GSD Smart Slave Instruction Manual

Installation & User Manual V1.1
No.1 Turnpike Business Park,
Ballymount,
Dublin 22, Ireland.
Telephone: [phone].
Fax: [phone].
2
Technical Specification
Contents
3
Output Data format
4
Installation Diagrams
6
Wiring Diagram
Smart Slave
Other products from GSD
standalone products
GSD also offers fully functional standalone door controls for less complex door
management. This attractive design, with modern aesthestics, will complement
any building
- GSD Digital Keypad
- GSD Proximity Switch
- GSD Pin&Prox Switch
- GSD Biometric Switch
Features:
50 users
Access control
Door Monitoring
Manager User
Fire and Intruder alarm interface
Backlighting
Tamper resistant
5 amp relays
Indoor or outdoor use
Robust polycarbonate housing with stainless steel keys
Mounts onto a standard electrical back box

2Technical Specifcation
Power Supply 12V DC
Current consumption 70mA
Current consumption with load (max) 100mA
Relay Contact Rating 5 Amps /240V ac
Operating Temperature -20 C to +60 C
Moisture Resistance IP 67
Max Data Cable Length - ( Shielded ) 100m
Dimensions - Flush Mount W. 87mm D. 21mm H. 119mm
- Surface Mount W. 87mm D. 35mm H. 119mm
Technical Specs
Adding a Programming Card
AnyCard
x 2
Step Description
1 Remove security caps and power down unit.
Power up unit and Present Any Card 2 times
2 immediately. This card is now the Programming
Card for the unit. Refit security caps
Default Data Output Format
The Default Data Output Format is set to Clock and Data Format
On power-up the Data Output Format can be determined by the number of beeps:
- 1 beep = Wiegand 26 bit Format
- 2 beeps = Wiegand 34 bit Format
- 3 beeps = Clock and Data Format
The Data Output Format can be changed by following instructions on page 3.
3
Output Format
Output Data Format - Wiegand 26 bit
Step Description
1 Present Programming Card 1 Time
2 Present Any Card once
Programming
Card x 1
AnyCard
x 1
Output Data Format - Wiegand 34 bit
Step Description
1 Present Programming Card 2 Times
2 Present Any Card once
Programming
Card x 2
AnyCard
x 1
Output Data Format - Clock and Data
Step Description
1 Present Programming Card 3 Times
2 Present Any Card once
Programming
Card x 3
AnyCard
x 1

4Installation Diagrams
When Surface Mounting the Door Control
a Surface Mount Collar is required.
- Fix Surface Mount Collar to
wall, ensure arrow is
pointing upwards
After fixing Surface Mount Collar to wall
(as above) and wiring is complete as per
wiring diagrams on pages 6-11, the Door
Control may then be screwed to
Surface Mount Collar using
security screws provided.
Both Security Caps are
then clipped onto the Door
Control.
To attach Security Caps: Simply
align the tabs into holes and push
on until click is heard.
Surface Mounting
Security Caps
5
Installation Diagrams
To release Security Caps push a
screwdriver into slots on the side
and pull forward.
Door Control is mounted to electrical pattress box using security
screws provided. Both Security Caps are
then clipped onto Door Control.
Flush Mounting
To attach Security Caps: Simply
align the tabs into holes and push
on until click is heard.

7
Wiring Diagram
12V Linear
Power supply
6Wiring Diagrams
Wi-Smart
(See manual for detailed
wiring diagram)
Data1/Clock OutputData0/Data Output
Tamper Alarm Output
12V DC
Only
0V
Buzzer Control Input
Green LED Input
Red LED Input
Card Present Output
Max Data Cable Length
- 100m Shielded Cable
Common the OV from the
Smart Slave and the OV
from the Door Control to
avoid any ground loop issues.
Installation Notes