GW Instek GPM-001 User manual

Power Meter Test Fixture
GPM-001
USER MANUAL
GW INSTEK PART NO. 82PM-00100MB1
ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without prior
written consent of Good Will company.
The information in this manual was correct at the time of printing.
However, Good Will continues to improve products and reserves the rights
to change specification, equipment, and maintenance procedures at any
time without notice.
Good Will Instrument Co., Ltd.
No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

1
INTRODUCTION
The GPM-001 power meter test fixture is an
accessory designed by GW Instek for applying to the
GPM-8213 and GPM-8310. It was designed for
customers to handy use the four measurement
terminals on the front panel of the GPM-8213 to test
products, which eliminates the need for repetitive
wiring as well as the trouble caused by wiring.
Package Contents
Check the contents before using the instrument.
Contents
Main unit
Test leads (red x2,
black x2)
GTL-213 (blue x1,
yellow x1)

2
Dimensions

3
Appearance
Front Panel
Upper Panel
Power Switch
AC power output
(universal socket)
AC power output
(EU socket)
Rear Panel
Current measurement
terminals
Voltage measurement
terminals
AC power
input socket
Grounding
terminal

4
CONNECT THE FIXTURE
Use the GPM-001 power meter test fixture to perform
the AC input power consumption test of product.
Connect the GPM-001 in series to the DUT and the
mains. The wiring method is related to the test
accuracy. Two kinds of wiring methods are suggested
as below.
Wiring method of GPM-8213
When measuring
a larger current
Connect the voltage measurement terminal to the side
of the load. Please use V+2 and V-terminal as voltage
measurement terminals and I + and I- terminal as
current measurement terminals.
Connection

Power meter
Power supply Product under test
A
V
N
L
Power loss = (Input voltage[V])2/2.4MΩ
Note
When switch is on and, without DUT wired, namely
no load, V+2 and V- terminals are well connected, a
current value, which is calculated by “Input
Voltage/2.4MΩ”, will be generated.

5
AC 10A
CURRENT VOLTAGE
I
MAX
I
V
V
AC 600V
MAX
CAT II 300V
When measuring
a smaller current
Connect the voltage measurement terminal to the side
of power supply input. Please use V+1 and V-terminal
as voltage measurement terminals and I + and I-
terminal as current measurement terminals.
Connection
Power meter
Power supply Product under test
A
V
N
L
Power loss = (Input current[A])2 x 500mΩ
AC 10A
CURRENT VOLTAGE
I
MAX
I
V
V
AC 600V
MAX
CAT II 300V

6
Wiring method when using the test fixture
When using a fixture, there is no need to destroy the original plug. The
wiring method is really simple and details steps are described as below.
Steps
1. Insert the input terminal of DUT to the AC
universal socket of the GPM-001 power meter test
fixture.
2. The voltage terminal and the current terminal will
be assigned automatically from the AC socket
through the GMP-001 power meter test fixture.
Connect the voltage and the current terminals of the
fixture to the corresponding input terminals on the
front panel of the GPM-8213 with test leads.
3. Connect AC power to the AC outlet on the rear
panel of the GPM-001 power meter test fixture.
4. Turn on the AC power switch on the front panel of
the GPM-001 power meter test fixture to start
testing.

7
Wiring method of GPM-8310
When measuring
a larger current
Connect the voltage measurement terminal to the side
of the load. Please use V+2 and V-terminal as voltage
measurement terminals and I + and I- terminal as
current measurement terminals.
Connection

Power meter
Power supply Product under test
A
V
N
L
Power loss = (Input voltage[V])2/2MΩ
Note
When switch is on and, without DUT wired, namely
no load, V+2 and V- terminals are well connected, a
current value, which is calculated by “Input
Voltage/2.4MΩ”, will be generated.
When measuring
a smaller current
Connect the voltage measurement terminal to the side
of power supply input. Please use V+1 and V-terminal
as voltage measurement terminals and I + and I-
terminal as current measurement terminals.
I I
20A MAX
CAT II 600V
CURRENT V
VOLTAGE
V
600V MAX
EXT1
EXT2
10V MAX
2V MAX

8
Connection
Power meter
Power supply Product under test
A
V
N
L
Power loss = (Input current[A])2 x 505mΩ
I I
20A MAX
CAT II 600V
CURRENT V
VOLTAGE
V
600V MAX
EXT1
EXT2
10V MAX
2V MAX