Grizzly T10035 User manual

MODEL T10035/T10036
STEEL/ALUMINUM JACKS
INSTRUCTION SHEET
T10035 Specifications
Maximum Lifting Capacity ....................3,000 lbs.
Lifting Range .......................................31⁄2"–151⁄2"
Weight .......................................................35 lbs.
T10036 Specifications
Maximum Lifting Capacity ....................5,000 lbs.
Lifting Range ..........................................4"–181⁄8"
Weight .......................................................58 lbs.
If you need help with the Model T10035 or T10036, call
our Technical Support line at: [phone].
Assembly
Attach the upper handle to the lower handle so
that the release button clicks. Insert the handle
into the handle socket. Tighten the knurled thumb
screw.
Operation
To raise the saddle:
Turn the handle clockwise as far as it will turn
and pump the handle up and down. Turning the
handle clockwise will close the release valve.
To lower the saddle:
Slowly turn the jack handle counterclockwise.
To reduce the risk of death, serious personal
injury or property damage when using these
jacks:
• DO NOT overload this jack beyond its
rated capacity. Overloading may result
in personal injury or property damage.
• ALWAYS support the vehicle with
appropriately rated support stands
before working under it.
• DO NOT attempt to move the vehicle
while the jack is in use.
• ONLY use this jack on a hard level
surface capable of sustaining the load
being supported.
• Always make sure that vehicle load
points are centered in the saddle to
maintain proper balance and stability.
• DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
• Only use the jack at appropriate areas
of the vehicle that can safely support
the vehicle's weight.
COPYRIGHT © DECEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JM10101 PRINTED IN CHINA

2 T10035/T10036 Steel/Aluminum Jacks
Maintenance
Keep the hydraulic ram clean and free of any dust,
dirt, or foreign debris. Abrasive material stuck to
the ram can damage the hydraulic seal when the
ram is retracted back into the jack. Regularly wipe
the hydraulic ram clean with a lightly oiled rag.
The jack will require hydraulic fluid after long-term
use. This will be noticeable if the jack will not
reach its maximum height when pumped.
Only use a high quality hydraulic fluid.
To add hydraulic fluid:
1. Completely lower the jack saddle.
2. Remove the fill plug shown in Figure 1.
3. Add fluid until it reaches the top of the fill plug
hole.
4. Replace the fill plug.
5. Test the operation of the jack by pumping
it up to the maximum height and applying a
load to the saddle. The jack should hold the
weight of the load without a sinking or spongy
feeling.
—If the jack did not perform properly, then
air may need to be bled from the pump
system.
Bleeding the Air
If the jack becomes spongy or will not rise when
pumped, then air bubbles may be in the hydraulic
system. These air bubbles must be bled from the
hydraulic fluid before the jack can be safely oper-
ated.
To remove the air bubbles:
1. Rotate the handle counterclockwise five full
turns.
2. Place a shop rag around and under the oil fill
hole.
3. Remove the fill plug.
4. Pump the jack handle rapidly to force the
air bubbles out through the fill hole. When
the air bubbles stop coming out, add fluid as
needed, then reinstall the fill plug.
Figure 2. Identification.
Machine
Label
Saddle
Figure 1. Fill plug.
Fill Plug
Jack Handle

3 T10035/T10036 Steel/Aluminum Jacks
T10035 Main Parts Breakdown



























 












 

    







4 T10035/T10036 Steel/Aluminum Jacks
T10036 Main Parts Breakdown











 





 

















 

















The machine label warns about hazards and ways to prevent injury. The owner of the jack MUST maintain
the original location and readability of the label. If the label is removed or becomes unreadable, contact
Grizzly at [phone] or www.grizzly.com to order a new label.

5 T10035/T10036 Steel/Aluminum Jacks
T10035 Main Parts List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT10035001 RUBBER PAD 23 PW04M FLAT WASHER 10MM
2 PT10035002 SADDLE AXIS 24 PT10035024 SCREW BUSHING
3 PT10035003 SADDLE 25 PT10035025 LINKAGE SCREW
4 PT10035004 LIFTING ARM 26 PT10035026 STRENGTHEN ROD
5 PT10035005 LIFT ARM AXIS 27 PR18M EXT RETAINING RING 17MM
6 PT10035006 LINKAGE (LONG) 28 PT10035028 HANDLE YOKE AXIS PIN
7 PR03M EXT RETAINING RING 12MM 29 PT10035029 PRESS WHEEL SHAFT
8 PT10035008 FRONT WHEEL AXIS 30 PT10035030 BRACKET
9 PT10035009 FRONT WHEEL ASSEMBLY 31 PT10035031 PRESS ROLL
10 PT10035010 WALL PLATE 32 PEC03M E-CLIP 10MM
11 PTLW16M INT TOOTH WASHER 10MM 33 PT10035033 KNURLED THUMB SCREW
12 PFB24M FLANGE BOLT M10-1.5 X 16 34 PRP37M ROLL PIN 3 X 14
13 PT10035013 SIDE HANDLE 35 PT10035035 HANDLE SOCKET
14 PFH59M FLAT HD ALLEN SCR M6-1 X 20 36 PT10035036 EYEBOLT M6-1 X 40
15 PW01M FLAT WASHER 8MM 37 PT10035037 EXTENSION SPRING
16 PTLW03M INT TOOTH WASHER 8MM 39 PN01M HEX NUT M6-1
17 PFB18M FLANGE BOLT M8-1.25 X 20 40 PT10035040 HYDRAULIC UNIT
18 PLN11M LOCK NUT M14-2 41 PFB25M FLANGE BOLT M8-1.25 X 25
19 PN02M HEX NUT M10-1.5 42 PT10035042 SPONGE SLEEVE
20 PT10035020 REAR CASTER BRACKET 43 PT10035043 LOWER HANDLE
21 PT10035021 REAR CASTER ASSEMBLY 44 PT10035044 UPPER HANDLE
22 PFB23M FLANGE BOLT M10-1.5 X 20 45 PT10035045 MACHINE ID LABEL
T10036 Main Parts List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT10036001 SADDLE AXIS 24 PT10036024 LEFT WALL PLATE
2 PT10036002 SADDLE 25 PT10036025 COTTER PIN 4 X 50
3 PT10036003 LIFTING ARM ASSEMBLY 26 PT10036026 HYDRAULIC UNIT
5 PT10036005 LINK ROD 27 PT10036027 UPPER HANDLE
6 PR06M EXT RETAINING RING 16MM 28 PT10036028 LOWER HANDLE
7 PT10036007 FRONT WHEEL AXIS 29 PT10036029 EXTENSION SPRING
8 PT10036008 FRONT WHEEL 30 PT10036030 EYEBOLT M6-1 X 25
9 PT10036009 RIGHT WALL PLATE 31 PN01M HEX NUT M6-1
10 PT10036010 FRONT WHEEL SLEEVE 32 PFB26M FLANGE BOLT M10-1.5 X 25
11 PW06M FLAT WASHER 12MM 33 PTLW16M INT TOOTH WASHER 10MM
12 PLW05M LOCK WASHER 12MM 34 PFB18M FLANGE BOLT M8-1.25 X 20
13 PN09M HEX NUT M12-1.75 35 PTLW03M INT TOOTH WASHER 8MM
14 PT10036014 SIDE HANDLE 36 PFH60M FLAT HD ALLEN SCR M8-1.25 X 20
15 PT10036015 REAR CASTER BRACKET 37 PW04M FLAT WASHER 10MM
16 PT10036016 REAR CASTER ASSEMBLY 38 PT10036038 RUBBER PROTECTIVE
17 PT10036017 LIMITATION ROD 39 PT10036039 LINK BOLT
18 PT10036018 SOCKET SHAFT 40 PR09M EXT RETAINING RING 20MM
19 PT10036019 HANDLE SOCKET 41 PLN09M LOCK NUT M12-1.75
20 PT10036020 PRESS WHEEL SHAFT 42 PR03M EXT RETAINING RING 12MM
21 PT10036021 PRESS ROLL 43 PT10036043 RAM LINK
22 PT10036022 KNURLED THUMB SCREW 44 PT10036044 MACHINE ID LABEL
23 PRP37M ROLL PIN 3 X 14

6 T10035/T10036 Steel/Aluminum Jacks
T10035 Hydraulic Pump Parts Breakdown



































REF PART # DESCRIPTION REF PART # DESCRIPTION
101 PT10035101 BASE 123 PW26MM FLAT WASHER 22MM
102 PT10035102 STEEL BALL 6 124 PT10035124 CYLINDER
103 PORP006 O-RING 5.8 X 1.9 P6 125 PORP022-4 O-RING 22.1 X 3.5 P22.4
104 PT10035104 COLLAR 126 PT10035126 CUP PACKING
105 PT10035105 COLLAR PIECE 127 PT10035127 VALVE
106 PT10035106 RELEASE VALVE ASSEMBLY 128 PT10035128 C-CLIP 20MM
107 PT10035107 STEEL BALL 8 129 PT10035129 HYDRAULIC RAM
109 PT10035109 SPECIAL SCREW M10-1.5 X 30 130 PT10035130 SEAL
110 PT10035110 STEEL BALL 4 131 PT10035131 PLUNGER CAP
111 PT10035111 BALL HOUSING 132 PT10035132 OIL TANK
112 PT10035112 ADJUSTABLE SPRING 133 PT10035133 SEAL
113 PORP008 O-RING 7.8 X 1.9 P8 134 POR0022 O-RING 22.4 X 3.1
114 PT10035114 SPECIAL SCREW M10-1 X 4 135 PT10035135 TOP NUT
115 PW27MM FLAT WASHER 17MM 136 PRP56M ROLL PIN 4 X 25
116 PT10035116 PISTON ASSEMBLY 137 PT10035137 BLOCK LINKAGE
120 PT10035120 COMPRESSION SPRING 138 PT10035138 FILTER SCREEN
121 PT10035121 PISTON COVER 139 PS19M PHLP HD SCR M5-.8 X 6
122 PR05M EXT RETAINING RING 15MM

7 T10035/T10036 Steel/Aluminum Jacks
T10036 Hydraulic Pump Parts Breakdown

 






    

















 









REF PART # DESCRIPTION REF PART # DESCRIPTION
101 PT10036101 BLOCK LINKAGE 119 PT10036119 BALL PLUNGER
102 PT10036102 COTTER PIN 120 PT10036120 ADJUSTABLE SPRING
103 PT10036103 TOP NUT 121 PORP007 O-RING 6.8 X 1.9 P7
104 PORP029-5 O-RING 29.2 X 3.5 P29.5 122 PT10036122 SPECIAL SCREW
105 PT10036105 SEAL 123 PT10036123 SPECIAL WASHER 9MM
106 PT10036106 OIL TANK 124 PT10036124 LARGE PISTON ASSEMBLY
107 PT10036107 PLUNGER CAP 128 PT10036128 COMPRESSION SPRING
108 PT10036108 SEAL 129 PT10036129 LARGE PISTON COVER
109 PT10036109 HYDRAULIC RAM 130 PR09M EXT RETAINING RING 20MM
110 PT10035128 C-CLIP 20MM 131 PT10036131 STEEL BALL 6
111 PT10036111 VALVE 132 POR0063 O-RING 6.6 X 3
112 PT10036112 CUP PACKING 133 PT10036133 RELEASE VALVE ASSEMBLY
113 PORP028 O-RING 27.7 X 3.5 P28 134 PT10036134 SMALL PISTON ASSEMBLY
114 PT10036114 CYLINDER 138 PT10036138 SMALL PISTON COVER
115 PW25MM FLAT WASHER 24MM 139 PR06M EXT RETAINING RING 16MM
116 PT10036116 FILTER SCREEN 140 PT10036140 STEEL BALL 5.5
117 PT10036117 BASE 141 PT10036141 SPECIAL SCREW
118 PT10036118 STEEL BALL 4










