Gronomics PTBT 59-39 User manual

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
1
Box 1 of 2
ITEM QTY. PART # DESCRIPTION
1 2 PTBT4200-X Corner Posts, 3-1/4” x 3-1/4” x 42” (X)
2 2 PTBT4200-O Corner Posts, 3-1/4” x 3-1/4” x 42” (O)
3 2 TTSB2638 Table Top Side Braces, 2” x 6” x 38” With 2 x 2 x 38” Cleat
4 4 TTLLB2624 Table Top Lower Leg Braces, 2” x 6” x 24-1/2”
5 2 TTULB2615 Table Top Upper Leg Braces, 2” x 6” x 15”
6 32 RSS516-4ZY GRK RSS Screws, 5/16” x 4”
7 28 RSS516-212ZY GRK RSS Screws, 5/16” x 2-1/2”
Picnic Table Bar Top
(59” x 39” x 42”H) Assembly Instruction
1
Parts Identification Box 1
Stack matching pieces in piles. Using the
parts list, locate and count the individual
pieces and verify that you have received
the correct number of pieces.
If any pieces are missing or replacement
parts are required, contact Gronomics at
1-855-299-6727.
NOTE: It is recommended to place a
protective layer between the ground and
the pieces during assembly. This will help
prevent damage to the pieces.
3
Item #: PTBT 59-39
Packaged & Inspected by: Date:
7
6
Torx® T30
Product Care & Maintenance
Western Red Cedar will turn a weathered grey if left unfinished. Although no finish is required for cedar when used outdoors,
a natural oil finish applied regularly will help maintain the beauty and minimize cracking and drying. It is recommended
to use Gronomics Garden Bed Oil (Item# GBO-1Q), a non-toxic, food safe finish that is very easy to apply.
Apply oil when air and wind temperatures are between 50-90 degrees. Avoid applying in direct sunlight.
5
4
2

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
2
Parts Identification Box 2
Remove contents from Box 2 of 2.
Stack matching pieces in piles. Using the parts list,
locate and count the individual pieces and verify that
you have received the correct number of pieces.
NOTE: It is recommended to place a protective layer
between the ground and the pieces during assembly.
Box 2 of 2
ITEM QTY. PART # DESCRIPTION
8 6 TTP2659 Table Top Panels, 2” x 6” x 59”
9 1 TTCP2659 Table Top Center Panel w/Hole, 2” x 6” x 59”
9
8
Corner PostAssembly
3
NOTE: Do not fully tighten screws on legs and side braces
during assembly.
NOTE: Once the leg assembly is completed and table is
placed on a level surface fully tighten screws.
Locate one 3-1/4” x 3-1/4” x 42” corner post labeled “X”
(Item 1) and one corner post 3-1/4” x 3-1/4” x 42” labeled
“O” (Item 2). Place the two corner posts on the ground
with the X & O located as shown. The two pre-drilled holes
facing up and two pre-drilled holes facing to the outside (at
the top of the corner posts).
NOTE: The two pre-drilled holes at the top of the corner
posts (facing up) (opposite of the X & O) should be farther
down and closer together than the two pre-drilled holes
located to the outside.
12
Pre-drilled Holes
Located to the
Outside
Pre-drilled Holes
Facing Up
Pre-drilled Holes
Located to the
Outside
Bottom of Corner Posts

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Lower Leg BraceAssembly
4
Locate one 2” x 6” x 24-1/2” lower leg brace (Item 4). Install
four 5/16” x 4” screws (Item 8) in the pre-drilled holes of the
lower leg brace.
Align the lower leg brace & screws with the pre-drilled holes
in the two corner posts. Tighten screws firmly but do not
fully tighten.
4
6
6
Side Brace Installation
5
Install four 5/16” x 4” screws (Item 6) in the pre-drilled holes
of the 2” x 6” x 38”side brace assembly (Item 3).
Install the side brace as shown.Align the side brace &
screws with the pre-drilled holes in the two corner posts.
Tighten screws firmly but do not fully tighten.
Repeat steps 2-4 for the other leg assembly.
3
6
6
7Lower Leg BraceAssembly Continued
6
Place one of the leg assemblies on the ground
with the lower leg brace & side brace facing
down (as shown).
Install four 5/16” x 4” screws (Item 6) in the
pre-drilled holes of a 2” x 6” x 24-1/2” lower leg
brace (Item 4).
Align the lower leg brace & screws with the pre-
drilled holes in the corner post. Tighten screws
firmly but do not fully tighten.
4
6
Side Brace
Lower Leg Brace
6

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
7
LegAssemblies
Place the leg assemblies on the ground (as
shown).
Rotate the leg assembly shown on the right up.
Align the lower leg brace (Item 4) and screws
(Item 8) with the pre-drilled holes of the leg
assembly on the right.
Tighten screws firmly but do not fully tighten.
Rotate This
Side Up and
Align Lower Leg
Brace Holes With
Lower Leg Brace
Located on Left
LegAssembly
4
Lower
Leg
Brace
Holes
6
Final Lower Leg Brace Assembly
8
Stand the leg assemblies up (as shown).
Locate the one remaining 2” x 6” x 24-1/2” lower leg brace
(Item 6). Install four 5/16” x 4” screws (Item 6) in the pre-
drilled holes of the lower leg brace.
Align the lower leg brace and screws with the pre-drilled
holes of the leg assemblies.
Tighten screws firmly but do not fully tighten
6
4
9
Upper Leg BraceAssembly
Locate the 2’x 6” x 15” upper leg brace (Item 5). Install
four 5/16” x 4” screws (Item 6) in the pre-drilled holes of the
upper leg brace.
Align the upper leg brace and screws with the pre-drilled
holes of the leg assemblies.
Tighten screws firmly but do not fully tighten.
Repeat procedure on opposite side with the one remaining
upper leg brace.
5
6

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Side Brace Marking
Measure and place a mark at the center of the side brace
(Item 3) (approximately 18-7/8” from the end of the side
brace).
Repeat procedure on side brace on opposite side of as-
sembly.
10
10
Place Mark Here
3
Side Brace
Table Top Center Panel Marking
Locate the 2” x 6” x 59” table top center panel w/hole
(Item 9). Measure 9” from the end of the panel and
place a mark. Then measure across the panel and
place a mark at the center of the panel where the first
mark was made.
Repeat procedure at the other end of table top center
panel w/hole.
11
11
Place mark at 9”
Mark center of panel
9
9

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Table Top Center PanelAssembly
Align the center mark of the table top center panel w/hole
(Item 9) with the previous mark on the on the side brace
(Item 3). Move the center panel w/hole in or out until the 9”
mark on the table top center panel w/hole is flush with the
outside edge of the side brace.
Align the opposite end of table top center panel w/hole, with
the mark on the other side brace.
NOTE: When both ends of the table top center panel w/hole
are aligned, hold down on the table top center panel w/hole
and install the two 5/16” x 2-1/2” screws (Item 7) into the
pre-drilled holes on each side brace and tighten screws into
the table top center panel w/hole.
NOTE: DO NOT over-tighten screws. Over-tightening the
screws will cause the screws to penetrate through the table
top panels.
Rubber Cap
Stud
10
10
12
12
9
3
Align Marks
7
Table Top Panel Assembly
Place a 2” x 6” x 59” table top panel (Item 8) (as
shown) and align the ends of the table top panel
with the table top center panel w/hole (Item 9).
Place the table top panel spacer (supplied with kit)
between table top center panel w/hole and the table
top panel. Install screws into the table top panel, at
both ends. (See step 12 for screw installation into
table top panels).
Remove the table top panel spacer and repeat step
13 for the remaining table top panels.
13
13
Panel Spacer
Align Table Top
Panel Ends
98

www.gronomics.com East Bethel, MN USA 763-753-7374
Final Picnic Table Bar TopAssembly
Move the table assembly to the desired location (on the
deck or in the yard). Verify that all four legs are making
contact with the ground.
Completely tighten all screws on the lower leg braces.
Adjust the table top side to side and back to front until the
table top is level. Completely tighten all screws on the side
braces and upper leg braces.
14
14