Hakko Electronics FX-1003 User manual

1. Contents and Part Names Conrm the contents before use.
Cleaning wire
Iron cover
Plug
Iron receptacle
Iron holder
Component bed Cleaning brush
Cleaning
sponge
Options
Sold separately
Tip (a set of 2)
Conrm the tip/replacement parts/options on the website.
https://www.hakko.com/
2. Specications This product cannot be used on its own.
Applied tip
400ºC (750ºF) : T38-02 Series
350ºC (660ºF) : T38-03 Series
Heater
IH (High-Frequency
Induction Heating)
Applied
station
HAKKO IH soldering iron
(Conrm details on the
website.)
Cord length 1.3 m (4.3 ft)
Total length
130 mm (5.1 in) (If the
I type tip is attached)
Tip to ground
resistance
<2 Ω Weight 32 g (0.07 lb) (If the
I type tip is attached)
Tip to ground
potential
<2 mV
* The total length and weight excludes the cord.
* This product is applied with electrostatic countermeasures.
* Please note that specications and appearance are subject to change without notice in
the interest of product improvement.
CAUTION
■Handling precautions for ESD Safe products
This product contains electrostatic countermeasures, so please use the following precautions.
1. Not all plastic parts are insulators, they may be conductive. Be careful not to expose live
electrical parts or damage insulating materials when performing repairs or replacing parts.
2. Be sure to ground the product before use.
※各言語（日本語、英語、中国語、フランス語、ドイツ語、韓国語）の取扱説明書は以
下の URL、HAKKO Document Portal からダウンロードしてご覧いただけます。
（商品によっては設定の無い言語がありますが、ご了承ください。）
* 各國語言（日語、英語、中文、法語、德語、韓語）的使用説明書可以通過以下网站的
HAKKO Document Portal 下載參閲。
（有一部分的產品沒有設定外語對應、請見諒）
* Instruction manual in the language of Japanese, English, Chinese, French, German,
and Korean can be downloaded from the HAKKO Document Portal.
(Please note that some languages may not be available depending on the product.)
https://doc.hakko.com
3. Warnings, Cautions, and Notes
Warnings, cautions, and notes are placed at critical points in this manual
to direct your attention to signicant items. They are dened as follows:
WARNING :Failure to comply with a WARNING may result in serious
injury or death.
CAUTION :
Failure to comply with a CAUTION may result in injury to the
operator, or damage to the items involved.
NOTE: This indicates procedures or information that are important
in a process described in this document.
Be sure to observe the following precautions to ensure safety.
WARNING
●
Those without the permission of a manager and those
without the required experience or knowledge (includ-
ing children) are not allowed to use this product.
●Do not allow children to play with this product.
●
Do not allow children to clean or perform user
maintenance without supervision.
●
When this product is not used, place the hand-
piece on the iron holder.
●
The tip reaches high temperatures when the
power source is turned on. You may risk getting
burned or causing a re if mishandled.
Failure to observe the following precautions to ensure safety might result
in electric shock, malfunction or other trouble.
CAUTION
●Before using this product, fully read all descriptions in this document.
●
When connecting the handpiece to the station, do so after turning
the power switch OFF. The station may become damaged.
●When replacing parts, use only genuine HAKKO parts.
●Do not modify this product.
●
Do not use this product with damaged cords or plugs.
Also, if this product is dropped or is damaged in other ways, immedi-
ately stop use of this product.
●
When inserting and removing the cord, hold the plug body and do
not pull the cord.
●
Do not allow this product to get wet. Also, do not handle it with wet hands.
●
Do not perform any other actions that may be considered dangerous.
4. Assembly
(1) Align the tip with the ▲ mark of the angle adjustment wheel and insert
the tip all the way.
Angle adjustment wheel
State where it is inserted all the way
D cut portion
Tip
▲ mark
▲ mark
(2) Place the handpiece on the iron holder.
Tip storing pocket
(4 spots)
Handpiece FX-1003......................1
Iron holder FH-800 .......................1
Cleaning sponge...........................1
Cleaning wire ................................1
Instruction Manual (this document) ....1
MICRO TWEEZERS
FX-1003
Instruction Manual
Thank you for purchasing the FX-1003.
This product is a micro tweezers handpiece that
connects to the HAKKO IH station.
Before using this product, be sure to read this manual.
Keep this manual readily accessible for reference.
取説 FX-1003_EN_210301.indd 1取説 FX-1003_EN_210301.indd 1 2021/03/01 13:19:522021/03/01 13:19:52

5. Operation
CAUTION
●
Since the end of the tip is thin, handle it carefully. If the tips and pipes
are bent, they may not be aligned properly even if they are adjusted.
●
When attaching/removing the tips, be sure to turn the power source OFF.
5-1 Handpiece
Adjust the positions of the tip ends with 4 wheels.
Afteradjustmentsaremade,closethetipsandconrmthepositions
of the tip ends.
Angle adjustment wheel
Length adjustment wheel
Length adjustment wheel Width adjustment wheel
Height adjustment wheel
Step 1 Length
Adjustment range: 0 to 1.5 mm
Length adjustment wheel
+−
−
−
+
+
Step 2 Height and the tip end rotation angle * J type in the illustration.
Adjust the height and tip end rotation angle alternately.
- Height
Adjustment range: The tip end moves up and down repeatedly within a
certain range when the wheel is turned.
Height adjustment wheel
- Rotation angle of the tip end
Adjustment range: approximately 200°
Angle adjustment wheel
Step 3 Width between the tips
Adjustment range: 0 to 10 mm
Width adjustment wheel
Open
Close
Open Close
NOTE
5-2 Removing the tip
CAUTION
Perform procedures after the tip cools down.
Remove the tip using the iron cover on the iron holder after turning
the power source OFF.
(1) Slide the handpiece towards
the groove.
(2) Press the button with your
nger and x the tip in place.
(3) If the handpiece is pulled
backwards, the tip will remain
in the groove.
(4) Place the tips in the tip storing
pocket.
There are grooves on both sides.
Button
Tip
Button
Tip storing
pocket
(1)
(2)
(3)
6. Maintenance
CAUTION
Do not le oxide attached on the tip.
This will shorten the tip lifespan.
The product can be used for a longer period of time in a higher quality by
periodically implementing maintenance. The rate of consumption varies
depending on the use temperature as well as the quality and quantity of
the solder and ux. Perform maintenance depending on your state of use.
(1) Turn the power source ON.
(2) Wipe the tip with a cleaning sponge after the temperature stabilizes.
(3) If there is black oxide on the solder plating, feed new solder containing
ux, and clean it off using a cleaning sponge. Repeat this until the
oxide is removed.
Then, cover it with new solder.
(4) Turn off the power source and remove the tip after it has cooled.
If there is oxide attached to parts other than the tip end, remove it
using alcohol, etc.
(5) Replace the tip if it is deformed or has worn.
Daily Maintenance
Before work
Wipe the oxide on the tip and old solder with a cleaning
sponge.
Foreign matter entering the P.W.B. will cause poor solder
application.
When work
is suspended
Enable Sleep [ON] and place the handpiece on the iron
holder. This will reduce oxidation of the tip. Turn off the
power switch when not using the product for a long peri-
od of time.
After work is
nished
Wipe the tip with a cleaning sponge and cover the tip end
with new solder.
This will prevent oxidation of the tip.
2021.3
MA03217Jb210301
© 2021 HAKKO Corporation. All Rights Reserved.
Please access the web address below for other distributors.
https:// www.hakko.com
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL: [phone] FAX: [phone]
https://www.hakko.com E-mail: [email protected]
取説 FX-1003_EN_210301.indd 2取説 FX-1003_EN_210301.indd 2 2021/03/01 13:19:532021/03/01 13:19:53