Häfele 836.21.351 Installation manual

1
CLOSET SAFE
Programming Instructions
Item No.: 836.21.351
NOTE
The Safe Ships with a set of “Emergency Keys” used to gain access to safe if locked out.
DO NOT place these emergency keys inside the safe!
SPECIFICATIONS:
Weight: 31 lbs.
Width: 16”
Depth: 13” (Including Keypad)
Height: 11-7/8”
INSIDE DIMENSIONS:
Width: 15-1/2”
Depth: 10”
Height: 11-1/2”
FEATURES:
• Designed to fit within 18” wide opening
• Electronic Keypad lock with 3-6 Digit Code
• Motorized Locking Bolts
• Emergency Keys (2) allow access if battery or code is lost
• Master Code Option
• Mounting holes provided to anchor securely to wall or shelf
• Steel Thickness: Safe Body 2 mm, Safe Door 4 mm
• Four (4) AA Batteries Required (Not Included)
• Black Powder Coated Finish
VALUED CUSTOMER,
Thank you for choosing our Closet Safe! You’ve taken an important step in organizing and protecting your
most valued possessions within your Closet. This safe is professionally made and designed to provide safety.
Please take time to read and familiarize yourself with the proper operating procedures of your new safe
presented on the following pages.

2
3901 Cheyenne Drive • Archdale, NC 27263
1-800-423-3531 • www.hafele.com/us
BATTERY
• The working voltage for the product is equal to 4 AA batteries (Not Included).
• System will turn into micro power consuming state automatically.
TEST BATTERY VOLTAGE
Press the “#” key, if the display reads “BA—H”, it
means the batteries are normal; if the displays reads
“BA—L”, it means the voltage are low and must be
replaced as soon as possible.
CAUTION
When replacing batteries, replace ALL the
batteries at once and never use or mix old
and fresh batteries together.
SETTING THE PERSONAL CODE
• Enter the factory default code 1 2 3 4 the
LCD display will indicate “opened”.
• With door opened, enter any 3-6 digit code you
wish to change code to be.
• Press “**”, screen displays “CLOSED”, which means
the door is closed.
• The screen will show the new code entered, which
means your new code has been accepted
• You can now open the door by your new code.
SETTING THE MASTER CODE
• Press “**” when the door is open, the display
reads “PROG”.
• After “PROG” disappears, enter preset master code
(The factory master code of hotel mode is “011223”)
and reading “NEW”.
• After “NEW” disappears, input your new code
(6 digits) within 5 seconds, the display will
read “AGAIN”.
• After “AGAIN” disappears, input your new code
(6 digits) again within 5 seconds, then the display
reads “DONE”,
• New master code setting is successful, if the display
reads “ERROR” process will need to be restarted
SECURITY FUNCTION:
HIDE THE CODE WHEN TYPING
Press “*” before enter code, and the display will NOT
show your CODE as you type it and will not show/display
back the code you entered when the door locked.
AUTOMATIC LOCK (DELAY)
After four (4) consecutive times of error codes, the
system will be locked out automatically. During that
time, the display will display “HOLD15” every press.
15 minutes later, the system will start again, allowing
keypad entry.
OPENING THE SAFE WITH “EMERGENCY KEYS”
If the electronic lock circuit has malfunctioned, or
battery is dead, or codes unknown. You can open
the safe using the Emergency Keys supplied.
• Open the black plastic cap on the front of the
safe (door)
• Insert the emergency key and turn clockwise
to OPEN
Note
If you have LOST The Emergency Keys Contact
Reseller where safe was purchased for other options.
ERROR INDICATION
When screen displays the following indications, it
means there are errors. Please operate according to
the following instructions.
• ERROR—means the code is incorrect and you
need to enter correct code.
• ERROR1—means the door can not be open
normally, and the bolt is blocked. Please push the
door slightly to loosen the bolt.
• ERROR2— when the locking bolts are blocked
preventing them from extending. Remove
obstruction and lock door.