hager Muse WGMS113SUSBKB User manual

www.hager.com
Safety instructions
Electrical equipment must only be installed and assembled by a qualified electrician in
accordance with the relevant installation standards, regulations, directives and safety
and accident prevention directives of the country.
Failure to comply with these installation instructions may result in damage to the
device, fire or other hazards.
Function
The device combines a BS socket outlet with a single/twin USB port charging unit.
ON/OFF
switch
2 USB
ports
ON/OFF
switch
USB
port
Switched socket with 1 USB Switched socket with 2 USB
Socket features:
The BS socket outlet is compatible with BS 1363-1 plugs. It can be switched ON/OFF using
the integrated single pole switch.
USB features:
- The USB port charging unit is suitable for charging most portable electronic devices con-
nected via a USB type A plug.
- It is supplied independently of the ON/OFF switch position.
- With dynamic load recognition
- Short-circuit proof and overload proof
Correct use
- For the flush-mounted installation in standard wall boxes
(recommended wall box depth ≥ 35 mm).
- Only suitable for use in indoor areas with no drip and no spray water.
13A single switched socket + USB
Hager Muse Installation manual

2
Charging portable electronic devices
Insert USB type A connector of the charging cable into one USB charging port.
Only for “2 USB” version: Two portable devices can be charged simultaneously with a
maximum total charging current of 2.4 A. The charging current split is determined by the
devices to be charged.
CAUTION!
Use only approved charging cables and connectors.
ç
If the charging process is complete or shall be interrupted, plug out charging cable.
Technical data
Rated voltage: 220 ... 240 V~
Frequency: 50/60 Hz
Socket rated current: 13 A
Switch type: single pole
Conductor cross-section of screw terminals: min. 1 x 1.5 mm² ... max. 2 x 4 mm²
Distance of fixing holes: 60.3 mm
Socket compliance: BS 1363-2 and SS 145-2
USB output: 5 V d.c.
USB output current: max. 2.4 A
Standby power consumption of USB unit: < 150 mW
USB compliance: IEC 62368-1
Operating temperature: -5 ... +45°C
Relative humidity (no condensation): 0 % ... 95%
Information for electricians
Installation and electrical connection
DANGER!
Touching live parts can result in an electric shock.
An electric shock can lead to death.
Disconnect the connecting cables before working on the device and cover
all live parts in the area!
ç

3
Preparing the device for installation (example “2 USB” version)
The device is delivered with a transparent dust protection sticker. This sticker must remain on
the device during the time of installation.
Frame
1
Notch
Carefully loosen the frame on the notch with a flat-blade screwdriver or similar tool.
Lift up and remove the frame (1).
Connecting the device
E
N
L
2
Strip connection cables approx. 10 ... 12 mm.
Wire the device according to the connection diagram (2).
Installing the device into the wall box (example “2 USB” version)
3
After wiring, fix the device with the two screws attached into the wall box (3).

4
Assembling the frame
Frame
4
Snap the frame onto the device (4).
Remove the dust protection sticker.
Preparing the device for insulation resistance testing
WARNING!
To avoid possible damage to the product or spurious insulation readings,
please DISCONNECT the USB charging unit before carrying out insulation
resistance testing (see figure below)!
ç
Before insulation resistance testing
Remove the frame.
Insert a flat-blade screwdriver into the small hole next to the tool symbol and open the lid.
The USB charging unit is disconnected.
After insulation resistance testing
Click
After insulation resistance testing, close the lid until it clicks into place.
The USB charging unit is reconnected.
Snap the frame back onto the device.