Belson Outdoors DF8WB-P User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # DF8WB-P Instructions Sheet
www.belson.com
RECYCLED PLASTIC 8’ SILHOUETTE BENCH WITH BACK

BENCH END
( 4 ) - FOUR BENCH ENDS
A - BENCH BOARD
( 3 ) - THREE BENCH BOARDS
B- BULL-NOSED BENCH BOARD
( 4 ) - FOUR BULL-NOSED BENCH BOARDS
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK

www.belson.com
1 - 3” PHILLIPS DRIVE BIT
ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
56 - #12 X 1-1/2” PAN HEAD PHILLIPS SCREWS
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.

www.belson.com
FIG #1:
IN ORDER TO MAKE THE ASSEMBLY OF THIS SILHOUETTE
BENCH EASIER WHILE GOING THROUGH THE ASSEMBLY
PROCESS THE BOARD POSITIONS ARE NUMBERED AND
WILL BE REFERENCED IN LATER STEPS.
STEP #1:
STAND ( 1 ) ONE BENCH END UP RIGHT AND PLACE ( 1 ) ONE BULL-NOSED BENCH BOARD ( B ) ON
POSITION 1, BEING SURE TO ALIGN THE PILOT HOLES TO THE PRE-DRILLED HOLES IN THE BENCH
END. AFTER THE HOLES ARE PROPERLY ALIGNED, FASTEN WITH ( 1 ) ONE #12 X 1-1/2” PAN HEAD
PHILLIPS SCREW IN THE PRE-DRILLED HOLE ON THE RIGHT SIDE OF THE BENCH END.
NOTE: DO NOT TIGHTEN SCREW COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
#12 X 1-1/2” PAN
HEAD PHILLIPS SCREW
NOTE: STAND BENCH ENDS FLAT
ON GROUND. VIEW IS ONLY TO
SHOW DETAIL.

www.belson.com
STEP #2:
STAND THE OTHER ( 3 ) THREE BENCH ENDS UPRIGHT, ONE AT TIME, AND PLACE THE BULL-NOSED BENCH
BOARD ( B ) ALREADY ATTACHED TO THE FIRST BENCH END, ON POSITION 1, BEING SURE TO ALIGN THE PILOT
HOLES WITH THE PRE-DRILLED HOLES IN THE BENCH END. AFTER THE HOLES ARE PROPERLY ALIGNED,
FASTEN WITH ( 1 ) ONE #12 X 1-1/2” PAN HEAD PHILLIPS SCREW IN THE PRE-DRILLED HOLE ON THE
RIGHT SIDE OF THE BENCH END.
NOTE: DO NOT TIGHTEN SCREWS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
#12 X 1-1/2” PAN
HEAD PHILLIPS SCREW

www.belson.com
STEP #3:
ALIGN THE PILOT HOLES ON THE BULL-NOSED BENCH BOARD ( B ) TO THE PRE-DRILLED HOLES
ON THE LEFT SIDE OF THE BENCH ENDS. AFTER THE HOLES ARE PROPERLY ALIGNED, FASTEN
WITH ( 1 ) ONE #12 X 1-1/2” PAN HEAD PHILLIPS SCREW PER BENCH END.
NOTE: BE SURE TO TIGHTEN SCREWS COMPLETELY AFTER THIS STEP.
STEP #4:
PLACE A SECOND BULL-NOSED BENCH BOARD ( B ) ON POSITION 7. REPEAT STEPS 1 – 3 TO
ATTACH. USE ( 1 ) ONE #12 X 1-1/2” PAN HEAD PHILLIPS SCREW PER HOLE TO FASTEN.
#12 X 1-1/2” PAN
HEAD PHILLIPS SCREW

www.belson.com
STEP #5:
REPEAT STEPS 1 – 3 TO ATTACH BENCH BOARDS ( A ) ON POSITIONS 2, 5, & 6 AND BULL-NOSED
BENCH BOARDS ( B ) ON POSITIONS 3 & 4. USE ( 1 ) ONE #12 X 1-1/2” PAN HEAD PHILLIPS SCREW
PER HOLE TO FASTEN.
#12 X 1-1/2” PAN
HEAD PHILLIPS SCREW