Belson Outdoors RPD6C User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # RPD6C Instructions Sheet
www.belson.com
RECYCLED PLASTIC DELUXE PICNIC TABLE

C - TABLE TOP
( 1 ) - ONE TABLE TOP
D - SEAT
( 2 ) - TWO SEATS
H - SEAT CROSS SUPPORT
( 2 ) - TWO SEAT CROSS SUPPORTS
G - UNDER SEAT SUPPORT
( 2 ) - TWO UNDER SEAT SUPPORTS
N - ANGLE SUPPORT
( 2 ) - TWO ANGLE SUPPORTS
O - CENTER SUPPORT
( 1 ) - ONE CENTER SUPPORT
K - RIGHT LEG
( 2 ) - TWO RIGHT LEGS
J - LEFT LEG
( 2 ) - TWO LEFT LEGS
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.

www.belson.com
1 - #3 PHILLIPS DRIVE BIT
2 - 9/16” SOCKET WRENCH
1 - 1/4” FLAT HEAD SCREWDRIVER
ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
2 - 3/8” X 4” HEX HEAD TAP BOLT
16 - 3/8” X 5” HEX HEAD BOLT
8 - 3/8” X 3” HEX HEAD LAG BOLT
4 - 3/8” X 2 1/2” HEX HEAD LAG BOLT
46 - 3/8” FLAT WASHER 2 - 5/8” X 1” CROSS DOWEL
16 - 3/8” NYLON LOCK NUT 8 - #12 X 3” FLAT HEAD PHILLIPS SCREW
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.

COUNTER BORE
3/8” FLAT WASHER
3/8” NYLON LOCK NUT
3/8” FLAT WASHER
3/8” X 5” HEX
HEAD BOLT
www.belson.com
STEP #1:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE LEGS TO THE UNDER TOP SUPPORTS BEING
SURE THAT THE COUNTER BORES ARE POINTING TOWARD THE CENTER OF THE TABLE AS SHOWN
ABOVE. USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND
( 1 ) 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

3/8” FLAT WASHER
3/8” X 5”
HEX HEAD
BOLT
3/8” FLAT WASHER
3/8” NYLON LOCK NUT
www.belson.com
STEP #2:
WHILE THE TABLE TOP IS UPSIDE - DOWN, FASTEN THE SEAT CROSS SUPPORTS TO THE LEGS.
USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) 3/8” NYLON
LOCK NUT PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

www.belson.com
STEP #3:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN AND ANGLE SUPPORTS TO THE SEAT CROSS
SUPPORTS AND THE CENTER TOP SUPPORT. USE ( 1 ) ONE 3/8” X 2 1/2” HEX HEAD LAG BOLT AND
( 1 ) ONE 3/8” FLAT WASHER PER HOLE TO SECURE.
NOTE: BE SURE TO TIGHTEN ALL LOOSE BOLTS AFTER THIS STEP IS COMPLETE.
NOTE:
LEG IS REMOVED TO SHOW DETAIL.
DO NOT REMOVE FOR THIS STEP.
3/8” FLAT WASHER
3/8” X 2 1/2” HEX
HEAD LAG BOLT

STEP #5:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE CENTER SUPPORT TO THE SEAT SUPPORTS.
USE ( 1 ) ONE 3/8” X 4” HEX HEAD TAP BOLT AND ( 1 ) ONE 3/8” FLAT WASHER PER HOLE TO SECURE.
5/8” X 1” CROSS DOWEL
3/8” FLAT WASHER
3/8” X 4” HEX HEAD TAP BOLT
www.belson.com
STEP #4:
PLACE ( 1 ) ONE 5/8” X 1” CROSS DOWEL IN EACH HOLE OF THE CENTER SUPPORT AS SHOWN IN THE
DIAGRAM BELOW. YOU MAY NEED TO TAP THE CROSS DOWELS IN PLACE. BE SURE THE SCORE ON
THE DOWEL HEAD IS IN LINE WITH THE LENGTH OF THE CENTER SUPPORT AS SHOWN BELOW.

STEP #6:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE UNDER SEAT SUPPORTS TO THE SEAT CROSS
SUPPORTS. USE ( 1 ) ONE 3/8” X 3” HEX HEAD LAG BOLT AND ( 1 ) ONE 3/8” FLAT WASHER PER HOLE
TO SECURE.
3/8” FLAT WASHER
3/8” X 3” HEX HEAD LAG BOLT
www.belson.com

STEP #7:
FLIP THE TABLE UPRIGHT ONTO THE LEGS. PLEASE TAKE CAUTION WHILE FLIPPING THE TABLE. AT
THIS POINT IN ASSEMBLY THE TABLE WEIGHS APPROXIMATELY 260 POUNDS.
www.belson.com

STEP #8:
WHILE THE TABLE IS UPRIGHT FASTEN THE SEATS TO THE SEAT CROSS SUPPORTS BEING SURE TO
CENTER ALL HOLES OVER BOARDS. USE ( 1 ) ONE #12 X 3” FLAT HEAD PHILLIPS SCREW PER HOLE
TO SECURE.
#12 X 3” FLAT HEAD
PHILLIPS SCREW
www.belson.com