Halo TGS3S401MSRB User manual

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerPr[email protected]
1
PACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
Instruction Manual / Manuel d’instructions/ Instrucciones
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or modica-
tions to this equipment not expressly approved by the manufacturer could void
the user’s authorization to operate this equipment. NOTE: This device complies
with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference including interference that may cause
undesired operation of the device.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install the motion sensor 8-12 feet above the
ground. (Motion sensor is less sensitive above
12 feet.)
• Locate motion sensor so motion moves across
detection zone (Fig. 1).
• Locate sensor away from heat producing sources
to prevent false triggering. Also be very careful
not to include objects such as windows, white walls and
water in the detection zone.
• Locate sensor away from moving objects such as trees, large shrubs and street
trac.
• Do not install more than one motion activated oodlight on one wall switch.
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your xture will void the warranty.
• Your xture is prewired and preassembled for easy installation.
• Read and follow these instructions.
• Risk of re/electric shock. If not qualied, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect xture to a 120 Volt, 60 Hz power source. Any other connection voids the
warranty.
• Fixture should be installed by persons with experience in household wiring or by
a qualied electrician. The electrical system, and the method of electrically con-
necting the xture to it, must be in accordance with the National Electrical Code
and local building codes.
• Mount xture to a grounded, recessed-mounted standard junction box marked for
use in wet locations.
• Suitable for wall mount or eave mount only. NOT suitable for ground mount
installation.
• For proper operation and protection against damage, the motion sensor head
adjustment knobs must be facing the ground.
• Do not mount below 5 feet.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following
2 conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
A. Light xture
ENGLISH
WARNING
TGS3S401MSRB
TGS3S401MSRW
TGS2S402MRRB
TGS2S402MRRW
TGS2S402MSRB
TGS2S402MSRW
TGS3S403MRRB
TGS3S403MRRW
TGS3S301MSRB
TGS3S301MSRW
TGS2S302MRRB
TGS2S302MRRW
TGS2S302MSRB
TGS2S302MSRW
TGS3S303MRRB
TGS3S303MRRW
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
1
FIG.1
MOTION SENSOR
A. Light xture
C. Gasket
E. Adapter Plate Kit
B. Mounting bracket
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in.
junction box screws
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
F. Decorative screw cover cap G. Wire connector
B. Mounting bracket
E. Adapter Plate Kit
F. Decorative screw cover caps
C. Gasket
A. Light fixture
PACKAGING CONTENTS
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)

2
ADJUSTING THE LUMEN OUTPUT
• This product features selectable lumen output. Choose between three preset
lumen outputs on the dial of the base housing before, during, or after installation
(Fig. 2):
• These settings are designated by the abbreviations located on the center dial on
the base housing (Fig. 2):
• High = 3000lm (Triple Head and Single Head), 2500lm (Twin Head Fixtures)
• Med = 2500lm (Triple Head), 2200lm (Single Head), 2000lm (Twin Head)
• Low = 2000lm (Triple Head), 1500lm (Single Head and Twin Head)
• Use a athead to rotate the dial so the arrow points toward the desired setting.
• DO NOT USE a power tool or over-rotate the dial
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Fixture can be wall or eave mounted (Fig. 3).
NOTE: Mounting bracket mounts to recessed mounted
standard junction boxes (Fig. 4). Junction box must be
at least 1-1/2 inch in depth for proper installation for
recessed mount application. For surface mount junction
box installation, refer to installation instructions included
with the adapter plate kit (E).
1. Line up the slots on the mounting bracket (B) with
the holes on your junction box. Using either (2)
#6 screws or (2) #8 screws (D) (depending on
size of the holes in your junction box), attach the
mounting bracket (B) to your junction box (Fig. 5).
Be sure the mounting bracket is installed with the
funnel for the central mounting screw going into
the junction box.
2. Make the electrical connection between the
ground wire on the mounting bracket and the
ground wire inside of the junction box.
3. Disconnect the male connector in the back of the
xture. Insert the junction box wires to the male
connector while ensuring the hot wire (black)
and neutral wire (white) are connected to the cor-
responding black and white connections on the
male connector. (Fig. 6)
Note: Be sure these are solid wires and stripped
3/8".
4. Plug the male connector into the female connec-
tor through the gasket (C). Rotate the connector
so it is recessed within the back surface of the
xture. (Figs. 7 & 8)
5. Attach xture (A) to the mounting bracket (B)
using the central mounting screw that is already
installed in the xture. Be sure no loose wires re-
main sticking out from underneath the coverplate.
Insert the decorative screw cover cap (F) into
the screw hole on the coverplate for a nished
appearance (Fig. 9).
6. Adjust light xture to desired position by loosen-
ing the thumbscrew on the upper arm. Move the
head to aim and retighten the thumbscrew.
7. Apply silicone caulk around the edges of the
canopy to provide a watertight seal from rain and
moisture.
8. Turn on power at main fuse/breaker box.
OPERATING YOUR FIXTURE
1. Rotate duration knob on bottom of the sensor to“TEST”.
2. Turn the arrow on the sensitivity knob to a middle point between “Max” and “Min.”
3. Turn on the power to xture. Allow xture to warm up approximately 40 seconds
before testing. (Lights may not come on during warm-up period.)
4. Aim sensor head toward desired detection area. The motion sensor should be aimed
down from the horizontal plane by a 5°–15° angle.
5. Walk across the detection zone at the farthest distance you wish your motion sensor
to detect motion.
6. Adjust sensor head angle until you get desired results. Lights will turn off 2-4 seconds
after all motion stops.
NOTE: For maximum range performance, allow xture to operate in any mode (with
power to the unit) for at least 48 hours.
7. To set the ON time, rotate duration knob arrow to point to the desired time setting
within the range (up to 12 minutes). This will be the duration the light stays on at full
output after motion is detected.
8. Select the Standby Dim Level of your xture by adjusting the Dim Knob on the bottom
of the motion sensor. If the knob is set to 0%, the xture will turn off when no motion
is detected, and the ON time selected in step 7 times out. If the knob is set to 100%
the xture will not dim when no motion is detected. If the knob is set to a point
between 0% and 100% the xture will dim to the set level when no motion is detected,
and the ON time selected in step 7 times out.
SELECTING YOUR DESIRED FEATURE
B
D
D
FIG.4
Junction box
5
B
A
FIG.6
6
3/8”
4
1-1/2 in.
Round
FIG.3
1-1/2 in.
Octagonal
7
FIG.7
FIG.7
8
C
A
B
FIG.8
9
Screw Cover Cap
F
Central Mounting
Screw
FIG.9
2
FIG.1
FLOOD
Mode of Operation Duration Adjustment Knob How to Set Power Switch
Auto Setting (motion
activated) Lights should
turn ON with motion only
at night and should turn
OFF according to the dial
setting.
Knob arrow points to
desired time setting
within the range.
Turn the power to the
xture ON.
Dusk to Dawn Setting
(activated only at night)
Lights should turn ON for
6 hours at dusk and then
reset to the Auto Setting.
Knob arrow points to
desired time setting
within the range.
Turn the power OFF
and ON twice within 3
seconds.
Test Setting
Lights should turn ON
with motion both day and
night. Lights should turn
OFF after 4 seconds.
TEST Turn the power to the
xture ON.
Return to Auto Setting
(motion activated)
From any of the above
settings.
Knob arrow points to
desired time setting
within the range.
Turn the power OFF for
at least 40 seconds and
then back ON.
3
Wall Mount Eave Mount
Eave mount
Wall mount
FIG.3
Eave mount
Wall mount
FIG.3