Grizzly G0813 User manual

MODEL G0813/G0814/G0814X
6" JOINTER
OWNER'S MANUAL
(For models manufactured since 10/19)
COPYRIGHT © MARCH, 2016 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2019 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL18046 PRINTED IN TAIWAN V2.11.19

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table of Contents
INTRODUCTION............................................... 2
Contact Info.................................................... 2
Machine Differences ...................................... 2
Manual Accuracy ........................................... 2
Identification ................................................... 3
Controls & Components ................................. 4
G0813 Machine Data Sheet .......................... 6
G0814 Machine Data Sheet .......................... 8
G0814X Machine Data Sheet ...................... 10
SECTION 1: SAFETY..................................... 12
Safety Instructions for Machinery ................ 12
Additional Safety for Jointers ....................... 14
SECTION 2: POWER SUPPLY ...................... 15
Voltage Conversion to 220V ........................ 17
SECTION 3: SETUP ....................................... 18
Needed for Setup ......................................... 18
Unpacking .................................................... 18
G0813 Inventory .......................................... 19
G0814/G0814X Inventory ............................ 20
Hardware Recognition Chart ....................... 21
Cleanup ........................................................ 22
Site Considerations ...................................... 23
Assembly ..................................................... 24
Dust Collection ............................................. 31
Test Run ...................................................... 31
Recommended Adjustments ........................ 32
SECTION 4: OPERATIONS ........................... 33
Operation Overview ..................................... 33
Stock Inspection & Requirements................ 34
Setting Depth of Cut .................................... 35
Squaring Stock............................................. 36
Surface Planing............................................ 37
Edge Jointing ............................................... 38
Bevel Cutting................................................ 39
Rabbet Cutting ............................................. 40
SECTION 5: ACCESSORIES ......................... 42
SECTION 6: MAINTENANCE......................... 44
Schedule ...................................................... 44
Cleaning & Protecting .................................. 44
Lubrication ................................................... 45
SECTION 7: SERVICE ................................... 46
Troubleshooting ........................................... 46
Setting/Replacing Knives (G0813/G0814) ..... 48
Rotating/Replacing Helical Cutterhead
Inserts (G0814X).......................................... 50
Setting Outfeed Table Height ...................... 51
Calibrating Depth Scale ............................... 52
Adjusting Gibs .............................................. 53
Setting Fence Stops .................................... 54
Tensioning/Replacing V-Belt........................ 55
Aligning Pulleys............................................ 56
Checking/Adjusting Table Parallelism ......... 57
SECTION 8: WIRING...................................... 58
Wiring Safety Instructions ............................ 58
110V Wiring Diagram ................................... 59
220V Wiring Diagram ................................... 60
SECTION 9: PARTS....................................... 61
Table ............................................................ 61
Fence ........................................................... 63
Cutterhead .................................................. 64
G0813 Stand ................................................ 65
G0814/G0814X Stand.................................. 67
G0813 Labels & Cosmetics ......................... 69
G0814/G0814X Labels & Cosmetics ........... 70
WARRANTY & RETURNS ............................. 71

-2- Model G0813/G0814/G0814X (Mfd. Since 10/19)
We stand behind our machines! If you have ques-
tions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number
and manufacture date from the
machine ID label. This will help us help you faster.
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: [phone]
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
Contact Info
We are proud to provide a high-quality owner’s
manual with your new machine!
We
made every effort to be exact with the
instruc-
tions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that
sometimes the machine
you receive is
slightly different than shown in the manual
.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something
,
check our
website for an updated version. W
e post
current
manuals and
manual updates for free
on our web-
site at
www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write down
the
Manufacture Date and Serial Number
from
the machine ID label (see below). This information
is required for us to provide proper tech support,
and it helps us determine if updated documenta-
tion is available for your machine.
Manufacture Date
Serial Number
Manual Accuracy
INTRODUCTION
Machine Differences
Models G0813, G0814, and G0814X are 1 HP, 6"
jointers with the following differences:
• Model G0813 has a 3-knife cutterhead and a
knock-down stand that requires assembly.
• Model G0814 has a 3-knife cutterhead and a
one-piece cabinet stand.
• Model G0814X has a V-helical cutterhead
with 4 rows and 26 indexable carbide inserts.
It comes with the same one-piece cabinet
stand included with the G0814.

Model G0813/G0814/G0814X (Mfd. Since 10/19) -3-
Identification
Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.
A. Outfeed Table
B. Fence
C. Cutterhead Guard
D. Fence Lock
E. Fence Tilt Handle
F. Infeed Table
G. Infeed Table Lever
H. Fence Tilt Lock
I. Depth Scale
J. Infeed Table Lock
K. ON/OFF Paddle Switch w/Disabling Key
L. Foot Pedal Caster Assembly
M. Dust Port
N. Outfeed Table Lock
O. Outfeed Table Handwheel
For Your Own Safety Read Instruction Manual Before Operating Jointer
a) Wear eye protection.
b) Always keep cutterhead and drive guards in place and in proper operating condition. ALWAYS
replace cutterhead guard after rabbeting operations.
c) Never make jointing or rabbeting cutsdeeper than 1⁄8"or planing cuts deeper than 1⁄16".
d) Always use hold-down or push blocks when jointing material narrower than 3" or surface
planing material thinner than 3".
e) Never perform jointing, planing, or rabbeting cuts on pieces shorter than 8" in length.
ABCDE
F
G
M
O
N
K
L
I
J
H

-4- Model G0813/G0814/G0814X (Mfd. Since 10/19)
Controls &
Components
Refer to Figures 1–4 and the following descrip-
tions to become familiar with the basic controls
and components of this machine. Understanding
these items and how they work will help you
understand the rest of the manual and stay safe
when operating this machine.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
Figure 1. ON/OFF paddle switch location.
A. ON/OFF Paddle Switch w/Disabling Key:
Turns motor ON and OFF. Remove yellow
key to disable switch.
Figure 2. Main table controls, fence, and foot
pedal caster.
G
B. Fence: Guides workpiece as it moves across
cutterhead; determines angle of cut.
C. Fence Tilt Handle: Tilts fence throughout its
range of motion from 45° inward to 45° out-
ward (135°).
D. Infeed Table: Supports workpiece before it
reaches cutterhead. Position of infeed table
relative to cutterhead determines depth of
cut.
E. Infeed Table Adjustment Lever: Adjusts
position of infeed table (when infeed table
lock is loosened).
J. Infeed Table Lock: Loosens to allow adjust-
ment of infeed table height or cutting depth
tightens to secure infeed table.
G. Outfeed Table: Supports workpiece after
it passes over cutterhead. For safety and
best results, outfeed table must be properly
adjusted relative to cutterhead knives/inserts
before ANY operations (refer to Page 51 for
more details).
BC
D
E
A
J

Model G0813/G0814/G0814X (Mfd. Since 10/19) -5-
Figure 3. Cutterhead guard and depth-of-cut
scale.
H
Figure 4. Fence controls.
H. Cutterhead Guard: Covers cutterhead
until pushed out of the way by workpiece
during operation. When workpiece leaves
cutterhead, guard springs back to its starting
position.
I. Depth-of-Cut Scale: Indicates cutting depth
of a single pass.
F. Outfeed Table Handwheel: Adjusts position
of outfeed table. Typically only used when set-
ting outfeed table even with cutterhead knives/
inserts or when servicing the cutterhead.
K. Outfeed Table Lock: Loosens to allow
adjustment of outfeed table height; tightens
to secure outfeed table.
L. Fence Lock: Loosens to allow adjustment of
fence position along width of tables. Tightens
to secure fence.
M. Swing Stop: When engaged, stops fence
at 90°. When disengaged, allows fence to
adjust for bevel cuts.
N. 90° Fence Stop: When engaged, stops
fence at 90°.
Note: Even when fence stop bolt contacts
swing stop, tilt lock must be tightened before
starting machine.
Note: Swing stop must be disengaged for
bevel cuts greater than 90°.
O. 45° Fence Stop: Stops fence at 45° outward
(135°).
Note: Even when fence is resting against
stops, tilt lock must be tightened before start-
ing machine.
P. Fence Tilt Lock: Secures fence tilt setting at
desired angle.
I
K
F
L
P
N
M
O

-6- Model G0813/G0814/G0814X (Mfd. Since 10/19)
The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 3
Model G0813
MACHINE DATA
SHEET
Customer Service #: [phone] · To Order Call: [phone] · Fax #: [phone]
MODEL G0813 6" X 48" JOINTER WITH ECONOMY STAND
Product Dimensions:
Weight.............................................................................................................................................................. 247 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.
Footprint (Length x Width)..................................................................................................................... 14-1/4 x 27 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 239 lbs.
Length x Width x Height............................................................................................................. 49 x 22 x 13 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content...................................................................................................................................................... Stand
Weight...................................................................................................................................................... 13 lbs.
Length x Width x Height............................................................................................................... 16 x 19 x 6 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement............................................................................................. 110V or 220V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 110V
Full-Load Current Rating....................................................................................................... 14A at 110V, 7A at 220V
Minimum Circuit Size.......................................................................................................... 20A at 110V, 15A at 220V
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 16 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................. 5-15 for 110V
Recommended Plug Type...................................................................................................................... 6-15 for 220V
Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key
Motors:
Main
Horsepower................................................................................................................................................ 1 HP
Phase............................................................................................................................................ Single-Phase
Amps....................................................................................................................................................... 14A/7A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer .................................................................................................................................. Belt Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type......................................................................................................... External

Model G0813/G0814/G0814X (Mfd. Since 10/19) -7-
The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 3
Model G0813
Main Specifications:
Main Specifications
Jointer Size.................................................................................................................................................. 6 in.
Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R
Maximum Width of Cut................................................................................................................................ 6 in.
Maximum Depth of Cut............................................................................................................................. 1/8 in.
Minimum Workpiece Length........................................................................................................................ 8 in.
Minimum Workpiece Width....................................................................................................................... 3/4 in.
Minimum Workpiece Thickness................................................................................................................ 1/2 in.
Maximum Rabbeting Depth...................................................................................................................... 1/2 in.
Number of Cuts Per Minute..................................................................................................................... 15,000
Fence Information
Fence Length....................................................................................................................................... 29-1/8 in.
Fence Width.......................................................................................................................................... 1-1/4 in.
Fence Height............................................................................................................................................... 4 in.
Fence Stops............................................................................................................................. 45, 90, 135 deg.
Cutterhead Information
Cutterhead Type........................................................................................................................... Straight Knife
Cutterhead Diameter............................................................................................................................. 2-1/2 in.
Cutterhead Speed............................................................................................................................. 5000 RPM
Knife Information
Number of Knives............................................................................................................................................. 3
Knife Length................................................................................................................................................. 6 in.
Knife Width.................................................................................................................................................. 1 in.
Knife Thickness........................................................................................................................................ 1/8 in.
Knife Adjustment............................................................................................................................ Jack Screws
Table Information
Table Length........................................................................................................................................ 47-3/8 in.
Table Width........................................................................................................................................... 6-5/8 in.
Table Thickness.................................................................................................................................... 1-1/4 in.
Floor to Table Height........................................................................................................................... 33-5/8 in.
Table Adjustment Type........................................................................................................... Handwheel/Lever
Table Movement Type............................................................................................................. Dovetailed Ways
Construction
Base........................................................................................................................................................... Steel
Body Assembly.................................................................................................................................... Cast Iron
Fence Assembly.................................................................................................................................. Cast Iron
Guard.......................................................................................................................................... Die Cast Metal
Table....................................................................................................................... Precision-Ground Cast Iron
Paint Type/Finish....................................................................................................................... Powder Coated
Other Information
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size.............................................................................................................................................. 4 in.
Mobile Base............................................................................................................................................. Built-In
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
Serial Number Location .................................................................................................................................. ID Label

-8- Model G0813/G0814/G0814X (Mfd. Since 10/19)
The information contained herein is deemed accurate as of 11/26/2019 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 3
Model G0814
MACHINE DATA
SHEET
Customer Service #: [phone] · To Order Call: [phone] · Fax #: [phone]
MODEL G0814 6" X 48" JOINTER WITH CABINET STAND
Product Dimensions:
Weight.............................................................................................................................................................. 245 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.
Footprint (Length x Width)..................................................................................................................... 13-1/2 x 18 in.
Shipping Dimensions:
Carton #1
Type........................................................................................................................................... Cardboard Box
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 183 lbs.
Length x Width x Height............................................................................................................. 49 x 22 x 13 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content...................................................................................................................................................... Stand
Weight...................................................................................................................................................... 77 lbs.
Length x Width x Height............................................................................................................. 21 x 17 x 30 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement............................................................................................. 110V or 220V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 110V
Full-Load Current Rating....................................................................................................... 14A at 110V, 7A at 220V
Minimum Circuit Size.......................................................................................................... 20A at 110V, 15A at 220V
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 16 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................. 5-15 for 110V
Recommended Plug Type...................................................................................................................... 6-15 for 220V
Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key
Motors:
Main
Horsepower................................................................................................................................................ 1 HP
Phase............................................................................................................................................ Single-Phase
Amps....................................................................................................................................................... 14A/7A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer .................................................................................................................................. Belt Drive
Bearings........................................................................................................ Sealed & Permanently Lubricated
Centrifugal Switch/Contacts Type......................................................................................................... External