SEASIDE CASUAL FURNITURE Traditional Picnic Table 043 User manual

1
Tools Required:
Allen key
1/2” Socket
Hammer
SEASIDE CASUAL FURNITURE
(43) Traditional Picnic Table Rev. C
Hardware:
(27) 4” Carriage Bolts (5/16”)
(24) 3” Carriage Bolts (5/16”)
(51) Nuts
(51) Flat Washers
(51) Lock Washers
(4) 80mm Lags
(2) Table Slats with 3 holes (Aluminum Reinforced)
(2) Table Slats with 5 holes (Aluminum Reinforced)
(1) Center Table Slat with Umbrella hole (Aluminum
Reinforced)
(4) Legs: (2)Left and (2) Right
(1) Table Center Cleat with 2 holes
(2) Table End Cleats with 4 holes
ASSEMBLY INSTRUCTIONS
Step 1: Set Up
READ ENTIRE INSTRUCTIONS BEFORE BEGINNING! Carefully remove contents
from box. Make sure that all parts and hardware are included.
Place All Table Slats face down with Aluminum facing up
on a flat clean surface. Use the following list for placement.
1st Slat (Far Left)= Table Slat with 3 holes #1,#6,#11
2nd Slat (Middle Left)= Table Slat with 5 holes #2,#7,#12
3rd Slat (Middle)= Center Table Slat with 3 holes #3,#8,#13
4th Slat (Middle Right)= Table Slat with 5 holes #4,#9,#14
5th Slat (Far Right)= Table Slat with 3 holes #5,#10,#15
(Right Picture)
Step 2: Table Slat Placement
WARRANTY QUESTIONS OR COMMENTS PLEASE CALL TOLL FREE AT 1-800-809-3114
Parts List
(4) Seat Slats with 2 holes (Aluminum
Reinforced)
(4) Seat Cleats
(2) Angle Braces
(2) Seat Supports
Box 1: Box 2:
Instruction Revision: C

2
Step 3: Carriage Bolt Placement
Step 4: Table End & Center Cleats Attachment
Insert (19) 4” Carriage Bolts (5/16”) into all
Table Slat End and Center Holes. Tap bolts
with a hammer to set square into the End and
Center Holes (Right picture)
Align End and Center Cleats onto Carriage
Bolts by tapping them into place with a ham-
mer. Complete using (1) flat washer (1) lock
washer (1) nut per bolt and finger tighten.
(Left Picture). *Do not tighten at this time.
Step 6: Seat Support Attachment
Step 5: Leg Attachment
Place Leg along the inside of the End Cleat with
the Leg angled to the outside of the Table Top,
while aligning (2) pre-drilled holes. Attach Leg
using (2) 3” Carriage Bolts (5/16”) (Right Pic-
ture). Complete using (1) flat washer (1) lock
washer (1) nut per bolt and finger tighten. Repeat
process for all four legs. *Do not tighten at this
time.
Place Seat Support along inside of legs, while
aligning pre-drilled holes. Attach Seat Support
using (4) 3” Carriage Bolts (5/16”). Complete
using (1) flat washer (1) lock washer (1) nut
per bolt and finger tighten. (Left Picture). Re-
peat process on other side. *Do not tighten at
this time.

3
*Tighten all hardware. Do not over tighten!!! Over tightening of hardware can cause dam-
age to the item.
Step 11: Tightening of Hardware
Step 7: Angle Brace Attachment
Step 8: Flip Table to upright position
Place (2) Angle Braces along Seat Supports to the
Table Center Cleat while aligning pre-drilled
holes. Attach using (4) 80mm Lags (Socket drive).
(Right picture)
Flip Table to upright position on its legs. This will require two people.
Step 10: Seat Slat Attachment
Step 9: Seat Cleats Attachment
Place (4) Seat Cleats along inside of Seat Supports,
while aligning pre-drilled holes (AS SHOWN). Attach
using (8) 3” Carriage Bolts (5/16”). Complete using (1)
flat washer (1) lock washer (1) nut per bolt and finger
tighten. (Left Picture). *Do not tighten at this time.
Place Seat Slats on top of Seat Supports and Seat Cleats
aligning pre-drilled holes, with Aluminum side facing
down. Attach using (8) 4” Carriage Bolts (5/16”). This
may require using a hammer to tap the Carriage bolts
into pre-drilled holes. Complete using (1) flat washer (1)
lock washer (1) nut per bolt and finger tighten. *Do not
tighten at this time.