Grundig DRS 100 CL User manual

GSS
Grundig SAT Systems GmbH
Beuthener Strasse 43
D-90471 Nuremberg, Germany
Phone: +49 (0) 911 / 703 8877
Fax: +49 (0) 911 / 703 9210
E-mail: [email protected]
Internet: http://www.gss.tv
Bedienungsanleitung
Bedienungsanleitung
Operating Instructions
Operating Instructions
English
DRS 100 CI
Digital Satellite Receiver
Grundig SAT SystEms

- 2 -
- 2 -
Contents
Index .............................................................................................................................4
1 General information..................................................................................................5
1.1 Package contents........................................................................................5
1.2 Accessories for satellite receivers..................................................................5
1.3 Digital satellite reception .............................................................................5
1.4 Special features of your digital receiver ........................................................5
1.5 The common interface.................................................................................6
2 Set-up and safety ......................................................................................................6
3 Your device at a glance .............................................................................................7
3.1 The digital receiver .....................................................................................7
3.2 The SAT mouse...........................................................................................8
3.3 The remote control......................................................................................8
4 Connecting the device..............................................................................................10
4.1 Connecting the satellite antenna................................................................. 11
4.2 Connecting the television........................................................................... 11
4.3 Connecting the AV recorder/player ............................................................ 11
4.4 Connecting the SAT mouse ........................................................................ 11
4.5 Connecting the hifi system .........................................................................12
4.6 Connecting the digital multi-channel amplifier (SPDIF) ..................................12
4.7 Connecting the mains adapter ...................................................................12
5 Preparations ...........................................................................................................13
5.1 Switching the receiver on and off ...............................................................13
5.2 General menu information.........................................................................13
5.3 Setting the menu language ........................................................................14
5.4 Setting the local time ................................................................................14
5.5 Adjusting the digital receiver to the television set ..........................................15
Setting the video signal for the Euro-AV output.............................................15
Setting the screen format for the television ..................................................15
Automatic picture format identification ........................................................16
Setting the teletext style.............................................................................16
Cinch audio output level............................................................................16
5.6 Adjusting the digital receiver to the satellite antenna.....................................17
5.7 Reception of signals from encoded satellite channels ....................................19
6 Editing channel lists.................................................................................................20
6.1 Creating lists of favourites..........................................................................20
6.2 Deleting channels ..................................................................................... 21
6.3 Moving channels ......................................................................................21
6.4 Locking channels ...................................................................................... 21
6.5 Undoing the channel lock..........................................................................22

- 3 -
- 3 -
ENGLISH
7 Basic functions ........................................................................................................22
7.1 Adjusting the volume.................................................................................22
7.2 Muting ....................................................................................................22
7.3 Selecting channels – numerical preset channel selection................................22
7.4 Preset AV channel.....................................................................................23
7.5 Selecting channels from the TV/radio channel lists........................................23
7.6 Selecting channels from the list...................................................................23
7.7 Alphanumerical program selection – entering letters.....................................23
7.8 Selecting locked channels .........................................................................24
7.9 Zapping function......................................................................................24
7.10 Selecting the audio channel.......................................................................24
7.11 Teletext ...................................................................................................25
8 Updating the channel list .........................................................................................26
9 Electronic programme guide (EPG) ...........................................................................28
9.1 Displaying programme information.............................................................28
9.2 Entering programmes in the timer ...............................................................28
10 Timer functions........................................................................................................29
10.1 Entering the switch-off time for the sleep timer..............................................29
10.2 Automatically setting the timer ...................................................................29
10.3 Manually setting the timer .........................................................................29
10.4 Setting (lead time / follow-up time) options..................................................31
10.5 Ending the active timer..............................................................................31
10.6 Deleting a timer position ...........................................................................31
11 Special functions .....................................................................................................32
11.1 Hotel mode..............................................................................................32
11.1.1 Locking the menu ............................................................................32
11.1.2 Limiting the volume ..........................................................................32
11.1.3 Removing the menu lock...................................................................33
11.2 Changing the password ............................................................................33
11.3 Restoring the factory settings......................................................................33
11.4 Updating software....................................................................................34
11.5 Deleting channel lists ................................................................................35
12 Information.............................................................................................................35
12.1 Displaying information on reception of channels ..........................................35
12.2 Querying device information .....................................................................35
12.3 Technical data .........................................................................................36
12.4 Warranty ................................................................................................36
12. 5 Tro uble shootin g ........................................................................................37

- 4 -
- 4 -
Index
A
Application of data............ 29
B
Backward ..........................31
Batteries low ....................... 9
Blocking channels...............21
Blocking the menu ............. 32
C
Change channel name ........18
Channel lists.................20, 35
Cinch output level ...............16
CI module ..........................19
Cinch sockets .....................16
Common interface ............5, 7
Condition on delivery......... 33
CVBS ................................15
D
Degree of longitude ............14
Deleting channel lists.......... 35
Device information............. 35
DVB receivers...................... 5
E
Electronic programme guide 28
Encoded channels...............19
Entering letters................... 23
Environmental note............... 6
EPG ..................................28
Euro-AV .............................15
Euro-AV cable ....................11
F
F-connector ........................11
Factory settings ................. 33
Frequency ......................... 27
G
GMT .................................14
I
Information on reception..... 35
L
Language...........................14
Lead time...........................31
Limiting the volume............. 32
Lists of favourites................ 20
LNB power supply ..............17
Local time ..........................14
M
Main menu ........................13
Mains adapter....................12
Main menu ....................... 20
Menu information ...............13
Menu language..................14
Moving channels ................21
Multi-channel amplifier........12
Multi-channel sound........... 22
O
Operating software ........... 34
Optical connection .............. 7
P
Picture quality.....................15
PIN ............................. 21, 32
Polarisation ....................... 27
Power consumption .............. 6
Preset AV channel.............. 23
R
Radio station ..................... 27
Range of accessories ........... 5
Remote control..................... 8
Remote control level ............. 9
RGB ..................................15
S
Satellite antenna.................11
Satellite antennas................17
Satellites ............................18
SAT mouse ..................... 8, 11
Scart cable ......................... 5
Screen format.....................15
Sleep timer........................ 29
Smartcard..........................19
Software update................ 34
Station search ................... 27
Stereo sound ..................... 22
Summer time ......................14
System settings ...................15
T
Teletext........................16, 25
Time..................................14
Time difference...................14
Timer.................................31
Timer functions .................. 29
Timer setting...................... 29
Transponder data .............. 27
V
Volume ............................. 22
W
Wide-Screen-Signaling........16
Winter time........................14
Y
YUV ................................ 15
Z
Zapping ........................... 24

- 5 -
- 5 -
ENGLISH
1 General information
1.1 Package contents
• DRS 100 CI
• SAT mouse (infrared receiver)
• Remote control incl. 2 batteries (2 x 1.5 V, Mignon, e.g. UM-3 or AA)
• Euro-AV cable (scart cable)
• Mains adapter
• Operating instructions
1.2 Accessories for satellite receivers
You can find out more about the extensive GSS range of accessories for satellite receiv-
ing devices at your specialist dealer or at the website of
Grundig SAT Systems GmbH: http://www.gss.tv.
1.3 Digital satellite reception
To use this device you need a satellite receiving device that must be prepared for receiv-
ing digital signals. Unlike analogue satellite broadcasting, digital TV or radio channels
are not all assigned their own frequencies; instead, several TV and/or radio channels
are transmitted by a single transponder using the same frequency.
To help you with the choice and settings for satellite stations, a selection of TV and radio
stations have already been programmed for this device. You can use the channel search
to find new satellite channels that are not yet in the channel list of your device.
You can also compile your favourite channels and store them in four separate channel
lists.
1.4 Special features of your digital receiver
This digital receiver can receive free satellite channels as well as certain encoded digital
satellite channels via common interface.
To ensure that your digital receiver always uses the latest software, we recommend that
you update the operating software (see page 34).
The electronic programme guide provides an overview of all the stations‘ programmes
for the next few hours. You can call up detailed information on each TV programme at
the touch of a button.
This digital receiver has a comprehensive, easy-to-use menu system. It is displayed on
the television screen and the functions of the remote control buttons are explained.
1.5 The common interface
Common interface (CI) is the interface for DVB receivers (digital receivers, set top boxes
etc.) for decoding encoded channels. The smart card required for decoding is available
at the broadcasting station. This device has a common interface (CI) slot for this smart
card and the corresponding CI module.

- 6 -
- 6 -
2 Set-up and safety
• This digital receiver set is designed to receive and display video and audio signals.
Any other use is expressly prohibited.
• When setting up the device, make sure the mains socket is easily accessible.
• If the digital receiver is subject to a sudden change in temperature, for example when
brought in from the cold to a warm room, let it stand for at least two hours before you
connect it to the mains supply.
• Do not expose the digital receiver to any moisture. The digital receiver is designed
for use in dry rooms. If you do use it outdoors, please ensure that it is protected from
moisture, such as rain or splashing water.
• Make sure that the digital receiver is ventilated adequately.
• Do not use the device close to heating units or in direct sunlight.
• Place the device on a flat, solid surface for use.
• If placed in a cabinet, make sure there is a minimum space of approx. 10 cm
around it!
• Thunderstorms are a danger to all electrical devices. Even if the device is switched off,
it can be damaged by a stroke of lightning to the mains or the antenna cable. There-
fore always disconnect the device from the mains and from the antenna unit during a
thunderstorm.
• Never open the device under any circumstances. No liability is accepted for any dam-
age caused by incorrect handling.
Environmental note
If you do not intend to use the digital receiver for some time (for example at night), we
recommend that you switch it with to stand by. Power consumption is reduced to
approx. 0.5 Watts.

- 7 -
- 7 -
ENGLISH
3 Your device at a glance
3.1 The digital receiver
CI MODULE Common interface slot.
INPUT SAT Antenna socket for the satellite antenna.
12-24 V DC Socket for the supplied mains adapter.
RECORDER Euro AV socket (input and output) for the video or DVD recorder
TV Euro AV (output) socket for the television.
DIGITAL AUDIO OUT Optical connection for digitally encoded audio signals to the dig-
ital multi-channel amplifier (SPDIF).
AUDIO OUT R L Left/right stereo output sockets (cinch) for the hifi system.
SOFTWARE/MOUSE Socket for SAT mouse or for a PC cable.

- 8 -
- 8 -
3.2 The SAT mouse
The SAT mouse receives the infrared signals for the remote con-
trol and forwards the commands via cable to the receiver.
• Position the SAT mouse visibly so that it can receive the com-
mands by the remote control.
Note:
– The red operation indicator goes out in standby mode.
–
The operation indicator flashes if a timer has been set and
the
receiver is in standby mode.
3.3 The remote control
 Switches to standby, and from standby to the
channel last selected.
1 … 0 Select channels.
0AV mode
Switches between digital receiver mode and the
audio and video signals from the device connect-
ed to the “RECORDER” socket.
Switches the sound to mute and back on again.
TV/R Switches between radio mode and the channel
lists and lists of favourites.
MENU Opens the main menu, ends settings.
iDisplays channel information.
ZZapping function.
In menu mode: returns to the previous menu.
A/B Switches between audio channels A, B and
stereo.
◀▶ Changes the volume, controls the cursor in the
menus.
▲▼ Switches channels up and down one by one, se-
lects menu items.
OK Opens the channel list, confirms entries.
TXT Opens teletext.
EPG
Opens the electronic programme guide.
SAT Switches to remote control level SAT 2.
(Controlling of a second
receiver)
Freeze frame.
Note:
Not described functions are used for operating a
digital recorder.
Fhas no function.
RCR 100
123
456
789
0
i
MENU TV/RA/B
z
F
ABC DEF
JKL MNOGHI
TUV WXYZPQRS
Fav
Tone
AV
Exit
TXT
Timer
EPG
OK
Channel
SAT LIST

- 9 -
- 9 -
ENGLISH
Inserting batteries in the remote control
• Open the battery compartment and remove the lid.
• Insert the batteries (Mignon, e.g. UM-3 or AA, 2 x 1.5 V).
Observe the polarity marked in the battery compartment
base.
• Close the battery compartment.
Notes:
– If the digital receiver no longer reacts properly to remote
control commands or if the message “Low Battery!” ap-
pears, we recommend that the batteries are changed.
– Always remove used batteries.
The manufacturer accepts no liability for damage result-
ing from leaking batteries.
– The first time you use the digital receiver after changing
batteries, the message “Low Battery!” appears. Ignore
this message.
Environmental note
Do not throw away used batteries with your normal household waste. Instead take
them to a battery collection box in a shop or a public collection point.
Selecting remote control level SAT 1 or SAT 2
If you wish to use an RCR 100 remote control to operate two
DRS 100 CI digital
receiver , you must select a different remote
control level for one of the two digital
receiver .
TV Setup
Exit
Select Back
OK
RGB
Auto
On
MENU
Z
TV
Picture Format
WSS
Teletext
IR Level
Cinch Audio
West
SAT 1
Fixed
SAT 1
SAT 2
• Connect the device and switch it on
(see chapters 4 and 5, pages 10 … 19).
• Press the MENU button to open the main menu.
• Use ▼/▲ in the main menu to select “System Setup” and
press OK to confirm.
• U se ▼/▲ to activate “TV Setup” and press OK to confirm.
• Select “IR Level” with ▼/▲ and press OK to confirm.
• Use ▼/▲ to select remote control level “SAT 1” or “SAT 2”
and press OK to confirm.
– If you wish to use the digital receiver with remote control
level “SAT 2” press and hold the button SAT button and
at the same time press the desired function button on the
remote control.
1
2
Î

- 10 -
- 10 -
Switching the remote control to SAT 2 level
You can switch the remote control permanently to the SAT 2
remote control level.
• Press the button SAT and hold.
• At the same time press the buttons 4, 5, 6.
To return to SAT 1 remote control level
• Press the button SAT and hold.
• At the same time press the buttons 1, 2, 3.
• To finish your setting: press MENU.
4 Connecting the device
Overview
VCR, DVD etc.
R
L
AUDIO
O
U
T
DEC. - AV 2
V
CR
,
DVD etc
.
R
L
A
U
DI
O
O
U
T
DEC. -
A
V2
A
A
RECORDER TV
DIGITAL
AUDIO
OUT
AUDIO OUT
SOFTWARE/
MOUSE
RL
TV R
SAT
L
L








- 11 -
- 11 -
ENGLISH
4.1 Connecting the satellite antenna
• Connect the antenna cable to the INPUT SAT 1socket on
the digital receiver (screw connector, F-connector).
1
4.2 Connecting the television
• Plug the Euro-AV cable into the TV 2socket on the digital
receiver and into the corresponding Euro-AV socket on the
television.
2
4.3 Connecting the AV recorder/player
• Plug the commercial Euro-AV cable into the RECORDER 3
socket on the digital receiver and into the Euro-AV socket on
the AV recorder/player (e.g. video or DVD recorder).
3
Note:
To view a video or DVD recording, switch on the digital
receiver and press the 0button to select AV mode.
4.4 Connecting the SAT mouse
• Insert the plug of the SAT mouse into the SOFTWARE/
MOUSE 4socket.
4

- 12 -
- 12 -
4.5 Connecting the hifi system
• Plug a commercial cinch cable into the AUDIO OUT R L
(right/left) 5sockets on the digital receiver and the cor-
responding input sockets on the hifi system.
5
4.6 Connecting the digital multi-channel amplifier (SPDIF)
• Remove the socket cover.
• Plug a commercial optical cable (SPDIF) into the DIGITAL
AUDIO OUT 6socket on the digital receiver and the cor-
responding socket on the digital multi-channel amplifier.
6
4.7 Connecting the mains adapter
• Plug the jack plug of the supplied mains adapter into the
12-
24 V DC 7socket on the digital receiver.
• Plug the mains adapter into the socket.
7

- 13 -
- 13 -
ENGLISH
5 Preparations
Note:
Your digital receiver was set at the factory so that it is ready for operation once you
have connected it and to receive Astra channels. If required, you only need to cor-
rect the local time difference, adjust the LNB settings for receiving more satellites and
select the menu language (default is “German”, “ Single LNB”).
5.1 Switching the receiver on and off
• Switch the television to AV.
• Press  on stand by to switch on the digital receiver (opera-
tion indicator lights up red) or to switch it to stand by (opera-
tion indicator goes out).
– If a recording timer has been set, the operation indicator
flashes.
Note:
The only way to disconnect the digital receiver from the
mains supply is to unplug the mains adapter.
5.2 General menu information
– This device has a comprehensive, easy-to-use menu system.
The menus are displayed on the television screen.
– The digital receiver responds to many functions that you
can select on the remote control with informative menus and
icons on the screen. It enables you to select many different
settings and it contains information on using your digital
receiver.
– The buttons on the remote control for using the menu are
explained in the menus.
– The main menu contains the most important controls for your
digital receiver. The menu system controls the dialogue be-
tween you and the digital receiver.
–
Press the MENU button on the remote control and press
▼/▲to select the desired menu item. It is displayed on a
light background.
–
Press OK to confirm your selection. Use ▼/▲in the cor-
responding sub-menu that is now displayed to select the
desired menu item. It is displayed on a light background.
Main Menu
Exit
Select Back
OK
1 Channel List
2 System Setup
3 Channel Search
4 Timer
5 Sleep-Timer
6 Software Update
7 CI-Module
MENU
Z
– Press OK to confirm your selection. Normally another menu
then appears. There you can press ▼/▲to select the de-
sired menu item.
– You can also select the numbered menu items directly using
the numerical buttons 1 … 0.
– The
◀/▶buttons are control buttons.

- 14 -
- 14 -
– On closing the menu function, your settings are automati-
cally saved.
– You return to the previous menu via Z .
– To close the menu function press MENU.
Note:
In menu mode, you cannot press
 to switch the digital
receiver to standby.
5.3 Setting the menu language
• Press MENU to open the main menu.
• Select “System Setup” with ▼/▲and press OK to confirm.
• Select “Language, Time” with ▼/▲and press OK to con-
firm.
• Open “Language” with “OK”.
• Use ▼/▲to select the desired language and press OK to
confirm.
• To return to the previous menu: press the Z button.
• To finish your setting: press MENU.
Language, Time
Exit
Select Back
OK
Language
Time Offset
Deutsch
GMT +1 Stunde
MENU
Z
Deutsch
English
Cesky
Türkce
Español
5.4 Setting the local time
To ensure that the electronic programme guide always shows the current programmes
at the right time, you must enter the difference between your local time and GMT
(Greenwich Mean Time, degree of longitude “0”). All times given by the electronic
programme guide are then adapted to your local time.
Exit
Select Back
OK
Language
Time Offset
MENU
Z
GMT -3 hr
GMT -2 hr
GMT -1 hr
GMT
GMT +1 hr
GMT +2 hr
GMT +3 hr
GMT +4 hr
Language, Time
• Press “MENU” to open the main menu.
• Select “System Setup” with ▼/▲and press OK to confirm.
• Select “Language, Time” with ▼/▲and press OK to con-
firm.
• Select “Time Offset” with ▼/▲and press OK to confirm.
• Use ▼/▲to change the time difference in one-hour steps.
Note:
For Germany: GMT + 1 hour.
“Summer time/winter time” conversion is carried out auto-
matically.
• Confirm the setting: press OK.
• To return to the previous menu: press the Z button.
• To finish your setting: press MENU.

- 15 -
- 15 -
ENGLISH
5.5 Adjusting the digital receiver to the television set
Setting the video signal for the Euro-AV output
You can choose between the settings “CVBS” (normal pic-
ture quality, factory setting), “RGB” (high picture quality)
and “YUV” (e.g. for a connected beamer or LCD TV set).
TV Setup
Exit
Select Back
OK
TV
Picture Format
WSS
Teletext
IR Level
Cinch Audio
RGB
Auto
On
West
SAT 1
Fixed
MENU
Z
RGB
CVBS
YUV
• Select “System Setup” in the main menu with ▼/▲and
press OK to confirm.
• Select “TV Setup” with ▼/▲and press OK to confirm.
• Select “TV” with ▼/▲and then press OK to confirm.
• Use
▼/▲to select “RGB”, “CVBS” or “YUV” and press OK
to confirm.
Note:
For the settings “RGB” and “YUV” the TV set has to be pre-
pared appropriately.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.
Setting the screen format for the television
If you have a “standard” 4:3 format television, select the
“4:3” setting. If you have a 16:9 format screen, select the
“Auto” setting.
TV Setup
Exit
Select Back
OK
RGB
Auto
SAT 1
MENU
Z
4:3
Auto
TV
Picture Format
WSS
Teletext
IR Level
Cinch Audio
West
SAT 1
Fixed
• Select “System Setup” in the main menu with ▼/▲and
press OK to confirm.
• Select “TV Setup” with ▼/▲and press OK to confirm.
• Select “Picture Format” with ▼/▲and then press OK to
confirm.
• Use
▼/▲to select the desired screen format and press OK
to confirm.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.

- 16 -
- 16 -
Automatic picture format identification
If problems with the automatic picture format switchover
(e.g. 4:3, 16:9, Letterbox) arise with the connected device,
you can switch off Wide-Screen-Signaling (WSS) in this
menu.
TV Setup
Exit
Select Back
OK
RGB
Auto
SAT 1
MENU
Z
TV
Picture Format
WSS
Teletext
IR Level
Cinch Audio
West
SAT 1
Fixed
On
Off
• Use ▼/▲in the main menu to select “System Setup” and
press OK to confirm.
• Select “TV Setup” with ▼/▲and press OK to confirm.
• Use
▼/▲to select “WSS” and press OK to confirm.
• Use
▼/▲to switch WSS on/off.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.
Setting the teletext style
This menu is for setting the parameters required to display
West European or Slavic characters.
TV Setup
Exit
Select Back
OK
RGB
Auto
On
SAT 1
MENU
Z
TV
Picture Format
WSS
Teletext
IR Level
Cinch Audio
West
SAT 1
Fixed
West
East
• Use ▼/▲in the main menu to select “System Setup” and
press OK to confirm.
• Select “TV Setup” with ▼/▲and press OK to confirm.
• Use
▼/▲to select “Teletext” and press OK to confirm.
• Use
▼/▲e.g. for Germany to select “West” and press OK
to confirm.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.
Cinch audio output level
This menu is for determining whether the cinch socket output
level is to be controlled via remote control or fixed.
TV Setup
Exit
Select Back
OK
RGB
Auto
On
MENU
Z
TV
Picture Format
WSS
Teletext
IR Level
Cinch Audio
West
SAT 1
Fest
Fixed
Adjustable
• Use ▼/▲in the main menu to select “System Setup” and
press OK to confirm.
• Select “TV Setup” with ▼/▲and press OK.
• Use
▼/▲to select “Cinch Audio” and press OK to confirm.
• Use
▼/▲to select “Fixed” or “Adjustable” and press OK to
confirm.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.

- 17 -
- 17 -
ENGLISH
5.6 Adjusting the digital receiver to the satellite antenna
This digital receiver was factory set so that it is ready for operation with most satellite an-
tennas and LNB configurations. Changes in this menu have a direct effect on the reception
characteristics of the digital receiver and should therefore only be made by an expert.
• Select “System Setup” in the main menu with ▼/▲and
press OK to confirm.
• Select “LNB Settings” in the “System Setup” menu with ▼/▲
and press OK to confirm.
– The “LNB Settings” menu appears.
System Setup
Exit
Select Back
OK
2 TV Setup
3 Language, Time
4 Hotel Mode
5 Information
6 Password Setting
7 Clear Channel List
MENU
Z
8 Factory Settings
1 LNB Settings
• Select “LNB System” in the “LNB Settings”menu with ▼/▲
and press OK to confirm.
– The following is displayed in the sub-menu:
“Off”:
For switching off the LNB power supply.
“Single”: A single satellite is used for reception.
“Tone Burst”: Signals from two satellites can be re-
ceived.
“DiSEqC 1.0”: Signals can be received from up to 4
satellites.
LNB Settings
Exit
Select Back
OK
LNB System
SAT System 1
Einzeln
Astra
MENU
Z
Off
DiSEqC 1.0
Single
Tone Burst
Exit
Select Back
OK
MENU
Z
SAT System 1
LNB Type
Oscillator Low
Oscillator High
Astra
Low + High Band
09750 MHz
10600 MHz
Name
Receiving signals from a single satellite
• Select “LNB System” in the “LNB Settings” menu with ▼/▲
and press OK to confirm.
• Use
▼/▲to select “Single” and press OK to confirm.
• Select “SAT System 1” with ▼/▲and press OK to confirm.
• Use
▼/▲to select the menu item to be changed and press
OK to confirm:
– “Name“ Change the satellite name.
• Use ◀/▶to place the cursor under
the letter to be changed.
• Use
▼/▲to set letters.
• Press OK to confirm.
– “LNB Type”
• Use ▼/▲to select the LNB that is used.
• Press OK to confirm.
– “Oscillator Low” • Set the LNB oscillator frequency
(Low band).
• Use ◀/▶to place the cursor un-
der the number to be changed.
—> Enter value with 1 … 0.
• Press OK to confirm.
– “Oscillator High“ • Set the LNB oscillator frequency
(High band).

- 18 -
- 18 -
• Use ◀/▶to place the cursor under the
number to be changed.
—> Enter value with 1 … 0.
• Press OK to confirm.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.
Receiving signals from two or more satellites
• Select “LNB System” in the “LNB Settings” menu with ▼/▲
and press OK to confirm.
• Use ▼/▲to select “Tone Burst” for 2 satellites or
“DiSEqC 1.0” for up to 4 satellites and press OK to confirm.
• Select “SAT System 1” with ▼/▲and press OK to confirm.
• Use
▼/▲to select the item to be changed and press OK to
confirm:
– “Name“ Change satellite name.
• Use ◀/▶to place the cursor under
the letter to be changed.
• Use
▼/▲to set letters.
• Press OK to confirm.
– “LNB Type“ • Use ▼/▲to select the LNB that is
used.
• Press OK to confirm.
– “Oscillator Low“ • Set the oscillator frequency
(Low band).
• Use ◀/▶to place the cursor under
the number to be changed.
—> Enter value with 1 … 0.
• Press OK to confirm.
– “Oscillator High“ • Set the oscillator frequency
(High band).
• Use ◀/▶to place the cursor under
the number to be changed.
—> Enter value with 1 … 0.
• Press OK to confirm.
– “Tone Burst“ or “DiSEqC”
• Use ▼/▲to assign the LNB to the
input for the Tone Burst (A/B) or
DiSEqC switch (A … D).
• Press OK to confirm.
• Repeat the setting for all satellites “SAT System 2” etc.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.
Exit
Select Back
OK
MENU
Z
SAT System 1
LNB Type
Oscillator Low
Oscillator High
Tone Burst
Astra
Low + High Band
09750 MHz
10600 MHz
A
Name
LNB Settings
Exit
Select Back
OK
LNB System
SAT System 1
Einzeln
Astra
MENU
Z
Off
DiSEqC 1.0
Single
Tone Burst

- 19 -
- 19 -
ENGLISH
5.7 Reception of signals from encoded satellite channels
This digital receiver has a common interface (CI) slot. It allows you to connect a CI
module for various encryption systems and broadcasting stations. Encoded channels
can only be viewed with a CI module suitable for the encoding system and the corre-
sponding smart card. The smart card has all the functions for authorization, decoding
and subscription.
Note:
Follow the operating instructions of the corresponding manufacturer for the CI
module.
• Insert the smart card into the CI module in such a way that
the chip on the smart card faces the thicker side (top) of the
CI module (1.).
• Rotate CI module with inserted smart card 180° around the
longitudinal axis (bottom facing upwards, see illustration op-
posite).
• Insert the CI module with the bottom facing upwards into the
common interface slot “CI-MODULE” (2.).
1.
2.
• Use ▼/▲in the main menu to select “CI-Module” and press
OK to confirm.
– A menu generated by the CI-module appears on the
screen. For information on how to use the CI-module, see
its operating instructions.
• To return to the previous menu: press the Zbutton.
• To finish your setting: press MENU.
Main Menu
Exit
Select Back
OK
1 Channel List
2 System Setup
3 Channel Search
4 Timer
5 Sleep-Timer
6 Software Update
7 CI-Module
MENU
Z
Note:
If “Camera” is displayed in a channel window, this means
that sub-programmes are available.
• To open sub-programmes: press OK.
• Select the desired channel with ▼/▲and ◀/▶and
press OK to open.
1 General information
3 Film 2 – 11:00
2 Film 1 – 10:10
5 Film 4 – 10:40
4 Film 3 – 10:30
6 Film 5 – 10:00
8 Film 7 – 10:30
7 Film 6 – 13:00
9 Film 8 – 10:00

- 20 -
- 20 -
6 Editing channel lists
This menu is for changing the order of the preset TV and RA (Radio) channels as
desired, deleting channels you do not need and locking channels. You can select
your favourite channels and save them in four separate lists of favourites.
Main Menu
Exit
Select Back
OK
1 Channel List
2 System Setup
3 Channel Search
4 Timer
5 Sleep-Timer
6 Software Update
7 CI-Module
MENU
Z
• Select “Channel List” in the “Main Menu” with ▼/▲and
press OK to confirm.
– The TV Channel list appears.
• To change channel lists: press the TV/R button repeatedly.
Channel List TV —> Channel List RA —>
Channel List 1 —> Channel List 2 —> Channel List 3 —>
Channel List 4 —> Channel List TV.
6.1 Creating lists of favourites
• Select “Channel List TV” with TV/R.
• Select the channel to be entered into the list of favourites
with ▼/▲or ▼/▲and
◀/▶ press the (yellow) button to
open the “List of favourites” menu.
• Select the desired list of favourites with ◀/▶and press OK
to highlight in white the selection.
Channel List TV
TV/RA... Delete Exit
Info Sort
Protect List 1... Back
1 Das Erste
2 SAT.1
3 RTL Television
4 RTL2
5 ZDF
6 Super RTL
7 VOX
8 Pro Sieben
1234
MENU
TVR
i
Z
1234
Insert
• To enter a channel in the list of favourites: press the (yellow)
button.
– The selected channel is stored in the list of favourites
(white).
– The next channel is automatically selected in the TV chan-
nel list
.
• If you wish to enter the automatically selected channel in
the list of favourites, press the (yellow) button, otherwise use
▼/▲and ◀/▶ to select the channel to be moved and
proceed as described above.
1
Insert
234
Notes:
– You can enter the selected channels in several lists of
favourites at the same time:
• Use ◀/▶to place the cursor in succession under the
icons to be activated from the lists of favourites and
press
OK each time to confirm.
– To deactivate an active
list of favourites use ◀/▶to place
the cursor under the icon for this list and press OK to con-
firm.