Grundig DTR 2420 User manual

ǵ
DIGITAL
TERRESTRIAL
RECEIVER
DTR 2420
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
SUOMI
ESPAÑOL

2
CONTENTS____________________________________________
4 General information
4 Packing contents
4 Receiving digital stations
4 Special features of your digital receiver
5 Set-up and safety
6-8 Overview
6 The front of the digital receiver
7 The back of the digital receiver
8 The remote control
9-10 Connection and preparation
9 Connecting the antenna
9 Connecting the television
9 Connecting a video recorder
10 Connecting a hi-fi system
10 Connecting a digital multi-channel amplifier
10 Connecting the power cord
10 Inserting batteries in the remote control
11-18 Settings
11 The menu
12 Searching for stations
13 Editing the station list
14 Creating a list of favourite stations
15 Setting the local time
16-17 Adjusting the digital receiver to the television set
17-18 Audio settings
19-21 Basic functions
19 Switching on and off
19 Mode selection
19 Selecting preset channels
19 Adjusting the volume
20 Muting the sound
20 Selecting stations from lists
20 Switching from the current station to the previous one
21 TV Guide
21 Subtitles
22-27 Additional functions
22 Setting the menu language
22 Switching the DC voltage for an active indoor antenna
22 Channel raster/country
23 Automatic station search
24 Manual station search
24 Deleting stations automatically
25 Selecting the video channel
26-27 Timer functions

ENGLISH
3
CONTENTS _________________________________________________
28 Special settings
28 Resetting the digital receiver to its original state
28 Updating the digital receiver software
29-31 Information
29 Displaying station reception properties
29 Displaying device information
29 Connecting the digital receiver to a PC
30 Technical data
31 Rectifying minor problems

4
Packing contents
1DTR 2420 digital satellite receiver
2Tele Pilot 765 S remote control
32 batteries for the remote control (2 x 1,5 V, Mignon, e.g.
UM-3 or AA)
4Euro/AV (Scart) cable
5Power cord
6Operating manual
Receiving digital stations
To use your new DTR 2420 digital receiver you need a digital
outdoor or indoor antenna.
Unlike analogue broadcasting, not every station has its own trans-
mission frequency. Instead, several stations are grouped into what
are known as bouquets on a regional or national level.
You can find the current transmission information on teletext from
various broadcasters, or look in a TV guide or on the Internet.
Special features of your digital receiver
The DTR 2420 digital receiver can receive and process all unen-
crypted digital stations. This digital receiver has a built-in digital
receiver unit. The receiver unit converts the signals from digital
stations to provide outstanding audio and picture quality.
The TV guide tells you of any schedule changes at short notice, and
provides an overview of all the stations’ schedules for the next few
hours.
If the broadcaster provides it, you can call up detailed information
on each programme at the touch of a button.
This digital receiver has a very comprehensive, user-friendly menu
system.
The menu is displayed on the television screen, and the functions of
the remote control buttons are explained.
GENERAL INFORMATION__________________

ENGLISH
5
SET-UP AND SAFETY___________________________
°C2h
°C
ǵ
ON/OFF
RADIO
TV
DTR2420 DIGITALTERRESTRIAL RECEIVER
-T
ǵ
ON/OFF
RADIO
TV
DTR 2420 DIGITALTERRESTRIAL RECEIVER
- T
ǵ
ON/OFF
RADIO
TV
DTR 2420 DIGITAL TERRESTRIAL RECEIVER
- T
Krieg im Balkan
ǵ
ON/OFF
RADIO
TV
DTR 2420 DIGITAL TERRESTRIAL RECEIVER
- T
EURO AV1 TV
EURO AV2 VCR
AUDIO OUT
DIGITAL
RS 232
L
R
230V~ 50 Hz
10W max.
OUTPUT TER.
INPUT TER.
VHF/UHF
5 Vјmax. 30 mA
To ensure that that this high quality, easy-to-use digital receiver
gives you lasting entertainment and enjoyment, please note the
following information.
This digital receiver is designed to receive, record and play back
video and audio signals. Any other use is expressly prohibited.
When setting up the digital receiver, make sure it is in a horizontal
position and that the mains socket is easily accessible.
Please note when setting up the digital receiver that furniture sur-
faces are coated with various types of paint and plastic, which often
contain chemical additives. These additives may cause corrosion to
the feet of the unit. This may leave stains on the surface of the
furniture which can be difficult or impossible to remove.
If the digital receiver is subject to a sudden change in temperature,
for example when brought in from the cold to a warm room, let
it stand for at least two hours before you connect it to the mains
supply.
Do not expose the digital receiver to any moisture.
The digital receiver is designed for use in dry rooms. If you do use it
outdoors, please ensure that it is protected from moisture, such as
rain or splashing water. Do not place any vessels such as vases on
the digital receiver. These may be knocked over and spill fluid on
the electrical components, thus presenting a safety risk.
Do not place the digital receiver close to heating units or in direct
sunlight, as this will impair cooling. Place the digital receiver on a
hard, level surface. Do not lay any objects such as magazines on
the digital receiver. When placed in a cabinet, make sure there is a
minimum space of 10 cm around it.
Thunderstorms are a danger to all electrical devices. Even if the
digital receiver player is switched off, it can be damaged by a
lightning strike to the mains or the antenna.
Always disconnect the mains and antenna plugs during a storm.
Never open the digital receiver casing under any circumstances.
Warranty claims are excluded for damage resulting from improper
handling.

6
The front of the digital receiver
ON/OFF Switches the digital receiver to standby mode and
Ǽoff again.
•(red) The digital receiver is in standby mode.
•RADIO Lights up in radio mode.
•TV Lights up in TV mode.
iOpens and closes the main menu.
P+, P- Switch channels up and down one by one.
Switch the digital receiver on from standby.
In the menus: move the cursor up/down, select and change
individual entries.
Ǹ, ǷChange the volume.
In the menus: move the cursor left/right, select and change
individual entries.
OK Opens the station list.
In the menus: confirms entries.
OVERVIEW____________________________________________
ǵ
ON/OFF
RADIO
TV
DTR 2420 DIGITAL TERRESTRIAL RECEIVER
- T

ENGLISH
7
OVERVIEW_________________________________________________
The back of the digital receiver
INPUT TER. Socket for the indoor or outdoor antenna.
OUTPUT TER. HF output for connecting an HF cable to the anten-
na socket on the television or video recorder.
AUDIO OUT Left/right stereo sockets (cinch) for hi-fi system.
R L
AUDIO OUT Audio output sockets for digital audio signal (cinch)
DIGITAL for digital multi-channel amplifier.
EURO AV 2 ɮVCR Euro AV socket (input and output) for the video
recorder.
EURO AV 1 ɮTV Euro-AV (output) socket for the television.
RS 232 Serial interface for connecting to a PC.
230 V
~/ 50 Hz Connection socket for the power cord supplied.
10 W max.
Note:
The model designation can be found on the back
of the digital receiver.
EURO AV 1 TV
EURO AV 2 VCR
AUDIO OUT
DIGITAL
RS 232
L
R
230 V~ 50 Hz
10 W max.
OUTPUT TER.
INPUT TER.
VHF/UHF
5 V
ј
max. 30 mA

8
OVERVIEW ________________________________________________
The remote control
ǼSwitches the digital receiver to standby, and from
standby to the channel last selected.
ECalls up the device connections menu.
?Displays programme information.
1 ... 0 Select stations.
dSwitches the sound to mute and on again.
iOpens the main menu.
zSwitches between the two most recently selected
channels.
ǸAdjust the volume.
Ƿ
P+ Switch channels up and down
P- one by one.
Switch the digital receiver from standby to the most
recently selected channel.
OK Opens the station list.
TV-G Calls up the TV guide.
TV Switches to TV mode.
RADIO Switches to radio mode.
ȄOpens the »Record timer« menu.
ǷǷOpens the »Subtitles« menu.
FOpens the »Sound« menu.
AVR, TV Switches to operating a GRUNDIG AV receiver,
DVD AV receiver, GRUNDIG television or
GRUNDIG DVD player.
Keep the appropriate button (»AVR«, »TV«, »DVD«)
pressed down. Then press the required button.
Note:
The functions available depend on the model of the
device you are using.
Just try it out.
Tele Pilot 765 S
AVR DVD
TV
z
TXT
PIP
A/B
MHP
d
TV-G
Radio
TV

ENGLISH
9
Connecting the antenna
1Connect the cable of the indoor or outdoor antenna to the »INPUT
TER.« socket on the digital receiver.
Note:
When connecting an indoor antenna you may have to try it out at
different positions until you get the best reception.
2Connect the »OUTPUT TER.« socket on the digital receiver via an
HF cable to the antenna socket on the television (loop-through function
for analogue stations).
Connecting the television
1Plug the Euro-AV (Scart) cable supplied into the »EURO AV1 ɮTV«
socket on the digital receiver and the corresponding Euro-AV socket
(e.g. EURO-AV, SCART) on the television.
Connecting a video recorder
1Plug a standard Euro-AV (Scart) cable into the »EURO AV2 ɮVCR«
socket on the digital receiver and the Euro-AV socket (e.g. EURO-AV,
LINE IN/OUT, EXT.1) on the video recorder.
Note:
When playing back a video recording, the video and audio signal from
the video recorder is automatically looped through to the television via
the »EURO AV1 ɮTV« socket on the digital receiver.
The digital receiver must be in standby mode.
It may not be switched off by the power switch.
CONNECTION AND PREPARATION__
EURO AV 1 TV
EURO AV 2 VCR
AUDIO OUT
DIGITAL
RS 232
L
R
230 V~ 50 Hz
10 W max.
OUTPUT TER.
INPUT TER.
VHF/UHF
5 Vјmax. 30 mA
R
L
AV1
AV2
ń
R
L
AUDIO
R
L
I
N
O
U
T
DEC. - AV 2
EURO - AV 1
TV R
D
OUTPUT TER.
INPUT TER.
VHF/UHF
5 V
ј
max. 30 mA
EURO AV 1 TV
EURO AV 2 VCR
AUDIO OUT
DIGITAL
L
R
OUTPUT TER.
INPUT TER.
VHF/UHF
5 V
ј
max. 30 mA
EURO AV 1 TV
EURO AV 2 VCR
AUDIO OUT
DIGITAL
L
R
OUTPUT TER.
INPUT TER.
VHF/UHF
5 V
ј
max. 30 mA

10
Connecting a hi-fi system
1Plug a standard cinch cable into the »AUDIO L R« sockets (left/right)
on the digital receiver and the corresponding input sockets on the hi-fi
system.
Connecting a digital multi-channel amplifier
1Plug a standard cinch cable into the »DIGITAL« socket on the digital
receiver and the corresponding socket on the digital multi-channel
amplifier.
Connecting the power cord
1Plug the power cord supplied into the »230V~/50Hz« socket on the
digital receiver.
2Plug the power cord into the wall socket.
Inserting batteries in the remote control
1Open the battery compartment by removing the lid.
2Insert the batteries (Mignon type, for example UM-3 or AA, 2 x 1.5 V).
Observe the polarity (marked on the base of the battery compartment).
3Close the battery compartment.
Note:
If the digital receiver no longer reacts properly to remote control com-
mands, the batteries may be flat. Be sure to remove used batteries.
The manufacturer accepts no liability for damage resulting from leaking
batteries.
Environmental note
Batteries, including those which contain no heavy metal, may not be
disposed of with household waste. Please dispose of used batteries in an
environmentally sound manner. Find out about the legal regulations
which apply in your area.
CONNECTION AND PREPARATION_________________
AUDIO OUT
DIGITAL
L
R
OUTPUT TER.
INPUT TER.
VHF/UHF
5 Vјmax. 30 mA
V
C
RRS 232
230 V~ 50 Hz
10 W max.
AUDIO OUT
DIGITAL
L
R
OUTPUT TER.
INPUT TER.
VHF/UHF
5 Vјmax. 30 mA

ENGLISH
11
The menu
This digital receiver has a very comprehensive, user-friendly menu
system. The menu is displayed on the television screen.
The digital receiver responds to many functions which you select on
the remote control with informative menus and icons on the tele-
vision screen.
It enables you to select many different settings and contains infor-
mation on using your digital receiver.
The buttons on the remote control for using the menu are explained
on the screen.
The main menu contains the most important controls for your digital
receiver. Its menu system controls the dialogue between you and the
digital receiver.
Press »i« to open the main menu. Press »P-« or »P+« to navigate
the menu and select items. The selected item is highlighted.
When you press »OK« to confirm your selection, a sub-menu
appears. Here too, you can navigate by pressing »P-« or »P+«
and select the item you want. The selected item is highlighted.
Press »OK« to confirm. Normally another menu then appears,
where you can use »P-« or »P+« to navigate and make the setting.
Make settings using »P-«, »P+«, »Ǹ« or »Ƿ«.
Press »z« to quit the current menu level.
Press »i« « to quit the menu entirely.
Note:
In menu mode, you cannot press »Ǽ« to switch the digital receiver
to standby.
SETTINGS ______________________________________________
Main menu
Select Back Exit
and open
Settings
Preset list
Info
Timer
Installation
ǵ

12
Searching for stations
The automatic search looks for receivable stations among the avail-
able bouquets of digital stations.
1Switch on the digital receiver by pressing »Ǽ« on the receiver.
– The »Menüsprache« (Language) menu appears when the
device is first switched on.
2Select your language using »P-« or »P+« and press »OK« to
confirm.
– The »Country« menu appears.
3Press »P-« or »P+« to select the country and press »OK« to
confirm.
– The »Antenna voltage« menu appears.
Caution!
Only switch on the antenna voltage if the antenna is an active
indoor antenna with a signal amplifier with no power supply
of its own from a mains adapter or similar source. Otherwise
you may cause a short circuit and irreversibly damage your
antenna.
4Press »P-« or »P+« to switch the antenna voltage on or off and
then press »OK« to confirm.
Caution!
If the message »Short circuit or overload at the antenna input«
appears, switch off the digital receiver immediately using the
power switch and rectify the problem. The antenna has an
excessive current consumption (max. 30 mA) or a short circuit.
– The »Search result« page appears and the station search
begins.
– After the search, the message »Sort?« appears.
5Press »Ǹ« or »Ƿ« to select »Yes« (the stations are sorted before
being transferred to the station list) or »No« (the stations are
transferred unsorted to the station list) and press »OK« to
confirm.
– After sorting, the receiver switches to preset channel 1.
– You can change the order of preset stations as required and
delete stations you do not need (see page 13 “Editing the
station list”).
SETTINGS _________________________________________________
Menüsprache
Auswählen
und aufrufen
Deutsch Türkçe
English Español
Suomi
Français
Italiano
ǵ
Country
Select Back
and change
Germany Italy
Austria Finland
Australia
France
Spain
Antenna power
Select Back
and change
Off
On

ENGLISH
13
SETTINGS _________________________________________________
Editing the station list
You can change the order of preset stations as required and delete
stations you do not need.
1In the main menu, select »Preset list« with »P+« or »P-« and
press »OK« to confirm.
2Select »Sort« by pressing »OK«.
– The station list appears.
Deleting stations
1Press »P-« or »P+« to select the station to delete and press
»OK« to confirm.
– The station is highlighted in orange.
2Select the next station with »P-« or »P+« and press »OK« to
confirm.
3Press »z« to delete the stations.
– The highlighted stations are deleted.
Moving stations
1Press »P-« or »P+« to select the station to move and press
»OK« to confirm.
– The station is highlighted in orange.
2Select the next station with »P-« or »P+« and press »OK« to
confirm.
3Press »P-« or »P+« to select the channel in front of which the
station is to be inserted.
4Press »ǷǷ« to move the stations.
Ending the settings
1Press »i« and then »OK« to save the settings.
Preset list
Select Back Exit
and open
Sort
Edit bookmarks
Sort
Channel 5
1 Sat 1
2 ProSieben
3 KABEL1
4 NEUN LIVE Telev
5 DSF
6 HSE24
7SAT.1
8 N24
9 TELE 5
10 Das Erste
Select Back Exit
and open Delete Add

14
Creating a list of favourite stations
You can select your favourite stations and save them in a list.
1In the main menu, select »Preset list« with »P+« or »P-« and
press »OK« to confirm.
2Select »Edit bookmarks« with »P+« or »P-« and press »OK«
to confirm.
– The »Edit bookmarks« page appears.
3Press »P-« or »P+« to select the station to move and press
»OK« to confirm.
– The station is highlighted in orange.
4Select the next station with »P-« or »P+« and press »OK« to
confirm.
5To move the stations, press »A/B« and then press »OK« or
»ǷǷ« to confirm.
– You can switch between the station list and your favourites by
pressing »A/B«.
– You can change the order of the stations or delete ones you
do not need (see the section on editing the station list).
Note:
If you delete a station from the station list, it is also deleted from
your favourites.
6Press »i« and then »OK« to save the settings.
SETTINGS _________________________________________________
Preset list
Select Back Exit
and open
Sort
Edit bookmarks
Edit bookmarks
Select Back Exit
and open Delete Add
Change
Preset list
1 Sat 1
2 ProSieben
3 KABEL1
4 NEUN LIVE Telev
5 DSF
6 HSE24
7SAT.1
8 N24
9 TELE 5
Bookmarks
1 Sat 1
A/B

ENGLISH
15
Setting the local time
To ensure that the TV guide always shows the current programmes
at the right time, you must enter the difference between your local
time and GMT (Greenwich Mean Time at longitude “0”).
All times given by the TV guide are then converted to your local
time.
With clock changes (e.g. daylight saving time), you need to correct
the time difference.
1In the main menu, select »Installation« with »P-« or »P+« and
press »OK« to confirm.
2Select »Time« with »P-« or »P+« and press »OK« to confirm.
3Select »Time difference« with »OK« and then use »P-« or
»P+« to enter the time difference in 30 minute increments.
Note:
The »Current time« item is for information only and cannot be
selected.
4Press »OK« to confirm the setting.
5Press »i« and then »OK« to save the settings.
SETTINGS _________________________________________________
Installation
Select Back Exit
and open
Menu language
Station search
Video output
Time
Antenna connection
Special functions
Info
Time
Select Back Exit
and open Ȅ
Current time 08:05 o’clock
+2.00 Hours
Time difference

16
Adjusting the digital receiver to the television set
Specifying the video signal at the Euro AV (TV)
output
You can choose between the settings »FBAS« (normal picture
quality), »RGB« (high picture quality) »Y/C« (S-Video signal) and
»YUV« (component signal). The default setting is »RGB«.
1In the main menu, select »Installation« with »P-« or »P+« and
press »OK« to confirm.
2Select »Video output« with »P-« or »P+« and press »OK« to
confirm.
3Select »Signal type« by pressing »OK«.
4Press »P-« or »P+« to select the setting and press »OK« to
confirm.
5Press »i« and then »OK« to save the settings.
Selecting the television picture format
If you have a 4:3 format television or flat screen, select the »4:3«
setting.
If you have a 16:9 format television or flat screen, select the »16:9«
setting.
1In the main menu, select »Installation« with »P-« or »P+« and
press »OK« to confirm.
2Select »Video output« with »P-« or »P+« and press »OK« to
confirm.
3Select »TV format« by pressing »P-« or »P+« and press »OK«
to confirm.
4Press »P-« or »P+« to select the picture format and press
»OK« to confirm.
Note:
If picture format 4:3 is selected, you can also select picture
conversion.
5Press »i« and then »OK« to save the settings.
SETTINGS _________________________________________________
Installation
Select Back Exit
and open
Menu language
Station search
Video output
Time
Antenna connection
Special functions
Info
Video output
Select Back Exit
and open Ȅ
TV format
Signal type RGB
16:9
Video output
Select Back
and change Ȅ
RGB
16:9
Signal type 4:3
16:9
TV format

Selecting the television picture conversion
If you have a 4:3 format television or flat screen, the following
settings are available:
»Pan-Scan« for wide-screen playback without black bars on the top
and bottom edges of the screen.
»Letterbox« for wide-screen playback with black bars on the top
and bottom edges of the screen.
1In the main menu, select »Installation« with »P-« or »P+« and
press »OK« to confirm.
2Select »Video output« with »P-« or »P+« and press »OK« to
confirm.
3Select »Picture conversion« with »P-« or »P+« and then press
»OK«.
4Press »P-« or »P+« to select the conversion and press »OK« to
confirm.
5Press »i« and then »OK« to save the settings.
Audio settings
1In the main menu, select »Settings« with »P-« or »P+« and
press »OK« to confirm.
2Select »Sound« by pressing »OK«.
– The »Sound« menu appears.
Note:
Further operation is explained in the following sections.
Changing the audio channel of the television
Here you can find information on the number of audio channels
(i.e. the language of the current TV or radio program). You can
switch to a different language during programs broadcast in
several languages. In radio mode, you can switch to other pro-
grammes.
1Select »Sound channel TV« with »P-« or »P+« and then press
»OK«.
2Press »P-« or »P+« to select the setting and press »OK« to
confirm.
Sound
English
Stereo
❙
■■❙ ■■■■■■ ❙
Same as TV
ENGLISH
17
SETTINGS _________________________________________________
Video output
Select Back
and change Ȅ
RGB
4:3
Signal type
Letterbox
Pan-Scan
TV format
Picture conversion
Sound
Select Back Exit
and open
Sound channel TV
Sound settings
Volume adjustment
Sound channel Dig.
English
Stereo
❙
■■❙
■■■■■■ ❙
Same as TV
Select Back
and change
Sound channel TV
Sound settings
Volume adjustment
Sound channel Dig.

Sound settings
Here you can select the audio mode, such as stereo, mono (left) and
mono (right).
1Select »Sound settings« by pressing »P-« or »P+« and press
»OK« to confirm.
2Press »P-« or »P+« to select the setting and press »OK« to
confirm.
Volume adjustment
You can set the standard volume here. This is the volume of the
device after switching on.
1Select »Volume adjustment« by pressing »P-« or »P+« and
press »OK« to confirm.
2Press »Ǹ« or »Ƿ« to set the level and press »OK« to confirm.
Selecting the audio channel for the digital output
You can choose the audio mode for the digital output (e.g. AC-3
Stereo). The choice of audio depends on the station and the current
programme.
1Select »Sound channel Dig.« by pressing »P-« or »P+« and
press »OK« to confirm.
2Press »P-« or »P+« to select the setting and press »OK« to
confirm.
– You can only change the setting if digital audio (AC-3) is
transmitted.
– The setting is automatically stored for the current station
(until you switch off the digital receiver using the main power
button).
Ending the settings
1Press »i« and then »OK« to end the settings.
Sound
18
* Under license from Dolby Laboratories Licensing Corporation.
DOLBY and the Double-D symbol ijare registered trademarks of the
Dolby Laboratories Licensing Corporation.
SETTINGS _________________________________________________
Sound
Select Back
and change
Volume adjustment
English
Stereo
❙
■■❙ ■■■■■■ ❙
Wie Tonkanal TV
As TV audio channel
AC-3 Stereo
Sound channel TV
Sound settings
Sound channel Dig.
Sound
Select Back
and change
Volume adjustment
English
Deutsch
❙
■■❙ ■■■■■■ ❙
Same as TV
Stereo
Mono (left)
Mono (right)
Sound settings
Sound channel Dig.
Sound channel TV
Select Back
and change
Sound channel TV
Sound settings
English
Stereo
❙
■■
■■❙
■■■■■■ ❙
Same as TV
Sound channel Dig.
Volume adjustment

ENGLISH
19
Switching on and off
1Press »Ǽ« to switch on the digital receiver from standby mode.
– The mode indicator lights up green (TV mode) or yellow
(radio mode).
2Press »Ǽ« to switch the digital receiver to standby mode.
– The mode indicator lights up red.
Mode selection
You can choose between TV and radio modes.
1Press » « or » « to select the mode.
Note:
You can also change modes by selecting »Info« in the main
menu.
Selecting preset channels
1Move up and down the channels by pressing »P+« or »P-« as
required.
2To run through the channels, press and hold down »P+« or
»P-«.
3Enter single-digit or multi-digit preset channel numbers by
pressing »1 ... 0« on the remote control.
– Channels with no stations assigned are ignored.
Note:
Every time you switch stations, the current channel number, the
name of the station, the time, and the titles, start and finish
times of the current and following programmes are shown on
the screen If there is another language or digital audio effects
for the current programme, you will also see this information. In
the »Sound« menu, you can choose the language or the
digital audio effects. Open the »Sound« menu by pressing »F«.
Adjusting the volume
You cannot change the volume in menu mode.
1Adjust the volume by pressing »Ǹ« or »Ƿ«.
– A volume scale is shown on the television screen.
Note:
Volume changes adjust the audio signals at the »TV«, »VCR«
and »L AUDIO R« sockets on the digital receiver.
RadioTV
BASIC FUNCTIONS______________________________

20
Muting the sound
1Press »d« on the remote control to mute the sound.
2Press »d« on the remote control to switch the sound on again.
– You can hear the sound at the volume previously set.
Selecting stations from lists
You can select stations from various lists (e.g. TV stations, favourites).
1Press »OK« to open the station list.
– The most recently activated station list appears.
2To change the station list, press »?« and press »P-« or »P+« to
select the list you want.
3Press »Ǹ« or »Ƿ« to scroll through the lists.
4Press »P-« or »P+« to select the station and press »OK« to call
it up.
5Press »i« to quit the station list.
Switching from the current station to the
previous one
The digital receiver remembers the station which was last selected,
provided it was selected for at least one second.
1Press »z« to switch from the current station to the previous one.
2Press »z« to switch back to the current station.
Note:
You can only switch over when no menu is shown on the screen.
BASIC FUNCTIONS ______________________________________