Grizzly H8090 User manual

MODEL H8090
2 Ton
Mini Aluminum Jack
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JC8821 PRINTED IN CHINA
Specifications
Maximum Lifting Capacity ............................ 4000 lbs.
Lifting Range ............................................. 57⁄16"–137⁄8"
Weight .............................................................. 21 lbs.
Identification
Figure 1 shows the main parts of the jack.
Figure 1. Model H8090 Identification.
Figure 2. Pump control knob, pump arm notch and
pump arm socket.
Carrying
Handle
Saddle
If you need help with the Model H8090, call our
Technical Support line at: [phone].
1. ALWAYS support the vehicle with appropri-
ately rated support stands before using this
jack.
2. Only use this jack on hard level surfaces
such as concrete or asphalt.
3. DO NOT overload this jack beyond the
maximum lifting capacity. Overloading can
cause the jack to collapse.
4. DO NOT use this jack to move a vehicle.
This jack is designed for lifting only.
5. Keep fingers and hands away from pinch
points when lowering
6. Always block vehicle wheels before using
this jack.
Pump Control
Knob
Pump Arm Notch
Machine
Label
Pump Arm
Socket
Failure to follow these instructions could result
in serious personal injury or death:
To raise the saddle:
Fit the pump arm notch over the pump con-
trol knob and turn the knob clockwise until it
stops, then put the pump arm into the socket
and move the arm up and down (Figure 2).
To lower the saddle:
Fit the pump arm over the control knob and
slowly turn the knob counterclockwise.
Operation

H8090 Main Parts Breakdown














 






















 
 











 








    
   

 

      

   
      
 
      

 


REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH8090001 SADDLE 24 PH8090024 HANDLE BAR
2 PH8090002 SADDLE BASE 25 PW10M FLAT WASHER 14MM
3 PH8090003 SADDLE BASE AXIS 26 PB42M HEX BOLT M5-.8 X 20
4 PH8090004 LIFT ARM 27 PN06M HEX NUT M5-.8
5 PH8090005 CONNECTION ROD AXIS 28 PW06M FLAT WASHER 12MM
6 PH8090006 SIDE FRAME 29 PN09M HEX NUT M12-1.75
7 PH8090007 FRONT WHEEL AXIS 30 PH8090030 LOCK NUT M14-2
8 PH8090008 FRONT WHEEL SLEEVE 31 PLW05M LOCK WASHER 12MM
9 PH8090009 FRONT WHEEL 32 PN02M HEX NUT M10-1.5
10 PH8090010 LINK ROD 33 PH8090033 STEEL BALL
11 PH8090011 CONNECTION BOLT 34 PH8090034 RIVET
12 PH8090012 RAISE ARM AXIS 35 PH8090035 INT TOOTH WASHER 10MM
13 PH8090013 PULL ROD AXIS 36 PH8090036 FLANGE BOLT M10-1.5 X 16
14 PH8090014 CYLINDER ASSEMBLY 37 PR06M EXT RETAINING RING 16MM
15 PH8090015 CYLINDER AXIS 38 PR45M INT RETAINING RING 10MM
16 PH8090016 CONNECTION AXIS 39 PR02M EXT RETAINING RING 14MM
17 PH8090017 HANDLE BASE 40 PH8090040 RUBBER PAD
18 PH8090018 HANDLE 41 PR10M EXT RETAINING RING 22MM
19 PH8090019 HANDLE SLEEVE 42 PB42M HEX BOLT M5-.8 X 20
20 PH8090020 REAR CASTER BRACKET 43 PB107M HEX BOLT M5-.8 X 12
21 PH8090021 REAR CASTER 44 PH8090044 MACHINE LABEL
22 PH8090022 SPRING 45 PH80900455 OIL FILL PLUG
23 PH8090023 CAP PLATE
The machine label warns about hazards and ways to prevent injury. The owner of the jack MUST maintain
the original location and readability of the label. If the label is removed or becomes unreadable, contact
Grizzly at [phone] or www.grizzly.com to order a new label.

H8090 Hydraulic Pump Parts Breakdown













































REF PART # DESCRIPTION REF PART # DESCRIPTION
101 PH8090101 BASE 118 PH8090118 PUMP CYLINDER
102 PH8090102 STEEL BALL 119 PH8090119 RING
103 PH8090103 THICK BALL HEAD 120 PH8090120 THIN BALL HEAD
104 PH8090104 ADJUSTABLE COMPRESSOR SPRING 121 PH8090121 FILTRATE NET
105 PH8090105 O-RING 122 PH8090122 OIL TANK RING
106 PH8090106 OIL RESERVOIR SEAL BOLT 123 PH8090123 CYLINDER
107 PH8090107 STEEL BALL 124 PH8090124 O-RING
108 PH8090108 O-RING 125 PH8090125 BOWL STYLE RING
109 PH8090109 RELEASE VALVE ROD ASSEMBLY 126 PH8090126 PISTON
110 PH8090110 STEEL BALL 127 PH8090127 C-RING
111 PH8090111 RING 128 PH8090128 PISTON ROD
112 PH8090112 PUMP 129 PH8090129 RECTANGLE RING
113 PH8090113 RETAINING RING 130 PH8090130 CAP SCREW
114 PH8090114 PUMP CORE - SMALL 131 PH8090131 OIL TANK
115 PH8090115 RETAINING RING 132 PH8090132 RECTANGLE RING
116 PH8090116 PUMP CORE - BIG 133 PH8090133 O-RING
117 PH8090117 O-RING 134 PH8090134 TOP CAP










