hager coviva Smartbox TKP100A User manual

Page 1/45
installer_07-2017
Mounting and conguration instructions
hager.com
coviva smartbox
coviva smartbox
TKP100A
WLAN stick
TKH180
Power supply (replacement
requirement)
TKC110

Page 2/45
installer_07-2017
Inhalt
Safety instructions ......................................................................................................................4
Design and layout of the device.................................................................................................4
Scope of delivery ......................................................................................................................................................4
Optional accessories ................................................................................................................................................5
Function .......................................................................................................................................5
System information...................................................................................................................................................5
Correct use ...............................................................................................................................................................6
Product characteristics .............................................................................................................................................6
The Project Process....................................................................................................................7
1 Preparations.............................................................................................................................7
Role concept.............................................................................................................................................................7
myHager account......................................................................................................................................................7
Install coviva mobile-App..........................................................................................................................................8
Call up coviva web app.............................................................................................................................................8
The rst Login...........................................................................................................................................................9
2 Installation and commissioning...........................................................................................10
Selecting installation location..................................................................................................................................10
Setting up/mounting device ....................................................................................................................................10
Connect device to the LAN using a cable...............................................................................................................11
Connect device wirelessly to WLAN.......................................................................................................................12
3 Conguration.........................................................................................................................13
Congure access for (mobile) end device ..............................................................................................................13
Congure separate hotspot via WLAN stick ..........................................................................................................13
Create a new project ..............................................................................................................................................14
Update device software .........................................................................................................................................16
Congure WLAN integration of the device .............................................................................................................17
Add device to the project ........................................................................................................................................17
Add Netatmo weather station ............................................................................................................................18
Add Comfort device ...........................................................................................................................................18
Edit/remove device .................................................................................................................................................19
Combine devices into groups .................................................................................................................................21
Edit/remove group ..................................................................................................................................................23
Create covigram .....................................................................................................................................................25
Example 1: Temperature warning: .....................................................................................................................25
Example 2: Outdoor lighting:..............................................................................................................................27
Example 3: All OFF: ...........................................................................................................................................28
Edit/remove covigram.............................................................................................................................................30
Add device to the favourites list..............................................................................................................................32
Remove device from the favourites list...................................................................................................................32
Add user .................................................................................................................................................................33
Edit/remove user.....................................................................................................................................................34
Change settings......................................................................................................................................................34
4 Project handover ...................................................................................................................37
Hand over project ...................................................................................................................................................37
hager.com
coviva smartbox

Page 3/45
installer_07-2017
Operation....................................................................................................................................38
Operating concept ..................................................................................................................................................38
Carrying out a reset ................................................................................................................................................41
Carry out a network reset...................................................................................................................................41
Carry out a user reset ........................................................................................................................................42
Carry out rest to factory settings ........................................................................................................................42
RGB LED display....................................................................................................................................................42
Remote maintenance ................................................................................................................43
Appendix ....................................................................................................................................44
User proles and rights ............................................................................................................44
Technical data............................................................................................................................44
Accessories ...............................................................................................................................45
hager.com
coviva smartbox

Page 4/45
installer_07-2017
Safety instructions
Electrical equipment may only be installed and assembled by a qualied installer in ac-
cordance with the relevant installation standards, guidelines, regulations, directives,
safety and accident prevention regulations of the country.
Failure to comply with these installation instructions may result in damage to the device,
re or other hazards.
Design and layout of the device
(1)
(10)
(9)
(8)
(7)
(6)
(5)
(12) (13) (14)
(15)
(16)
(11)
(4)
(2)
(3)
ONLINE
WLAN
POWER
005587...
GC03/16
Figure 1: Rear/side view and accessories
(1) RGB LED display
(2) USB connection sockets
(3) RJ45 connection socket (LAN)
(4) Connection power supply
(5) QR code with coviva ID
(6) Operation LED POWER
(7) WLAN Display - only active with optional WLAN stick (see Accessories)
(8) Status display ONLINE
(9) Acknowledge button OK
(10) Button RESET
(11) Protective cover
Scope of delivery
–coviva smartbox
–Adapter plate for wall mounting (12)
–Power supply 230 V~/5 V (13)
–RJ45 connection cable, Cat 5e (14)
hager.com
coviva smartbox

Page 5/45
installer_07-2017
Optional accessories
–WLAN stick (15)
–WLAN adapter1) (16)
Function
System information
The coviva smartbox forms the interface of wirelessly communicating devices such as KNX
radio actuators or Twin Band devices and WLAN as well as IoT applications to the existing IP
infrastructure via a network router. Electrical loads and functions of the building control can be
interlinked, visualised, monitored and operated on mobile end devices or stationary computers
by means of a mobile app or browser-based web app. In this way, location-independent access
to the building management system - via the home network and via the Internet - can be en-
sured and at any time.
This solution is especially designed for implementing smart Home functions and comfort in mod-
ernised or retrotted systems.
Local access
Building control
Internet
mobile-App Web-App
Global access
1)
1)
WLAN/IoT Mobile communications Radio (KNX radio, TwinBand)
Figure 2: Application environment
1) Not available in every country.
hager.com
coviva smartbox

Page 6/45
installer_07-2017
Lighting
Web-App
mobile-App
Light- and
sun protection
Temperature
control
Security
devices Extension
Figure 3: System overview
Correct use
–Interface for wireless communication with receivers/actuators via the IP network
–Operation and visualisation on (mobile) end devices via coviva app
–Connection to the network router by cable or via optional WLAN stick (see Accessories)
–The device is only suitable for indoor areas.
Product characteristics
–secure system administration via user proles with different rights
–control of quicklink radio systems and WLAN applications via mobile app for mobile end de-
vices or web app for notebook, PC, …
–simple creation of scenes (covigrams) via the app
–self-congurable messages after events
–remote access and remote maintenance via integrated Dyn DNS service
–Logic operations
–Updates with notications available online
hager.com
coviva smartbox

Page 7/45
installer_07-2017
The Project Process
Prepare the smartbox in three steps for project handover to the customer:
myHager
coviva
i
my devices
my groups
my covigrams
my favorites
1 Preparations 2 Installation 3 Conguration 4 Project handover
1 Preparations
Role concept
User proles with different access rights must be managed in the smartbox:
User prole Access rights myHager ac-
count
Example
Installer during the project
- unlimited rights
after the handover, if required:
- Remote access after release
by the administrator
Required Installation engi-
neer, planner
Administrator for one user per smartbox:
- Conguration rights for
adding/removing devices
- Administration of all users
Required Home
administrator
User name normal rights for adapting and
operating the system
not required Family members,
fellow occupants
Table 1: User proles
Detailed information on the access rights per user prole can be found in an overview table
in the appendix.
myHager account
In order to create a project with the smartbox, a successful registration Table 1 under hager.
com is necessary. Registration only has to be carried out once prior to the rst coviva project.
The same myHager account has to be used for all further coviva projects.
Go to the hager.com website and click on register now.
Or:
Scan the QR code with an appropriate app, switch to the coviva
hager.com/coviva
homepage and select Registration.
Fill out the personal data, agree to the use of personal data and congure
account with Send.
An e-mail with a conrmation link for activating the myHager account will
be sent to you (Figure 4).
Click the Complete registration button in the
e-mail to activate the account
Later, you can also view completed coviva projects via the account (Figure 5).
hager.com
coviva smartbox

Page 8/45
installer_07-2017
Send
I agree that the personal data given here may be
combined, processed and used with other personal data
that you have about me so that you are able to present
products and solutions to me that tailored specifically to
my requirements and interests. Please read on here
Yes, please send me newsletters to inform me of new
products, services and software updates from Hager
Vertriebsgesellschaft.
* Mandatory fields
Newsletter
Consent *
[phone]
United-Kingdom
Telford, Shropshire
TF1 7FT
Hortonwood 50
Hager Ltd.
97.11.1969
Business address *
DD.MM.YYYY
Business address Private address
Company *
Street / house number*
Postal Code*
Place*
Country*
Phone
Mobile phone no.
Hager Ltd.
Welcome to coviva!
Your electrician has set up your coviva Box
for you.
To benefit from the full range of functions
supported by your connected home, you
will need a myHager account.
You can create a myHager account easily
for my[email protected] right now:
Complete registration
Input (265)
Figure 4: myHager account
Install coviva mobile-App
Log in to the corresponding app store on the mobile device and select the coviva app.
Download and install app.
The app requires at least version IOS 7.1 or Android 4.1 or higher on the mobile
end device.
The IOS app is optimised for iPhones. iPad users must use the iPhone only setting when
running searches in App Store
Call up coviva web app
As an alternative to the mobile app, it is also possible to access the smartbox after project hand
over via a web portal from a PC, notebook or mobile end device with a Windows operating
system. An HTML5 compatible browser such as Chrome, Safari, Internet Explorer or Firefox is
required. The user interface is similar to the coviva mobile app and provides the same functions
in a suitable format for larger screens.
The web app can rst be used after handing over the project to the customer(Administrator),
such as for remote maintenance. It is not suitable for conguration by the installer.
Enter the URL customised with the ID: https://12-diget coviva ID.koalabox.net/webapp in the
browser.
The web app opens.
The web app can also be called up in this way:
Log into the myHager account and select My coviva projects.
Open the web app via .
The end device and smartbox must be online each time the web app is subsequently used.
Installation engineer'sCustomer's e-mail address
coviva: Intelligent retrofit wireless technology
0024C6F21834 my[email protected]
Your coviva installations
My account
My software
My coviva
Installations
With the wireless coviva system for smart
homes, you are oering your customers a
solution for an intelligent home. Ideal for retrofit,
renovation or modernisation projects.
Learn more now!
ID
[email protected]
Figure 5: myHager project view
hager.com
coviva smartbox

Page 9/45
installer_07-2017
The rst Login (Figure 6)
The (mobile) end device is online.
Open the coviva app .
Switch with to login as an installer.
Enter e-mail address and password of the myHager account and log in with Login.
The access data is validated online against the myHager account. A message conrms the
successful Login.
Welcome to coviva !
The unique ID on the rear of your
coviva controller connects you directly
to your coviva
Login
Test without login
coviva ID
myHager ANB
In order to use the coviva app, you
must accept the general terms and
conditions of use for your myHager
account. Please press the
“myHager ANB” button to continue
General terms and conditions...
Q W E R T Y U I O
A S D F G H
Z X C V B N M
J K L
P
Login
[email protected]
myHager
E-Mail (User name)
Password
[email protected]
return space .?123
Terms of use
Please confirm the terms and conditions of use
for your coviva Smartbox.
Personal data
coviva terms and conditions of use *
I accept the coviva terms and
conditions of use of dated 31/01/2017.
*Mandatory fields
Hager Ldt.
Save
Hager Ltd.
Publication details Data privacy Cookie policy
Terms of use
Please confirm the terms and conditions of use
for your coviva Smartbox.
Thank you
We have saved your consent in your myHager
account.
Please now re-open the coviva app on your
smartphone or tablet, navigate back to the login
form and enter your myHager password again.
You should be able to activate the app
immediately.
Hager Ltd.
Publication details Data privacy Cookie policy
Hager Ltd.
Figure 6: First Login
If the General Term of Use (GToU) for the coviva app have not yet been accepted in the my-
Hager account, the corresponding web page must be accessed at this point.
To do this, press the myHager GToU button.
Accept the GToU via the checkbox and complete the operation via Save.
Afterwards, log in again to the app.
hager.com
coviva smartbox

Page 10/45
installer_07-2017
2 Installation and commissioning
CAUTION!
Excessively high voltages can impair the functionality of the device!
Operation on an unsuitable power supply can damage the device.
Only use the power supply provided for supplying power to the device.
ç
Selecting installation location
The smartbox can basically be set up anywhere in the house or mounted on a wall if a power
supply socket outlet and LAN connection (router or FCC socket outlet) are accessible with the
cables provided. During integration into the network via the optional WLAN stick (see Accesso-
ries) make sure that the WLAN connection to the router is stable.
Since the smartbox communicates via radio signals, extreme care must be taken to ensure that:
–the device is positioned as centrally as possible.
–a minimum distance of approx. 1 m is maintained between the smartbox and all receivers.
–there is minimum distance of approx. 0.5 m to electronic devices which emit high frequency
signals such as computers, electronic transformers or microwave devices.
–the device is mounted far from metal surfaces, reinforced concrete or heat sources and
moisture.
–the material penetration is taken into account (Table 2).
The range of the device can be optimised by selecting the best possible mounting location.
Material Degree of material pe-
netration
Wood, plaster, plasterboard, uncoated glass approx. 90 %
Brick, press boards approx. 70 %
Reinforced concrete, underoor heating approx. 30 %
Metal, metal grids, aluminium laminates, coated glass approx. 10 %
Rain, snow approx. 1 ... 40 %
Table 2: Material penetration
Setting up/mounting device (Figure 7)
Set up the smartbox on a level surface.
Make sure that the protective back cover (11) is attached to ensure stability.
Or:
Attach the enclosed adapter plate for wall mounting (12) - vertically on the wall with two
screws - not included. Make sure that the TOP is aligned upwards.
Push down the protective back cover (11) and remove it.
Put the smartbox onto the adapter plate and push downwards until it locks into place in the
adapter plate.
The smartbox can also be set up in a network cabinet with a depth of at least 50 mm. Then,
however, the material with its penetration for radio signals must be taken into account
(Table 2)
hager.com
coviva smartbox

Page 11/45
installer_07-2017
ONLINE
WLAN
POWER
005587...
GC03/16
Figure 7: Set up (top), wall mounting (bottom)
Connect device to the LAN using a cable (Figure 8)
The optimum integration of the smartbox in a network is the cabled connection to a router. This
generally ensures higher transmission rates, more safety and greater reliability.
The cabled connection is therefore strongly recommended during the project process.
Connect the smartbox on the RJ45 connection socket (3) to the LAN/router using the en-
closed connection cable. This can take place directly on an RJ45 connection of the router or
on an FCC socket outlet within the LAN.
Always used the enclosed connection cable Cat. 5e or a network cable of the same category
or higher.
Insert enclosed power supply 230 V~/5 V in the smartbox (4) and connect to a socket
outlet.
The operation LED POWER (6) lights up. The RGB display (1) ashes white while booting
and then goes out. The ONLINE status display (8) lights up white.
hager.com
coviva smartbox

Page 12/45
installer_07-2017
ONLINE
RESET OK
WLAN
POWER
Figure 8: Cabled connection
A connection to the smartbox can now be established with a mobile end device via the WLAN
network.
The rst connection to the smartbox must be established locally at the place of installation
and cannot be carried out by remote access.
Connect device wirelessly to WLAN (Figure 14)
Alternatively, the smartbox can also be integrated in the network of the customer by WLAN. The
optionally available WLAN stick is required for this (see Accessories). This is particularly useful
if the router is not set up at a central location or the smartbox is mounted on a wall and no net-
work connection is in the vicinity.
The wireless connection is a good alternative particularly for daily use at the customer's
premises once the project has been completed.
A WLAN router is used at the customer's premises.
If there is only a LAN router available, the network can be expanded into a WLAN with the
optional WLAN adapter TKH181 (see Accessories).
Insert the WLAN stick into a USB connection socket WLAN (2) and wait until the WLAN dis-
play (7) lights up white permanently.
Only use the WLAN stick listed under accessories. WLAN sticks of other manufacturers are
not compatible.
Congure the WLAN settings (see Congure WLAN integration of the device).
ONLINE
RESET OK
WLAN
POWER
Figure 9: Wireless integration into the network
hager.com
coviva smartbox

Page 13/45
installer_07-2017
3 Conguration
The following descriptions are based on the mobile app in the IOS system. The Android app as
well as the descriptions in the Web app may vary slightly from this, but the functions, buttons
and messages are identical.
Congure access for (mobile) end device
A WLAN router is used at the customer's premises.
If there is only a LAN router available, the network can be expanded into a WLAN with the
optional WLAN adapter TKH181 (see Accessories).
Activate WLAN of the end device.
Log in to the local network of the customer.
Connect end device to the smartbox (see Create a new project).
The end device and the coviva smartbox must be connected to the same local network.
Congure separate hotspot via WLAN stick (Figure 10)
Alternatively, conguration is also possible without access to the WLAN of the customer. With
the optional WLAN stick (see Accessories) a separate network with hotspot can be set up for
the conguration by the smartbox (Figure 10).
Insert the WLAN stick into a USB connection socket WLAN (2) and wait until the Wi display
(7) lights up white permanently.
Select the automatically WLAN network coviva – 12 digit coviva ID in the settings of the
mobile end device.
The successful connection to the smartbox is displayed in the end device.
Only use the WLAN stick listed under accessories. WLAN sticks of other manufacturers are
not compatible.
If the coviva WLAN network is not available, select under and Wi and activate the
Hotspot mode.
A password is not required.
This network can be protected with its own password if required.
Under and , Wi and then select Name.
Give the network its own Name and enter a Password of at least 8 characters.
Conrm the entry with Save.
Once the WLAN network has been changed, this is displayed. The previous WLAN connec-
tion is disconnected.
In the settings of the mobile end device select the WLAN network and enter the new pass-
word.
During both conguration and subsequent continuous operation at the customer's premises,
the smartbox can be operated ofine with the WLAN stick if the Internet connection drops
out or there is no connection available (during work on a construction site), provided the user
is logged in. Only applications which require Internet access, such as remote access and IoT
device, will be unavailable during this time.
hager.com
coviva smartbox

Page 14/45
installer_07-2017
ONLINE
RESET OK
WLAN
POWER
My account
All users
Network
IP adress
The IP adress will show here, as soon
as you connect your coviva controller
via LAN to a router (DHCP)
The status LED of your coviva
controller will turn on when a
compliant wifi extension is installed.
App version {{version}}
Copyright Hager Group 2015
All rights reserved
Settings
coviva
Installer
Wifi
192.168. 0.5
i
my devices
my groups
my covigrams
my favorites
My account
All users
Network
IP adress
The IP adress will show here, as soon
as you connect your coviva controller
via LAN to a router (DHCP)
The status LED of your coviva
controller will turn on when a
compliant wifi extension is installed.
App version {{version}}
Copyright Hager Group 2015
All rights reserved
Settings
coviva
Installer
Wifi
192.168. 0.5
i
coviva
Devices
Groups
Covigrams
Favorites
Logout and Handover
O
O
O
Name
Activate the Hotspot mode if want
your coviva controller to open up its
own Wifi network.
Hotspot mode
coviva-0024C6F21834
Settings Wifi settings
Network
The IP adress will show here, as soon
as you connect your coviva controller
via LAN to a router (DHCP)
My account Installer
All users
The status LED of your coviva
controller will turn on when a
compliant wifi extension is installed.
Settings
IP adress 192.168.178.23
Wifi coviva
App version {{version}}
Copyright Hager Group 2015
All rights reserved
Q W E R T Y U I O
A S D F G H
Z X C V B N M
J K L
P
space return.?123
Name and Password
coviva Hotspot mode
Save
Name coviva
Security
Password 12345678
WPA2
The password has to be at least 8
characters long.
Figure 10: Congure separate hotspot via WLAN
Create a new project (Figure 11)
The (mobile) end device is online.
Open the coviva app .
Switch with to login as an installer.
Enter e-mail address and password of the myHager account and log in with Login Login
(Figure 11).
The access data is validated online against the myHager account. A message conrms the
successful Login.
hager.com
coviva smartbox

Page 15/45
installer_07-2017
If the General Term of Use (GToU) for the coviva app have not yet been accepted in the
myHager account this must be repeated at this point (see The rst Login).
If a previously started project is to be continued, click once again on and select Installa-
tions.
If several projects have already started, all unnished projects appear after selecting Instal-
lations. Select the project to be edited from the corresponding line.
Select New installation to start another new project.
The main menu view opens.
Push down the protective back cover of the smartbox (11) and remove it.
Call up the camera of the mobile end device via and hold it in front of the QR-Code (5) at
a distance of approx. 10 … 15 cm until the ID is displayed in the app.
Or:
Enter the 12-digit coviva ID manually via the keypad of the end device.
Then nish the creation of the new project with Connect.
The coviva app and the smartbox can now communicate with each.
Welcome to coviva !
The unique ID on the rear of your
coviva controller connects you directly
to your coviva
Login
Test without login
coviva ID
i
my devices
my groups
my covigrams
my favorites
Connect
Controller coviva
back
Please connect to your coviva
controller by scanning controller’s
QR-code or typing in your coviva
ID.Make sure that you have access to
the local n...the coviva controller
0024C6F21834
Save
Save later
Add user
Repeat email
Email
Please add the email address of the
Principle user. Use Hager portal
account email address
Connect
Controller coviva
Please connect to your coviva
controller by scanning controller’s
QR-code or typing in your coviva
ID.Make sure that you have access to
the local n...the coviva controller
coviva ID
Q W E R T Y U I O
A S D F G H
Z X C V B N M
J K L
P
Login
[email protected]
myHager
E-mail (User name)
Password
[email protected]
return space .?123
0024C6F21834
GC03/16
Scan
Figure 11: Create a new project
Afterwards, you are requested to enter the e-mail address of the customer (administrator),
with which he created his myHager account.
Enter the e-mail address of the customer (administrator).
To conrm this, enter the e-mail address a second time and nish with Save.
The empty main menu for the conguration opens. The conguration can begin.
The e-mail address of the customer (administrator) can also be entered at the end of the cong-
uration during the handover. The request comes automatically during the project handover, if no
administrator has yet been created.
To do this select Save later.
If the e-mail address of the customer (administrator) is entered incorrectly or if this has to be
corrected, a user reset can be carried out (see Carrying out a reset).
hager.com
coviva smartbox

Page 16/45
installer_07-2017
Q W E R T Y U I O
A S D F G H
Z X C V B N M
J K L
P
Please add the email address of the
Principle user. Use Hager portal
account email address
space return.?123
[email protected]
Save
Repeat email
i
my devices
my groups
my covigrams
my favorites
Please add the email address of
the Principle user. Use Hager
portal account email address
Email
Repeat email
Save later
Save
Add User
Figure 12: Create customer (Administrator)
Update device software (Figure 13)
If a software update is available for the smartbox, this is displayed via a message.
We recommend carrying out the update immediately in order to get new functional improve-
ments and to prevent incompatibilities.
Start the update with Install .
The RGB display (1) of the smartbox ashes during the update. It goes out after successful
completion of the update.
The operation may take a few minutes. If the connection is disconnected during the update,
restore the connection with Retry.
If the update is to be carried out at a later time,
rst decline the update via Later .
Each time the app is subsequently opened, the update will be offered again.
i
my devices
A new update for your
coviva controller is
available. During the
update process the coviva
controller will be not
reachable for some
minutes.
Update available
Install
Later
Figure 13: Software Update for the Smartbox
hager.com
coviva smartbox

Page 17/45
installer_07-2017
Congure WLAN integration of the device (Figure 14)
The WLAN stick is inserted in the smartbox and the WLAN display (7) lights up white perma-
nently (see Connect device wirelessly to WLAN).
Select Wi under and and deactivate the Hotspot mode.
The WLAN networks available within range are displayed.
Select the WLAN network of the customer and enter the WLAN network key.
Finish the entry with Save.
The app reports the successful saving of the WLAN settings. The WLAN stick has had a
new IP address assigned under Settings. This is now from the address range of the custom-
er's home network router.
i
coviva
Devices
Groups
Covigrams
Favorites
Logout and Handover
O
O
O
i
my devices
my groups
my covigrams
my favorites
My account
All users
Network
IP adress
The IP adress will show here, as soon
as you connect your coviva controller
via LAN to a router (DHCP)
The status LED of your coviva
controller will turn on when a
compliant wifi extension is installed.
App version {{version}}
Copyright Hager Group 2015
All rights reserved
Settings
coviva
Installer
Wifi
192.168. 0.5
Name
Activate the Hotspot mode if want
your coviva controller to open up its
own Wifi network.
Hotspot mode
coviva-0024C6F21834
Settings Wifi settings
My account
All users
Network
IP adress
The IP adress will show here, as soon
as you connect your coviva controller
via LAN to a router (DHCP)
The status LED of your coviva
controller will turn on when a
compliant wifi extension is installed.
App version {{version}}
Copyright Hager Group 2015
All rights reserved
Settings
coviva
Installer
Wifi
192.168. 0.5
Settings Wifi settings
Activate the Hotspot mode if want
your coviva controller to open up its
own Wifi network.
FRITZ-Box
Hotspot mode
CHOOSE NETWORK…
Q W E R T Y U I O
A S D F G H
Z X C V B N M
J K L
P
space return.?123
Login
Please enter the password of the
Wifi network
Cancel Client mode
Save
Password
Wifi settings
Settings
Activate the Hotspot mode if want
your coviva controller to open up its
own Wifi network.
FRITZ-Box
Hotspot mode
CHOOSE NETWORK…
Wifi settings succesfully
changed
Wifi
OK
Figure 14: WLAN settings
A connection to the smartbox can now be established with a mobile end device via the WLAN
network.
The rst connection to the smartbox must be established locally at the place of installation
and cannot be carried out by remote access.
Add device to the project
The device types to be integrated into a project are displayed in Figure 3 as an overview. The
devices are categorised according to their technology. Each device must be integrated individu-
ally.
Press the blue button.
The context menu for selecting the device category for the product to be integrated opens.
hager.com
coviva smartbox

Page 18/45
installer_07-2017
You can choose between:
– Connected device
–Security device
–Comfort device (KNX radio actuators/receivers)
The list of compatible products is available under hager.com/coviva.
Add Netatmo weather station (Figure 15)
The weather station (indoor module) has been commissioned and has been registered in the
WLAN network of the customer. The customer has created a Netatmo account.
In the context menu select Connected device.
The view for entering the access data of the Netatmo account opens.
Enter E-mail address and password for the Netatmo account of the customer and nish via
Let‘s go .
The connection setup of the app via the smartbox to the Netatmo account is displayed in the
app. If the connection is successful, Netatmo is displayed.
Activate the line with the description and change the name for the weather station if re-
quired.
Finish the operation with Save or switch to the main menu via Back.
The added device is displayed under my devices .
Carry out the operation with each additional, compatible device until all Netatmo devices
have been added and uniquely named.
Groups
Details
Save
Back
Temperature
Humidity
CO2
Pressure
Sound meter
23,3°C
35%
881 ppm
57dB
1028 mBar
Measurements
Weather station
none
11 23456789
- / : ; ( )
. , ? ! ´
€ & @ “
0
#+=
Let's go
Add a device
space.?123
[email protected]
Adding Netatmo weather station
Enter the user name and password
of your Netatmo account.
return
i
my devices
Off
Off
Off
Comfort device
Wall light living ro...
Ceiling light living
Standard lamp s...
Connected device
Security device
Cancel
What kind of device
would you like to add?
i
my devices
my groups
Off
Off
Off
20°C
Wall light living ro...
Ceiling light living
Standard lamp sofa
Weather station
Lighting first floor
First floor
Figure 15: Add Netatmo devices
Add Comfort device (Figure 16)
Select Comfort device in the context menu.
Switch the app to the conguration mode via Let‘s go.
The app requests that the device to be integrated must be made identiable.
To do this, briey press the fct button on the KNX radio actuator.
The actuator has switched to the conguration mode. The connection setup is displayed in
the app. If the connection is successful, the order number of the device is displayed with an
appropriate symbol.
If there are difculties setting up the connection, a clock is displayed and the attempt is can-
celled with Adding process failed or Time out. Then check in the compatibility list whether
the device can be integrated into the smartbox.
If necessary, activate the line with the order number and give the added actuator(channel) a
name for the application – e.g. ceiling light living.
hager.com
coviva smartbox

Page 19/45
installer_07-2017
Finish the operation with Save or discard via .
The added device is displayed under my devices und its function can be tested directly.
Carry out the operation with each additional actuator(channel) within the KNX radio installa-
tion of the customer until all devices have been added and uniquely named.
i
Security device
my covigrams
my groups
my devices
What kind of device
would you like to add?
Netatmo
Cancel
Comfort device
Let's go
Adding KNX device
1. Press the 'Let’s go' button and
your coviva controller will wait for
compatible devices
2. Now you have to press the
device pairing button
Add a device
Add to Favorites
Groups
none
On
Details
Save
Remove device
Light garden shed_TRE2...
i
Off
Off
Off
my devices
my groups
my covigrams
my favorites
Detector hall
Heating kitchen...
Light garden shed...
... ...
Figure 16: Add Comfort device
Edit/remove device (Figure 17)/(Figure 18)
After adding the devices, they can be edited in the app or removed again at any time.
Press iin the top right corner of the main menu.
Hold the button down for longer if using Android devices.
All elements in the main menu are switched to edit mode.
Select the device to be edited via iin the device list.
Details about the device, such as the switching state or the groups in which it is integrated, are
displayed.
Then implement the following actions as required:
–Change the name of the device by pressing the name line and entering via the displayed
keypad.
–Add device of a Group by activating the checkbox.
–Remove device from a Group by deactivating the checkbox.
–Device Add to Favorites or Remove from Favorites.
–Switch to the delete mode via Remove Device. Then press Remove Device again and
press the fct button on the device to be removed.
hager.com
coviva smartbox

Page 20/45
installer_07-2017
The device is removed from the installation. The app reports Remove Device– Suc-
cessful.The device is no longer displayed in the main menu. It is also removed from all
groups, covigrams and from the favourites list.
Groups
Details
Scene TV
Living
Remove from Favorites
Groups
O
Details
Save
Back
Remove device
Standard lamp sofa_85...
Scene TV
Add to Favorites
Groups
O
Details
Save
Back
Remove device
Standard lamp sofa_85...
Scene TV
Q W E R T Y U I O
A S D F G H
Z X C V B N M
J K L
P
Add to Favorites
Groups
Scene TV
O
Details
Save
Back
space return.?123
Standard lamp sofa_85...
i
my devices
my groups
my covigrams
Off
Off
Off
Wall light living ro...
Living
Scene TV
Ceiling light living
Standard lamp sofa
i
my devices
my groups
my covigrams
Off
Off
Off
Wall light living roo...
Living
Scene TV
Ceiling light living
Standard lamp sof...
Off
my devices
my groups
my covigrams
Off
Off
Wall light living...
Living
Scene TV
Ceiling light livi...
Standard lamp...
Figure 17: Edit device
With the exception of Remove Device nally conrm all edit operations with Save or discard
via Back.
The display returns to the main menu and displays the changes.
Press in the top right corner of the main menu to exit the edit mode again.
hager.com
coviva smartbox