Gronomics EGB 34-48 User manual

East Bethel, MN USA 763-753-7374
Continued
ITEM QTY.
1 1 FL3652 Fabric Liner, 36” x 52”
2 4 4545 Post Cap, 4-5/8” x 4-5/8” x 1-1/2”
3 2 3178N Corner Notched Bottom Board, 31-7/8” x 5-1/2” x 1
4 6 3178 Bottom Board, 31-7/8” x 5-1/2” x 1”
5 4 3100TSide Rail, 31” x 5-1/2” x 7/8”
6 2 3101T Side Rail Narrow Center, 31” x 2-1/2” x 7/8”
7 2 4501T Side Rail Narrow Center, 45” x 2-1/2” x 7/8”
8 2 4502T Side Rail w/Cleat, 45” x 5-1/2” x 7/8”
9 2 4500T, 4500TL Side Rail (one w/Logo), 45” x 5-1/2” x 7/8”
10 4 3200E Corner Post, 4” x 4” x 32” w/ 2 dovetailed sides 12-3/4
1
Parts Identification
Stack matching pieces in piles. Using the parts list,
locate and count the individual pieces and verify that
you have received the correct number of pieces.
If any pieces are missing or replacement parts
are required, contact Gronomics at
1-855-299-6727.
NOTE: Ground preparation is optional, however we
recommend leveling area under frame of product, or
place product directly on a flat level surface before
filling with soil .
Elevated Garden Bed (3 Tier 34” x 48”)
Assembly Instruction
Item #: EGB 34-48
Item #: EGB 34-48S
156
34
2
78 9 10
10
Side Rail Assembly
2
Stand two 4” x 4” x 32” corner posts (Item 10) upright with slots facing
each corner post and slots facing you.
Locate a 45” x 5-1/2” side rail w/cleat (Item 8). With cleat located at the
bottom and facing you, install side rail w/cleat into the slots and slide
down to the bottom of the slots.
Repeat procedure for the two remaining corner posts and 45” x 5-1/2”
side rail w/cleat.
(Soil depth option: Cleats located as shown will provide a soil depth of
approximately 10”. Reverse side rail w/cleat installation, cleats located at
top, if a soil depth of approximately 6” is desired.)
Cleat
10
10
10
10
8
Packaged & Inspected by: Date:
Product Care & Maintenance
Parts List
pPART # DESCRIPTION Western Red Cedar will turn a
weathered grey if left unfinished.
Although no finish is required for
cedar when used outdoors, a natural
oil finish applied regularly will help
maintain the beauty and minimize
cracking and drying. It is
recommended to use Gronomics
Garden Bed Oil (Item # GBO-1Q), a
non-toxic, food safe finish that is very
easy to apply. Apply Oil when air and
wind temperatures are between
50-90degrees. Avoid applying in
direct sunlight.
- T&G

East Bethel, MN USA 763-753-7374
7
Post Cap Assembly
6
Bottom Board and Fabric Installation
Place one 31-7/8” x 5-1/2” corner notched bottom board (Item 3) on each
end of the garden bed.
Place six 31-7/8” x 5-1/2” bottom boards (Item 4) into the garden bed.
(Gap boards evenly to allow for water drainage).
Place fabric liner into the garden bed.
Soil Capacity: 8.9 Cubic Feet
Remove the rubber cap from the corner posts studs.
Align the hole of the 4” x 4” post cap (Item 2) with stud and tighten until
the cap makes contact with the post.
NOTE: Do not overtighten.
Repeat procedure on all posts.
3
End Rail Assembly
Install two 31” x 5-1/2” side rails (Item 5) (with grooves down) into the
slots and slide down to the bottom of the slots.
4
Narrow Center Side Rail Assembly
Install two 45” x 2-1/2” narrow center side rails (Item 7) into the slots and slide
down.
Install two 31” x 2-1/2” narrow center side rails (Item 6) into the slots and slide down.
5
Final Side Rail Assembly
Rubber Cap
Stud
2
5
5
6
67
5
9
5
Logo
4
3
NOTE: Make sure the boards tongue and grooves fully seat together.
Install two 45" x 5-1/2" side rails (Item 9) (one w/logo) into the slots and slide
down. (Side rail with Logo located to outside)
Install two 31" x 5-1/2" side rails (Item 5) into the slots and slide down.
NOTE: Make sure the boards tongue and grooves fully seat together.