GVA GVAOC3311TH User manual

Instruction Manual
11 Fin Turbo Oil Column Heater
/ GVAOC3311TH

General Care and Safety Guide
Thank you for choosing a GVA Oil Heater. This GVA Heater has been
designed and manufactured to high standards of engineering and with
proper use and care, as described in this leaflet, will give you years of
useful service. Please read these instructions carefully.
TECHNICAL SPECIFICATION
Model No:GVAOC3311TH
Supply:220-240VAC 50Hz
Wattage: 2400W
1. Use only the voltage specified on the rating label
of the appliance.
2. Keep all objects at least 1 metre from the front,
sides and rear of the appliance. Do not place
appliance close to radiant heat source.
3. Do not operate in areas where petrol, paint or
other flammable liquids are used or stored.
4. Do not insert or allow foreign objects to enter
any ventilation or exhaust opening, as this may
cause an electric shock, fire or damage to the
appliance. Do not sit on the appliance.
5. Do not operate this appliance with a damaged
cord, plug or after the appliance malfunctions or
has been dropped or damaged in any manner.
Return to a qualified electrical person for
examination, electrical service or repair.
6. This appliance is intended for household use
only and not for commercial or industrial use.
7. Use this appliance only as described in this
manual. Any other use is not recommended by
the manufacturer and may cause fire, electrical
shock or injury.
8. The common cause of overheating is deposits of
dust or fluff in the appliance. Ensure these
deposits are removed regularly by unplugging
the appliance and vacuum cleaning the air vents
and grills.
9. Do not use abrasive cleaning products on this
appliance. Clean with a damp cloth (not wet)
rinsed in hot soapy water only. Always remove
plug from the mains supply before cleaning.
10. Do not connect the appliance to mains supply
until completely assembled and adjusted.
11. Switch off and use handles provided when
moving.
12. Do not operate with cord set coiled up as a heat
build up is likely, which could be sufficient to
become a hazard.
13. Do not use an extension cord, powerboard, or
external timer with this unit.
14. Do not remove plug from power socket until the
appliance has been switched off.
15. Do not remove plug from power socket by
pulling cord; always grip plug.
16. Always unplug appliance when not in use.
17. Do not locate the heater directly below any
power socket during operation.
18. Do not twist, kink or wrap the cord around the
appliance, as this may cause the insulation to
weaken and split. Always ensure that all cord
has been removed from any cord storage area
and is unrolled before use.
19. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge, unless they are
supervised or have been given instruction
concerning the use of the appliance by a
person responsible for their safety.
20. Do not use this appliance in the immediate
surrounds of a bath, a shower, or a swimming
pool or other liquids. The appliance must not
be immersed in any liquids.
21. When the appliance has been unpacked,
check it for transport damage and ensure all
parts have been delivered. If parts are missing
or the appliance has been damaged, contact
the GVA Customer Services Team.
22. If your appliance does not work, or is not
working properly, contact the place of
purchase or the GVA Customer Services
Team. Repair work on the appliance by
unqualified persons can cause serious risk to
the user.
23. There are no user serviceable parts installed in
the unit.
24. Do not place the unit in wardrobes or other
enclosed spaces as this may cause fire
hazards.
25. This unit is not supposed to be used in or
around locations where foodstuffs, works of art
or delicate articles of science, etc are stored.
26. Indoor use only.
27. Children should be supervised to ensure that
they do not play with the appliance.
28. Ensure heater is on a flat, stable, heat-
resistant surface.
29. It is important that you do not cover this
heater.

Always choose a safe location for the heater, keeping in mind the safety
precautions outlined. Ensure all packaging has been removed from the
unit before use. This appliance requires no installation, it should be used
solely as a portable appliance.
WARNING Keep all objects at least 1 metre from
the front, sides and rear of the appliance.
PLEASE NOTE: As this product is fitted with a
Timer, the Timer has been set to the “ON”
position. Please refer to the Timer section for
setting instructions.
ASSEMBLY OF THE HEATER
Turn the heater upside-down on a non-scratching
and stable surface. Be careful to prevent damage
to the paint finish or your floor surfacing.
Fit the wheel castors onto the radiator by placing
the U-shaped bolts between the outermost fins on
each side of the radiator. Screw the wing nuts onto
the U-shaped bolt and fasten the wing nut securely.
HEAT CONTROL SWITCH
The control switch positions are:
I - Low heat
II - Medium heat
III - High heat
Check that the Heat Control Switch is set to Off
position before plugging the heater into the mains
supply. For greater economy, use the High Heat
setting initially and then switch to the Low Heat
setting.
THERMOSTAT
Turn the thermostat knob clockwise until the
maximum temperature is obtained on the
graduated scale. When the desired room
temperature is reached, slowly turn the knob anti-
clockwise until the heater turns off (you will hear a
click). The heater will now cycle on and off to
maintain the set temperature.
TURBO/CERAMIC HEATER
The Turbo function is for supplying heat instantly
whilst the main heater warms up. For Turbo heat,
switch the Turbo ON/OFF using the switch on the
front of the turbo cover.
Do not use this heater with a programmer, remote-
control system , separate timer or any other device
that switches the heater on automatically.
CAUTION: The heater generates heat during use.
Proper precautions must be taken to prevent the
risk of burns, scalds, fires or other damage to
persons.
PROOF OF PURCHASE
To receive warranty retain receipt as proof of
purchase. (Refer to back of booklet).
IMPORTANT! NEVER COVER THIS HEATER!
SAFETY DEVICE
This appliance has three protection devices:
The first device will automatically turn the appliance
off if the appliance is not in the appropriate
operating position.
The second device automatically disconnects &
reconnects the appliance at apre-set temperature.
The third device disconnects the appliance
permanently in case of overheating, by means of a
thermal fuse (it is non resettable).
Operating Your Oil Column Heater

Indicates actual
time
“ON”button
“TIMER”button
“OFF”button
Mode Switch
TIMER
Set the MODE switch to the Timer position (this
function can only be used once a heat level has
been selected (see thermostat, power settings).
You must set the time prior to programming the
Timer. To do this; turn the outer dial of the timer in
a clockwise direction until the time of the day (24-
hour clock) corresponds with the triangular
marking. Example if it is 2pm (1400 hours) then set
the triangular mark in line with 14. One complete
turn of the dial corresponds to 24 hours.
There are 96 “riders”, positioned around the dial,
each rider represents 15 minutes.
Where all the “riders” are pushed to the outside of
the timer the heater will be ON continuously.
To set a specific time for example:
If you want the heater to be on from 6pm to 10pm,
then set all the riders from 18 to 22 (1800 hours to
2200 hours) to the outside of the rim and all other
riders to the inside of the timer. The unit will then
turn on automatically at 6pm and off again at 10pm.
WARNING! Take care in positioning your heater,
using the timer will mean the heater will come on
automatically. Fire may result if placed next to
combustible material.
Operating Your Oil Column Heater
CARE AND CLEANING
The heater requires regular cleaning to ensure
trouble free operation:
Unplug the heater from the mains supply before
cleaning.
Ensure that the heater has been allowed to cool
down completely before cleaning.
Use a damp cloth (not wet) to wipe the exterior of
the heater to remove dust and dirt.
Never use solutions such as benzene, thinners or
polishing agents.
Use a vacuum cleaner to remove dust and fluff
from around the grills and fins.
Ensure the heater is dry before plugging back into
the mains supply.
Do not attempt to dismantle the heater. There are
no user serviceable parts. For service or repair,
contact an authorised electrical service technician.