27
28
29
30313233
34
35
36
37
38 39 40 41 4243
44 45
46
47
48 49
50
H5528 & H5529 Parts Diagram
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH5528001 BREATHER PLUG
2 PH5528002 RESERVOIR COVER
3 PH5528003 PLASTIC RESERVOIR
4 PH5529004 ALUMINUM RESERVOIR
5 PH5528005 FILTER
6 PH5528006 FLUID INLET JOINT SEAL
7 PH5528007 FLUID INLET JOINT
8 PH5528008 HANGER
9 PH5528009 FLUID ADJ. NEEDLE
10 PH5528010 FLUID NEEDLE SPRING
11 PH5528011 JOINT CAP
12 PH5528012 FLUID ADJ. KNOB
13 PFH31M FLAT HD SCR M6-1 X 8
14 PH5528014 PATTERN ADJ. KNOB
15 PH5528015 PATTERN ADJ. KNOB
16 PH5528016 COPPER WASHER 8MM
17 PH5528017 PATTERN ADJ. SCREW
18 PH5528018 O-RING
19 PEC09M E-CLIP 6MM
20 PH5528020 AIR INLET PLUG
21 PH5528021 MULTI-TOOL WRENCH
22 PH5528022 HEX SOCKET TOOL
23 PH5528023 BRUSH
24 PH5528024 AIR ADJ. SCREW
25 PH5528025 AIR ADJ. KNOB
26 PH5528026 O-RING
27 PH5528027 DOMED SEAL WASHER
28 PH5528028 AIR ADJ. SPRING
29 PH5528029 AIR INLET VALVE
30 PH5528030 SWITCH SPRING
31 PH5528031 AIR VALVE BODY
32 PH5528032 SWITCH KNOB
33 PH5528033 O-RING
34 PH5528034 DOMED SEAL WASHER
35 PH5528035 DIRECTION SCREW
36 PH5528036 LOCKED SPRING
37 PH5528037 NOZZLE NUT
38 PH5528038 SEAL WASHER 30MM
39 PH5528039 ATOMIZATION
40 PH5528040 FLUID NOZZLE
41 PH5528041 FLUID NOZZLE PLUG
42 PH5528042 SEAL WASHER 10MM
43 PH5528043 DIRECTION SCREW
44 PH5528044 DOMED SEAL WASHER
45 PH5528045 SPRING
46 PH5528046 TRIGGER PIN I
47 PH5528047 TRIGGER PIN II
48 PH5528048 TRIGGER
49 PEC02M E-CLIP 4MM
50 PEC02M E-CLIP 4MM