Gronomics VG 32-45UA User manual

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Parts List
ITEM QTY. PART # DESCRIPTION
1 1 4550SRB Side Panel (Right Hand) 45-1/2” x 8-7/16” x 1-1/4”
2 1 4550SLB Side Panel (Left Hand) 45-1/2” x 8-7/16” x 1-1/4”
3 7 3054BKB Back Boards 30” x 5.41” x 5/8”
4 7 3050AFB Angled Front Shelf Boards 30” x 5” X 5/8”
5 1 2925BMB Bottom Board 29-1/4” x 5.41” x 1” (w/ 4 Pre-Drlled Holes)
6 1 V1204 Top Back Board (w/ 2 Pre-Drilled Holes) 30” x 5-1/4” x 5/8”
7 1 V1205 Angled Front Shelf Board (w/ Logo) 30” x 5” x 5/8”
8 2
9 4
RSS10-234ZY
10 1 YFL Fabric Liner 36” x 10-1/4”
11 1 GBDIK
12 1 N/A
13 1 N/A
14 5 SCEY6Z
Garden Bed Drip Irrigation Kit (Contains Items 12 - 14)
Irrigation Tubing 16’
Hose Connector
Eyelet Screws
If any pieces are missing or replacement parts
are required, contact Gronomics at
1-855-299-6727.
NOTE: Ground preparation is optional, however
we recommend leveling area under frame of
product, or place product directly on a flat level
surace before filling with soil.
Vertical Garden Bed 32” x 45”
Assembly Instruction
3
Parts Identification
1
24
567
89
11
11
12
12
13
13
14
14
10
10
Item #: VG 32-45UA
Packaged & Inspected by: Date:
1
Torx® T25 Torx® T15
Product care and Maintenace Western Red
Cedar will turn a weathered grey if left unfinished. Although no
finish is required for cedar when used outdoors, a natural oil
finish applied regularly will help maintain the beauty and
minimize cracking and drying. It is recommended to use
Gronomics Garden Bed Oil (Item # GBO-1Q), a
non-toxic, food safe finish that is very easy to apply. Apply
Oil when air and wind temperatures are between
50-90degrees. Avoid applying in direct sunlight.
Stack matching pieces in piles. Using the parts
list, locate and count the individual pieces and
verify that you have received the correct number
of pieces.
Screw, RSS GRK 10 x 2-3/4"
RSS10-112ZY Screw, RSS GRK 10 x 1-1/2"

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Side Panel Assembly
2
Place the two side panels 45-1/2” x 8-7/16” x 1-1/4” (Item
1 & 2) on the ground with the slots facing each side panel
and slots slanting away from you.
12
Slots
Slots Bottom Board Assembly
4
Install the bottom board 29-1/4” x 5.41” x 1” (Item 5) onto
the side rails cleats (as shown). Install four 2” screws (Item
9) through the pre-drilled holes of bottom board and tighten
screws into the cleats located on the side panels.
9
5
Slide the back board 30” x 5.41” x 5/8” (Item 3)
from the top of the side panels down until it makes
contact with the bottom board (Item 5).
Back Board Assembly Continued
5
Top Top
5
3
Slots Back Board Assembly
3
Locate and install one back board 30” x 5.41” x 5/8” (Item
3) into the long straight slot on the bottom side of each
side panel (Item 1 & 2). Slide the back board down, until it
is flush with the top of the side panels.
3
Top Top
Bottom
2
1

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Locate and install one angled front shelf
board 30” x 5” X 5/8” (Item 4) into the
lowest slot of the side panels. Install the
angled front shelf board into the side
panel slots with the beveled edge (front
edge) facing you.
4
Beveled Edge
6
Angled Front Shelf Board Assembly
Stand the assembly up.
Locate and install the remaining back boards (Item 3).
Slide the back boards down until they make contact
with the previous back board installed.
Back Board Assembly Continued
7
3

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Position Logo Upside Down
Angled Front Shelf Board Assembly Continued
8
Locate and install one angled front shelf board
(Item 4) into the second slot from the bottom of
the side panels.
4
Drip Irrigation Kit Assembly
NOTE: The irrigation tubing will be routed through the
left side panel hole.
LEFT SIDE PANEL ROUTING- Locate and install
five eye bolts (Item 14) into the side rails. Install the
eye bolts into the pre-drilled holes in the side
panels marked with a Black “X”. (Left side panel
(Black “X”) routing shown).
14
14
9

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
NOTE: Left side panel routing shown.
Locate the irrigation tubing (Item 12). Route the
irrigation tubing (end with plug) through the hole of
the left panel and weave the irrigation tubing through
the eye bolts (bottom to top).
Drip Irrigation Kit Assembly Continued
10
10
12
12
Left Side
Panel
Hole
Right Side
Panel
Hole
Irrigation Tubing
End With Plug
Locate the hose connector and screen (Item
13). Install the screen inside the hose connecor
(screen facing out).
NOTE: Install the hose connector on the left
side panel.
Install the irrigation tubing (Item 12) onto the
hose connector and install the hose connector
into the side panel.
Drip Irrigation Kit Assembly Continued
11
11
2
13
13
13
13
12
12

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Position Logo Upside Down
Drip Irrigation Kit Assembly Continued
12
12
Remove the plug from the end of the irrigation tubing
(Item 12). Cut the tubing to the desired length. Re-
install the plug into the end of the irrigation tubing.
NOTE: If the irrigation tubing needs to be cut shorter,
always cut the hose in front of or behind the drip
section (enlarged section) of the irrigation tubing.
Plug
Drip Section
12
12
Locate and install the five remaining angled front shelf
boards (Item 4).
NOTE: The angled front shelf board (Item 7) with logo will
be installed last, at the top of the vertical garden.
Angled Front Shelf Assembly Continued
13
13
4
4
7

www.gronomics.com East Bethel, MN USA 763-753-7374
Continued
Position Logo Upside Down
Angled Front Shelf Assembly Continued
14
14
Locate the angled front shelf board with logo (Item 7).
Install the angled front shelf board with logo in the top
(vertical) slot of the side panels with the tapered (front)
edge down and facing you.
Move the vertical garden assembly to the desired
location.
NOTE: The vertical garden must be anchored to a
stable structure before filling with plant bedding.
7
SlotsStabilizing The Garden Bed
NOTE: The angled front shelf board with logo may need
to be removed to access screws while fastening the
vertical garden to the structure.
NOTE: The garden bed is not intended for hanging on a
wall or struture.
Locate and install the two 2-3/4” screws (Item 8) into the
pre-drilled holes of the top back board. Fasten the vertical
garden to a stable structure.
15
15
8

www.gronomics.com East Bethel, MN USA 763-753-7374
SlotsPlant Bedding
NOTE: Before adding the plant bedding, verify that the
vertical garden is securely fastened to a stable structure.
Verify that all back rails and shelf rails are completely
installed.
CAUTION: When filling the vertical garden with plant
bedding, support the irrigation tubing while filling. This will
help prevent damage to the irrigation tubing.
Slowly place the plant bedding into the top of the vertical
garden. Add plant bedding until it is approximately one
inch below the top back and shelf rails.
Soil Capacity: 4.5 Cubic Feet
17
17
Slots Fabric Liner
Locate the piece of fabric liner (Item 10). Place the fabric
in the bottom of the vertical garden.
NOTE: Bottom angled front shelf board has been
removed for picture clarity.
16
16
10
10