Groz LED/180 User manual

1
INSTRUCTION MANUAL
S2820, REV A
LED 180
12 SMD + 1W SMD LED Slim
Folding Inspection Light
The super slim
worklight from GROZ
lights up all dicult to
reach, tight cluttered
workspaces with ease!
Innovative 180° Fold &
Rotate Design
• The compact folding
design makes it the
Perfect Pocket size
Inspection light
• The light Bar is only
0.24" (6mm) thick &
can rotate 180° for use
at any required angle
• Powerful 12 SMD light
bar produces super
bright light upto 400
lumens with wide
spread illumination
Intensity Control Switch
• To adjust light
intensity between
0-400 lumens as per
need
1W SMD Top Torch
• For focussed
illumination upto 70
lumens
• Hanging hook for ease
of use
Hands Free Operation
• Three super strong
magnets at the side &
rear end help ax the
light on any metallic
surface leaving both
hands free
• High impact ABS
body, polycarbonate
lens & nylon hook
• Complete with
3.7V - 2000 mAh
Lithium-ion battery
for longer life; slower
discharge than
traditional batteries
• Micro USB charging
port protected by
rubberized bezel
• Supplied complete
with 5V Braided
USB cable
Run Time
• 3-88 hours run time
on varying intensity
• 8 hours for top torch
Charge Time
• 3 hours
Size
• 11.81" × 1.77" × 1.33"
• (300 × 45 × 34 mm)
MODEL NO LED/180
BATTERY 3.7V 2000 mAh Li-ion
LED QUANTITY 12 SMD+ 1LED
LUMEN OUTPUT side: 400lm, top 70lm
OPERATING TIME side 3hr, top 8hr
CHARGING TIME 3hr
MINIMUM LENGTH 155mm
MAXIMUM LENGTH 300mm
SPECIFICATION
70
400
3-88 H 8 H
LIGHT BAR
LIGHT BAR
TOP TORCH
TOP TORCH
5V DC
USB CABLE
POWER SOURCE
IP20
WATER & DUST
PROOF RATING BATTERY
Li-ion
RUN TIME
−10°C TO +40°C
(14°F TO 104°F)
OPERATING
TEMPERATURE
11.81"
300mm
1.77"
45mm
1.33"
34mm

www.groz-tools.com
2
SAFETY INFORMATION
General
• It is important to ensure that the lamp is fully
charged before initial use.
• DO NOT turn the lamp on when it is being
charged.
• DO NOT shine directly into your, another
person’s or an animal’s eyes.
• DO NOT allow children to use the lamp.
• DO NOT leave battery in a discharged state.
Recharge battery immediately.
• Recharge the battery at least once every six
months of non-use.
• There are no user serviceable components.
DO NOT dismantle.
• DO NOT pull the charger plug from the mains
socket by the lead.
WARNING!
Battery safety
To reduce the risk of burns or fire:
• DO NOT Attempt to open, disassemble,
modify or service the battery pack.
• DO NOT Crush, puncture, short external
contacts or dispose of in fire or water.
• DO NOT Expose to temperatures above 60°C
(140°).
• Recycle or dispose of used battery as
stipulated by local regulation.
• If the electrolyte in the cells gets on your skin,
thoroughly wash with soap and water. If it
gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
INTRODUCTION
Slim folding Inspection light for use in confined
spaces, with 6mm minimum thickness.
Inspection arm can be rotated 180° and folded
back for use as a hands free inspection lamp.
Features 12 SMD LED’s which produce up to 400
lumens, operated by a rolling dimmer switch and
a 1W SMD LED in the end for use as a directional
torch. Suitable for hands free operation with
3 magnets and a hanging hook. Folds away,
small and compact, suitable for keeping in
your pocket. Powered by a 3.7V 2000 mAh
rechargeable Li-ion battery which lasts up to 8
hours. Supplied with USB charging cable.
CHARGING
Warranty is against mechanical and electrical
defect for a period of one year, this does not
cover fair wear and tear. If the battery is not
properly charged before first use, or regularly
conditioned, its capacity will diminish. Under
these circumstances we will not replace the
battery even if it is less than one year old.
Connect the charger into the charge socket on
the lamp. Plug into power supply and turn on,
the red charge LED on the lamp will light as the
battery charges. When fully charged the LED
turns green.
When the battery has fully charged (approx
3hrs) Disconnect from mains supply.
Note: The Lithium battery does not suer from
memory eect and once fully charged may be
stored for up to six months without another
charge.
OPERATION
• Unfold lamp. Select either directional torch or
inspection lamp. Brightness is controlled by
dimmer switch.
• Lamp can be hung from the hook or attached
using magnets.
MAINTENANCE
• Keep lamp clean and check for damage
before every use. If damage is observed,
remove from use until unit is repaired.
• The battery is not designed to be removed.
NOMENCLATURE
DISPOSAL
The components or the used products must
be given to companies that specialize in the
disposal and recycling of industrial waste.
Directional
torch switch
On/o & rolling
dimmer switch
Charging port
Magnet
Magnet
Hanging hook

3

Groz Engineering Tools (P) Ltd.
Groz Net Industries
Village Kherki Daula, National Highway-8,
Gurugram-122001, Haryana, INDIA
Tel [phone]
Fax [phone]
E-Mail [e-mail]
Url www.groz-tools.com
The GROZ name, GROZ logo and the mark are
trademarks of Groz Engineering Tools (P) Ltd., India