Gronomics EGB 34-48 User manual

East Bethel, MN USA 763-753-7374
Continued
Parts List
ITEM QTY. PART # DESCRIPTION
1 1 2001 Fabric Liner, 36” x 48”
2 4 3100 Post Cap, 4” x 4” x 1-1/2”
3 2 7026 Corner Notched Bottom Board, 31-7/8” x 5-1/2” x 1”
4 6 7025 Bottom Board, 31-7/8” x 5-1/2” x 1”
5 4 3101 Side Rail, 31” x 5-1/2” x 1”
6 2 3103 Side Rail Narrow Center, 31” x 2-1/2” x 1”
7 2 4502 Side Rail Narrow Center, 45” x 2-1/2” x 1”
8 2 7011 Side Rail w/Cleat, 45” x 5-1/2” x 1”
9 2 4501, 4501L Side Rail (one w/Logo), 45” x 5-1/2” x 1”
10 4 3201 Corner Post, 4” x 4” x 32”
1
Parts Identification
Stack matching pieces in piles. Using the parts list,
locate and count the individual pieces and verify that
you have received the correct number of pieces.
If any pieces are missing or replacement parts are
required, contact Gronomics at 1-855-299-6727.
NOTE: It is recommended to place a protective layer
between the ground and the pieces during assembly.
This will help prevent damage to the pieces.
Elevated Garden Bed (3 Tier 34” x 48”)
Assembly Instruction
Item #: EGB 34-48
Item #: EGB 34-48S
156
34
2
78 9 10
10
Side Rail Assembly
2
Stand two 4” x 4” x 32” corner posts (Item 10) upright with slots facing
each corner post and slots facing you.
Locate a 45” x 5-1/2” side rail w/cleat (Item 8). With cleat located at the
bottom and facing you, install side rail w/cleat into the slots and slide
down to the bottom of the slots.
Repeat procedure for the two remaining corner posts and 45” x 5-1/2”
side rail w/cleat.
(Soil depth option: Cleats located as shown will provide a soil depth of
approximately 10”. Reverse side rail w/cleat installation, cleats located at
top, if a soil depth of approximately 6” is desired.)
Cleat
10
10
10
10
8
Packaged & Inspected by: Date:

East Bethel, MN USA 763-753-7374
7
Post Cap Assembly
6
Bottom Board and Fabric Installation
Place one 31-7/8” x 5-1/2” corner notched bottom board (Item 3) on each
end of the garden bed.
Place six 31-7/8” x 5-1/2” bottom boards (Item 4) into the garden bed.
(Gap boards evenly to allow for water drainage).
Place fabric liner into the garden bed.
Soil Capacity: 8.9 Cubic Feet
Remove the rubber cap from the corner posts studs.
Align the hole of the 4” x 4” post cap (Item 2) with stud and tighten until
the cap makes contact with the post.
NOTE: Do not overtighten.
Repeat procedure on all posts.
3
End Rail Assembly
Install two 31” x 5-1/2” side rails (Item 5) into the slots and slide down to
the bottom of the slots.
4
Narrow Center Side Rail Assembly
Install two 45” x 2-1/2” narrow center side rails (Item 7) into the slots and
slide down.
Install two 31” x 2-1/2” narrow center side rails (Item 6) into the slots and
slide down.
5
Final Side Rail Assembly
Install two 45” x 5-1/2” side rails (Item 9) (one w/logo) into the slots and
slide down. (Side rail with Logo located to outside).
Install two 31” x 5-1/2” side rails (Item 5) into the slots and slide down.
Rubber Cap
Stud
2
5
5
6
67
5
9
5
Logo
4
3